Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for X-Tronic 4040-XTS
Summary of Contents for X-Tronic 4040-XTS
- Page 1 X-TRONIC USA X-Tronic Model #4040-XTS Instructions...
-
Page 3: Table Of Contents
Replacing Heating Elements ..........13 Warranty and Contact Info ..........14-15 Thank you for purchasing the X-Tronic #4040-XTS SMT/SMD Rework/ Soldering station. This 2-in-1 station is designed to meet all of your soldering and reworking needs including BGA re-balling and reflow. -
Page 5: Package Contents
INTRODUCTION Package Contents • 1 – X-Tronic #4040-XTS Hot Air Rework Station • 1 – X-Tronic Soldering Iron • 1 – Soldering Iron Stand (w/Sponge) • 1 – Hot Air Gun • 1 – IC Popper • 1 – Stainless Steel Tweezers • 1 –... -
Page 6: Product Specifications
Soldering Iron Product Specifications MODEL 4040 Power Consumption 700 Watts Dimensions 4.9 x 7.4 x 9.8 in / 12.4 x 17.4 x 24.9 cm Weight 9.9 lbs. / 4.5 Kg Working Environment 0°F - 122°F / 0°C - 50°C Storing Environment -68°F - 176°F / -20°C - 80°C Input Voltage AC 110/120V - 60Hz... -
Page 7: Product Set Up
PRODUCT SET UP 1. Unpack all of the contents of the X-TRONIC # 4040-XTS Kit. 2. Remove the 2 Red screws from the bottom of the main unit. NOTE: Failure to complete this step could result in permanent damage to the unit! 3. -
Page 8: User Interface
iii. Adjust the temperature to the desired value using the Air Temp Control knob located in the upper right hand corner of the front panel. iv. Adjust the air flow to the desired amount using the Air Set knob located in the center right of the front panel, directly beneath the Air Temp set knob. -
Page 9: Safety Precautions
element from overheating and breaking down. 5. When using the soldering iron for the first time, be sure to allow the iron to come to proper temp and then clean and tin the tip to provide longer life expectancy. 6. When “---“ is displayed on the LED display, this means that the outlet temperature of the hot air gun is below 100°C, the handle has been properly replaced into the holster, and that the unit is in standby mode. -
Page 10: Maintenance
MAINTENANCE Unit 1. Keep the unit plugged into a GROUNDED outlet at all times during operation. 2. Keep the unit and all components free from dirt, debris, and liquid at all times. 3. Make sure the power cord is plugged in correctly and is kept safely off the floor to prevent accidents. -
Page 11: Install/Remove Hot Air Attachment
2. Allow the soldering iron and tip to reach room temperature. 3. Loosen the nut at the base of the metallic shaft of the soldering iron. 4. Slide the metallic tube off of the soldering iron and tip. 5. Slide the tip off of the heating element. 6. -
Page 12: Troubleshooting Guide
Troubleshooting Guide Problem Solutions Nothing appears • Check to ensure that the unit is plugged in to happen when • Make sure that the plug used is grounded turning the unit • Check for a blown fuse on the main power input, replace it if needed • Make sure the breaker is not tripped • Contact the manufacturer... - Page 13 11. Replace the heating element. 12. Solder the new element leads in the correct location. 13. Pull the cord out of the bottom of the soldering iron while pushing the new element into the top, aligned with the notches. 14. Replace the plastic nut on the top of the iron and tighten. 15.
- Page 14 All X-Tronic Products come with 3-Year Guarantee, valid only in the 48 Contiguous United States. If you purchase this product and ship it to a destination outside of the 48 Contiguous United States this warranty ...
- Page 16 Compliments please call or email us. Toll Free: 844-861-4762 Info@XTronicUSA.com Our Business Hours are: Monday - Thursday: 8am - 4pm CST Friday: 8am - Noon CST If you would like to shop for other X-Tronic International Products Please visit our website www.XTronicUSA.com...