Related Manuals for Proline UPS T1000
Summary of Contents for Proline UPS T1000
- Page 1 USER MANUAL ON LINE UPS UPS T1000 / 2000 / 3000 Uninterruptible Power Supply www.pinnacle.co.za...
-
Page 2: Table Of Contents
CONTENT 1.SAFETY AND EMC INSTRUCTIONS................１ １ １ １ 1.1 I ......................１ NSTALLATION 1.2 O ......................１ PERATION 1.3 M ..............２ AINTENANCE SERVICING AND FAULTS 1.4 T ......................２ RANSPORT 1.5 S ....................... ２ TORAGE 1.6 S ......................３... - Page 3 13. SOFTWARE ......................２ １ ２ １ ２ １ ２ １ – W ..............２ １ OFTWARE OWNLOAD OWER APPENDIX 1 － － － － B ACK PANEL ................... ２ ２ ２ ２ ２ ２ ２ ２...
-
Page 4: Safety And Emc Instructions
Do not block ventilation openings in the UPS’s housing. Place cables in such a way that no one can step on or trip over them. ★ For UPS T1000/2000/3000 Socket-outlets and socket of batteries are earthed by the input power cord, please ★... -
Page 5: Maintenance Servicing And Faults
1.3 Maintenance, servicing and faults The UPS operates with hazardous voltages. Repairs may be carried out only by ★ qualified maintenance personnel. Caution - risk of electric shock. Even after the unit is disconnected from the mains ★ power supply (building wiring socket), components inside the UPS are still connected to the battery which are potentially dangerous. - Page 6 1.6 Standards * Safety IEC/EN 62040-1-1 * EMI Conducted Emission........:IEC/EN 62040-2 Category C1 Radiated Emission........:IEC/EN 62040-2 Category C1 Harmonic Current........:IEC/EN 61000-3-2 (Input Current≤16A) Voltage Fluctuation and Flicker....:IEC/EN 61000-3-3 (Input Current≤16A) *EMS ESD............:IEC/EN 61000-4-2 Level 4 RS............:IEC/EN 61000-4-3 Level 3 EFT............
-
Page 7: Description Of Commonly Used Notations
2. Description of commonly used notations Some or all of the following Notations may be used in this manual and may appear in your application process. Therefore, all users should be familiar with them and understand their explanations. ４... -
Page 8: Introduction
Model No. on the rear panel of the UPS. Model No. Type Model No. Type UPS T1000 UPS T1000S Standard Long backup time UPS T2000 UPS T2000S UPS T3000 UPS T3000S “S”... -
Page 9: System Description
4. System Description Figure 1: Display Panel Switch Function Turn on UPS system: By pressing the ON-Switch “I” the UPS system is turned on. ON - Switch Deactivate acoustic alarm: By pressing this switch an acoustic alarm can be deactivated. When mains power is normal, the UPS system switches to Standby mode by pressing OFF-Switch “... - Page 10 Display Function These LEDs show the load of the UPS system if the mains power is available (normal operation): 2nd LED 96%-105 % 3rd LED 76%-95 % LOAD and 4th LED 56%-75 % 5th LED 36%-55 % 6th LED. 0-35 % BATTERY CAPACITY In the battery operation, the LEDs indicate the capacity of the...
-
Page 11: Connection And Operation
If the UPS is connected via the power cord, please use a proper socket with protection against electric current, and pay attention to the capacity of the socket: over 10A for UPS T1000(S) & UPS T2000, over 16A for UPS T2000S& UPS T3000(S). - Page 12 c) Upon completion of the wiring configuration, please check whether the wires are securely affixed. d) Put the small cover back to the rear panel. Figure 2: Connection diagram of UPS T2000S(CE) and UPS T3000(S) 2.3) Computer Connection: Connect your computer to the outlet sockets of the UPS system following the above diagram.
- Page 13 5) Test Function: Test the function of the UPS system by either pressing the On-Switch “I” or disconnecting the input of the UPS system from the power supply. 6) Turn Off the UPS: 6.1) In Inverter Mode: Press “ “ button continuously for more than 1 second to turn off the UPS. Then the UPS will get into self-test status first.
