Advertisement
Available languages
Available languages
ENGLISH
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit from the
support that Philips offers, register your product at www.philips.com/welcome.
General description (Fig. 1)
A Cap of filling opening
B
Steam control
-
1 = minimum steam
-
2 = maximum steam
t= no steam
-
u= Calc-Clean function
-
C Temperature light
D Mains cord
E
Water tank
F
Soleplate
G Temperature dial
Important
Read this user manual carefully before you use the appliance and save it for future
reference.
Danger
-
Never immerse the iron in water.
Warning
-
Check if the voltage indicated on the type plate corresponds to the local mains
voltage before you connect the appliance.
-
Do not use the appliance if the plug, the mains cord or the appliance itself shows
visible damage, or if the appliance has been dropped or leaks.
-
If the mains cord is damaged, you must have it replaced by Philips, a service
centre authorised by Philips or similarly qualified persons in order to avoid a
hazard.
-
Never leave the appliance unattended when it is connected to the mains.
-
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
-
Children should be supervised to ensure that they do not play with the
appliance.
-
Do not let the mains cord come into contact with the hot soleplate of the iron.
Caution
-
If the appliance has an earthed plug, it must be plugged into an earthed wall
socket.
-
Check the mains cord regularly for possible damage.
-
The soleplate of the iron can become extremely hot and may cause burns if
touched.
-
When you have finished ironing, when you clean the appliance, when you fill or
empty the water tank and also when you leave the iron even for a short while:
set the steam control to the 'no steam' position, put the iron on its heel and
remove the mains plug from the wall socket.
-
Always place and use the iron on a stable, level and horizontal surface.
-
This appliance is intended for household use only.
Electromagnetic fields (EMF)
This Philips appliance complies with all standards regarding electromagnetic fields
(EMF). If handled properly and according to the instructions in this user manual, the
appliance is safe to use based on scientific evidence available today.
Before first use
1
Remove any sticker or protective foil from the soleplate.
2
Let the iron heat up to maximum temperature.
3
Pass the iron over a piece of damp cloth for several minutes to remove any
residues from the soleplate.
Note: The iron may give off some smoke when you use it for the first time. This ceases
after a short while.
Preparing for use
Filling the water tank
Never immerse the iron in water.
1
Make sure the appliance is unplugged.
2
Set the steam control to the 'no steam' position (Fig. 2).
3
Tilt the iron backwards.
4
Open the cap the of filling opening (Fig. 3).
2
5
Fill the water tank with tap water up to the maximum level. (Fig. 4)
Do not fill the water tank beyond the MAX indication.
Do not put perfume, vinegar, starch, descaling agents, ironing aids or other
chemicals in the water tank.
Note: If the tap water in your area is very hard, we advise you to mix it with an equal
amount of distilled water or to use distilled water only.
6
Close the cap of the filling opening.
Setting the temperature
1
Put the iron on its heel.
2
To set the required ironing temperature, turn the temperature dial to the
appropriate position (Fig. 5).
Check the laundry care label for the required ironing temperature:
Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester)
1
Silk
1
Wool
2
Cotton, linen
3
If you do not know what kind or kinds of fabric an article is made of, determine the
right ironing temperature by ironing a part that is not visible when you wear or use
the article.
Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent
shiny patches.
Start ironing the articles that require the lowest ironing temperature, such as those
made of synthetic fibres.
3
Put the mains plug in an earthed wall socket.
The temperature light goes on (Fig. 6).
,
4
When the temperature light has gone out, wait a while before you
start ironing.
The temperature light goes on from time to time during ironing.
Using the appliance
Steam ironing
1
Make sure that there is enough water in the water tank.
2
Select the recommended ironing temperature (see chapter 'Preparing for use',
section 'Setting the temperature').
3
After the temperature light has gone out, set the steam control to the
appropriate steam position. Make sure that the steam setting you select is
suitable for the ironing temperature selected: (Fig. 7)
Temperature settings
to
2
3
Temperature settings
to MAX for maximum steam 2.
3
The iron starts to produce steam as soon as it reaches the set temperature.
Ironing without steam
1
Set the steam control to the 'no steam' position (Fig. 2).
2
Select the recommended ironing temperature (see chapter 'Preparing for use',
section 'Setting the temperature').
Cleaning and maintenance
After ironing
1
Remove the mains plug from the wall socket and let the iron cool down.
2
Wipe scale and any other deposits off the soleplate with a damp cloth and a
non-abrasive (liquid) cleaner.
To keep the soleplate smooth, avoid hard contact with metal objects. Never use a
scouring pad, vinegar or other chemicals to clean the soleplate.
3
Clean the upper part of the appliance with a damp cloth.
4
Regularly rinse the water tank with water. Empty the water tank after cleaning.
Calc-Clean function
Use the Calc-Clean function once every two weeks. If the water in your area is very
hard (i.e. when flakes come out of the soleplate during ironing), use the Calc-Clean
function more frequently.
1
Set the steam control to the 'no steam' position (Fig. 2).
2
Set the temperature dial to MAX.
3
Fill the water tank to the maximum level.
Do not pour vinegar or other descaling agents into the water tank.
4
Put the mains plug in the wall socket.
for minimum steam 1.
4239.000.7060.4
Advertisement
