Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Takachiho Sangyo TR-1
Summary of Contents for Takachiho Sangyo TR-1
- Page 1 Ground Penetrating Radar System Operator Manual TAKACHIHO SANGYO CO., LTD.
- Page 2 TR-1 Operator manual 861-081 Safety ■ Before use, please read well in this instruction manual, use the product definitely and safely. ■ Here listing instructions in the security by the indication such as follows. Please read the text after understanding contents of the indication well.
-
Page 3: Table Of Contents
TR-1 Operator manual 861-081 Table of Contents 1. Preparing for use ・・・・・ 1 2. Battery & Charging ・・・・・ 2 3. Raising the handle to its working position ・・・・・ 3 4. Adjusting the Display angle ・・・・・ 3 5. Method of starting ・・・・・... -
Page 4: Preparing For Use
TR-1 Operator manual 861-081 1. Preparing for use 1) Inspection method Please follow the guidelines to keep the unit a normal state. 1. Confirm that an antenna cover is attached to an antenna exactly. 2. Confirm that battery is completely charged and it is locked well. -
Page 5: Battery & Charging
TR-1 Operator manual 861-081 2. Battery & charging Battery pack is supplied. Please make sure it is charged fully before first use. Failure to do so may considerably shorten the life of the battery pack supplied. Battery is contained in the battery compartment by pushing the locking pin down. To release the lock, push the locking pin again, then, withdraw the battery pack. -
Page 6: Raising The Handle To Its Working Position
TR-1 Operator manual 861-081 3. Raising the handle to its working position Operation is on level ground and in safe location. Take off the safety fitting of the unit and open the handle stopper. Lift up the handle bar. Taking care not to let go until they are all the way back. -
Page 7: Method Of Starting
TR-1 Operator manual 861-081 5. Method of starting Move the power switch ON. Remove the battery when stored or no use for ！ CAUTION any length of time. Note. To prevent unintentional discharging of the battery, please remove the battery in case of transportation and temporary storage... -
Page 8: Choice Of Color Combination
TR-1 Operator manual 861-081 6. Choice of color combination When power on, a choice between two color combination is displayed. （Red / Yellow / Green） or（Yellow / Grey / Blue） Tap this area of the Tap this area of the... -
Page 9: Icons' Color Combination
TR-1 Operator manual 861-081 7. Icons’ color combination Depending on the color combination, the icon color to use for operation is as follows. Red/Yellow/Green Yellow/Grey/Blue Action color combination color combination icons icons Sensitivity up Sensitivity down Start forwards Start backwards... -
Page 10: Common Icons
TR-1 Operator manual 861-081 8. Common icons The following icons are commonly used no matter what color combination chosen. Icon Action Stop Stop collection of new data. Reset Reset measurement data. The next measurement is enabled. Overspeed（Warning） Appears if the data collection speed (walking pace) Becomes too fast for the system to deal with. -
Page 11: Chronos Masking Icons
TR-1 Operator manual 861-081 9. Chronos masking icons Action Icon Masking of data can be applied. Details see P13 to P15. 10. Battery status icons The following icons are used to represent the approximate value of current battery status. BATTERY <99% BATTERY <80%... -
Page 12: Start-Up Screen
TR-1 Operator manual 861-081 11. Start-up Screen Pushing the reset button will enter the “start scan” screen... -
Page 13: Start Scan
TR-1 Operator manual 861-081 12. Start scan Distance scale Indicates, in meter, rough distance from start of scan. Log collection up to 16 m is possible. Battery status Indicates battery status. (See P8) Data panel Displays progress and results here. -
Page 14: Scan In Progress
TR-1 Operator manual 861-081 13. Scan in progress Cursor Current position is marked by the Black cursor. Use central ►◄ for accurate positioning. Unprocessed data Not yet processed data is shown in Purple. Operator feet Allows approximate positioning relative to the operator. -
Page 15: Data Adjusting