- Page 14 (3) The battery connection procedure is very important. Any incompliance may result in the risk of electric shock. Therefore, the following steps must be strictly complied with. (4) First connect in series the batteries of the pack to ensure proper battery voltage.
-
Page 15: Trouble Shooting
6. Trouble Shooting If the UPS system does not operate correctly, please attempt to solve the problem using the table below. Problem Possible cause Remedy No indication, no warning tone even No input voltage Check building wiring socket outlet though system is connected to and input cable. -
Page 16: Maintenance
7. Maintenance 7.1 Operation The UPS system contains no user-serviceable parts. If the battery service life (3 - 5 years at 25°C ambient temperature) has been exceeded, the batteries must be replaced. In this case please contact your dealer. 7.2 Storage If the batteries are stored in temperate climatic zones, they should be charged every three months for 1-2 hours. -
Page 17: Technical Data
8. Technical Data 8.1 Electrical specifications INPUT Model No. UPS T1000(S) UPS T2000 UPS T2000S UPS T3000(S) Phase Single Frequency (46~54)Hz Current(A) OUTPUT Model No. UPS T1000(S) UPS T2000(S) UPS T3000(S) Power rating 1kVA/0.7kW 2kVA/1.4kW 3kVA/2.1kW Voltage 220/230/240 V AC ×... -
Page 18: Dimensions And Weights
8.4 Dimensions and weights Model No. Dimensions W x D x H (mm) Net Weight kg UPS T1000 145X400X220 UPS T1000S 145X400X220 UPS T2000 192X460X340 34.5 UPS T2000S 192X460X340 UPS T3000 192X460X340 35.5 UPS T3000S 192X460X340 １ ５... -
Page 19: Battery Maintenance
9. Battery Maintenance This series UPS only requires minimal maintenance. The battery used for standard models are value regulated sealed lead-acid maintenance free battery. These models require minimal repairs. The only requirement is to charge the UPS regularly in order to maximize the expected life of the battery. When being connected to the utility power, whether the UPS is turned on or not, the UPS keeps charging the batteries and also offers the protective function of overcharging and over-discharging. -
Page 20: Notes For Battery Disposal And Battery Replacement
10. Notes for Battery Disposal and Battery Replacement 1) Before disposing of batteries, remove conductive jewelry such as necklace, wrist watches and rings. 2) If it is necessary to replace any connection cables, please purchase the original materials from the authorized distributors or service centers, so as to avoid overheat or spark resulting in fire due to insufficient capacity. -
Page 21: Operating Mode
11. Operating mode 11.1 Utility power mode The display panel in utility power mode is shown in the following diagram. The utility power LED and the INV LED are turned on. The load level LEDs will be turned on in accordance with the load capacity connected. -
Page 22: Bypass Mode
again, the buzzer will stop beeping (in silence mode). Press the “ON” button once again for more than 1 second to resume the alarm function. Fig 15.2 Battery mode diagram 2) When the battery capacity decreases, the number of the battery capacity LEDs turned on will be reduced. -
Page 23: Communication Port
12. Communication Port 12.1 RS232 Interface The following is the pin assignment and description of DB-9 connector. Pin # Description Output Input Input 12.2 AS400 Interface(Option) Except for the communication protocol as mentioned above, this series UPS has AS400 card (an optional accessory) for AS400 communication protocol . Please contact your local distributor for details. - Page 24 13. Software Free Software Download – WinPower WinPower is a brand new UPS monitoring software, which provides user-friendly interface to monitor and control your UPS. This unique software provides safely auto shutdown for multi-computer systems while power failure. With this software, users can monitor and control any UPS on the same LAN no matter how far from the UPSs.
- Page 25 Appendix 1 B ack Panel － Back View of UPS T1000(S) Back View of UPS T2000(S) Non CE-certified Back View of UPS T2000S CE-certified & UPS T2000 CE-certified ２ ２...
- Page 26 Back View of UPS T3000(S) Non CE-certified Back View of UPS T3000(S) CE-certified ２ ３...
- Page 27 614-00279-01 ２ ４...
Need help?
Do you have a question about the UPS T1000 and is the answer not in the manual?
Questions and answers