Summary of Contents for Wallbed Gallery MURPHY BED A933
Page 1
A933 BOOKCASE MURPHY BED PACKING LIST BOX 1 A933F( )-H: HORIZ PANELS In Box 1 you will find 3 panel parts: The Crown top, the top back panel, and the center back panel You will have also found this set of instruction documents/ and the Bubble pack #1-which has all the hardware you'll need for step 1 of the instructions.
Page 2
A933 BOOKCASE BED HARDWARE LIST US PATENT PENDING PAGE 1 instruction step where bubble pack these parts POSITION ITEM PICTURE SIZE this item is first used are in box# ITEMS SHIPPED IN A933F()-H -- HORIZONTAL PANELS BOX ITEMS SHIPPED IN A903F()-H -- HORIZONTAL PANELS BOX instructions instructions ALLEN WRENCH...
Page 3
PAGE 2 ITEMS SHIPPED IN 103-B BOX -- SPRING BASE BOX ATTACHING BASE ARM WING BOLT M6x5/8" ATTACH THE SPRING BASE COARSE-THREAD SCREW #10 2.75" FLANGES TO THE FOOTER STUD bubble pack BRACKET 1.5x1.5" BOX #3 BOX #3 STABILIZE BED CASE TOP TO STABILIZE BED CASE TOP TO 3/4"...
Page 4
A933 Bookcase Murphy Bed Assembly Instructions Congratulations and a Big Thank You for your purchase of a Wallbed Gallery Murphy Bed! We sincerely appreciate your business! First – a few words of advice and caution: 1. Please do this job with two people. Attempting to do it alone, though heroic, could lead to product damage or injury because some things can be too heavy for just one person to safely handle.
PREPARATION FOR ASSEMBLY: 2 Please locate and confirm that you have the following 5 boxes. LIBRARY MURPHY BED – BOX LIST – Queen Size BOX # SKU# DESCRIPTION...
Page 6
3 STEP 0: INSTALL BOOK CASE 0A – Use screw connect side panel and bookcase IN BOX #2A and BOX#2B ,first Please find the pre-drilled hole on side panel, and use screw through the hinge on side panel. 0B – Install wheel under the bottom panel HOW TO CHOOSE THE WHEEL POSITION There are 2 blocks at the bottom of the ...
4 STEP 1: SETTING UP THE BED CASE FROM BUBBLE PACK #1, FOUND IN BOX #1, Please use the 11 bolts and barrel nuts, along with the #5 Allen Wrench and/or #5 Allen Head for Power Drill (the larger ones) to assemble the Bed Case as shown below. –...
Stand the assembled Bed Case up and move to the desired position against the wall. – 5 OPERATION SEQUENCE (Before you do this – check AGAIN that there is at least 20 inches from the wall to Top crown the side panels.) molding Beginwith TWO PEOPLE standing at the top center of the bookcases.
Page 9
STEP 2 : SETTING UP AND INSTALLING THE SPRING BASE MEASURE THICKNESS 6 OF BASE MOLDING The best results will be achieved by following these instructions carefully. TOOLS YOU WILL NEED TO SUPPLY: 1. A power drill gun with a #2 Phillips head, base molding 2.
Page 10
STEP 2C – You will notice that the left and right flange arms can be attached to the spring carriage in two positions 7 – and this is where the base-board thickness measurement comes in: OPTIONS: 1. If you have no base board or ¼” baseboard – you will use the pre-drilled wood Flange Spacer Blocks – and you will use the “extended” position.
Page 11
STEP 2D – Connect Flange arms and Spacer Brackets to the Spring Carriage Frame using the four Wing Bolts, and 8 Carefully place the Spring Carriage Frame into the bed case (don’t scratch the wood), then use Wing Bolts to attach the spacer brackets on each side.
Page 12
STEP 2F – Use the Anchor Screws in bubble pack #2 to connect Flange Arms to the Base Plate. 9 Stick your foot in here and press down while driving screws base molding FOOTER STUD Base Plate INSIDE THE inside the wall DRIVE SCREWS WALL A 10 DEGREE...
Page 13
STEP 3 – 10 Building the Bed Frame STEP 3A – Attach the mattress hoopand flip-over feet from box 3 to the bed tray from box 4 as shown here, and connect them with the connection hardware in bubble pack #3, and using the wrench and #4 Allen tools from bubble pack #1. Wing bolt ...
Page 14
STEP 3B – Install the assembled bed frame onto the spring carriage frame, By dropping the pivot bolt into pivot post. 11 Pivot Bolt Pivot Post Set the Assembled Bed Tray onto the spring base by dropping the Pivot Bolt into the slot at the top of the Pivot Post STEP 3C –...
Page 15
STEP 3D – With the doors still open, center the bed case at the top by inserting some folded pieces of cardboard in equal thickness 12 on either side. Put equally folded pieces of cardboard in each of the gaps between the flip‐over‐foot leg and the side panel . This assures the top of the bed case is “squared” with the bed frame. While the pieces of cardboard hold the bed case “square” to the metal tray, find two vertical studs in the wall and use the small bracket and screws in bubble pack #2 to affix the bed case in ...
Page 16
STEP 3E – Remove the two pieces of cardboard, install the door latch from box 1, and then close and latch the bookcase. 13 Install wood plug if side is exposed ...
14 APPENDIX 1 – Mounting your Murphy Bed to a concrete wall (such as is often found in a basement). If you have either brick or masonry WITHOUT DRYWALL - We recommend the TAPCON Concrete Screw System, model 3/16” x 2.1/4” flat-head screw.