TR-1 Operator manual 861-081 14. Data adjusting Increase sensitivity Press to increase the sensitivity. Sensitivity scale Center = Default Left = Low Right = High Reduce sensitivity Press to reduce the sensitivity. Cursor Place the antenna position in highly possible point of service in the screen. -
Page 16: Continuing Scan
TR-1 Operator manual 861-081 15. Continuing scan Stop a scan Press stop if you wish to finish your Scan After having moved the unit to reverse for data adjustment, able to continue the scan by moving the unit to the search direction again. Restart the scan automatically when it reaches at not-yet- processed data spot and new data is collected and the data panel begins scroll below. -
Page 17: Chronos Masking
TR-1 Operator manual 861-081 16. Chronos masking Provides masking of the measurement data. Masking setting is replaced whenever tapping Chronos masking. It is used when need to cutoff data depending on estimated depth or cutoff neighboring service to the vertical direction. -
Page 18: Chronos Masking Levels
TR-1 Operator manual 861-081 17. Chronos masking levels Masking level Icon Level 0 No masking. All data is displayed. Level 1 Top 16％ data is masked. Only Shallow & deepest data displayed. Level 2 Top 32％ data is masked. Only deepest data displayed. -
Page 19: Chronos Masking Examples
TR-1 Operator manual 861-081 18. Chronos masking examples Level 0 Level 1 Level 2 Level 3 Level 4 Comment Near surface Shallow Deeper Note the Capability to separate vertically adjacent services. Disappears Level 2 & 4 therefore Shallow Disappears Level 3 & 4... -
Page 20: Depth Estimation
TR-1 Operator manual 861-081 19. Depth estimation 1) Basic The estimated depth function is the function that the depth of the indicator value is displayed just to choose the data of the specific place with the cursor. To start a depth estimated function, while choosing data with the cursor, please tap the data Panel. -
Page 21: Measurement Example
TR-1 Operator manual 861-081 20. Measurement example 1 Put the cursor on the center of data which depth estimation is expected. Tap the screen anywhere within the data panel to show depth estimation. Estimated depth. （in meter） comes out. All data comes out. - Page 22 TR-1 Operator manual 861-081 21. Measurement example 2 Adjust sensitivity rather high and allow to analyze estimated depth even from weak signal. Near surface & shallow data are masked and the cursor is put on data of the remaining high depth.
-
Page 23: Measurement Example
TR-1 Operator manual 861-081 22. Measurement example 3 Set sensitivity to initial value. Deep depth data is masked. The cursor is on the center of near surface or shallow data. The estimated depth shows the existence of the different buried... -
Page 24: Finishing A Scan
TR-1 Operator manual 861-081 23. Finishing a scan Data is displayed right up to the cursor. Stop icon is replaced by the Reset icon. When push the stop, the collection of data is stopped at a position of cursor. But processing is continued and the collected data are displayed to the cursor position. -
Page 25: Replacing The Antenna Cover
TR-1 Operator manual 861-081 24. Replacing the Antenna Cover １）Place the TR-1 body on a workbench upside down so that the antenna is facing up。 ※ Take care to avoid putting undue weight on the monitor. ２）Using a Philips head... - Page 26 TR-1 Operator manual 861-081 ４）Place a new cover on the antenna. ５）Return the 6 screws that were removed in step one and fasten the cover to the antenna When replacing the cover, tighten the bolts by hand, taking care ！ Caution...
-
Page 27: Product Specification
TR-1 Operator manual 861-081 25. Product specification Working temperature range : -10 C ~ +50 C Material : Shock resistant plastic Size, Weight Antenna retracted : 340 mm (H) x 860 mm (L) x 510 mm (W) Antenna extended : 820 mm ~ 1185 mm (H ) x 1085 mm ~ 1290 mm (L) Weight : 16.8kg... - Page 28 TR-1 Operator manual 861-081 Call & Contact TAKACHIHO SANGYO CO., LTD Tokyo office 32-8, 5-Chome, Shiba, Minato-Ku, Tokyo 108-0014 TEL 81-3-3453-4778 Head office & Factory in Nagoya, Japan 2018.6...
Need help?
Do you have a question about the TR-1 and is the answer not in the manual?
Questions and answers