Summary of Contents for Flight Display Systems FD104SMT
Page 1
Page 1 of 16 FD104SMT Installation and Operation Manual 10.4” LCD and Slide Mount Manufactured by MILIC, LLC with marketing support from Flight Display Systems. This product does not have FAA PMA approval. TECHNICAL SUPPORT +1 (678) 867-6717, or www.FlightDisplay.com...
All manuals and user guides at all-guides.com Rev: Revision Date: 09/04/2012 MAN – FD104SMT Page 3 of 16 Table of Contents General Information ........................4 1. Front View ..........................4 2. Additional information ....................4 Specifications ..........................5 Installation Instructions ......................5 1. Power ..........................5 Wiring Suggestions ........................6...
Right configuration. The FD104SMT-L is mounted on the Left side of the bulkhead, to extend to the right into the aisle, while the FD104SMT-R is installed on the Right side of the bulkhead, extending to the left into the aisle.
FD104SMT is secured by four #10 machine screws. The monitor locks into place when stowed and held in place by a gas spring when deployed. There is one DB-15 male connector on the back of the unit. The FD104SMT comes with a female DB-15 connector and crimp pins. The FD104SMT has already been connected to the slide mount and tested prior to shipping.
All manuals and user guides at all-guides.com Rev: Revision Date: 09/04/2012 MAN – FD104SMT Page 6 of 16 Wiring Suggestions All shields should be grounded to the connector at the source, and floating at the display. Avoid routing video wiring parallel to: ...
All manuals and user guides at all-guides.com Rev: Revision Date: 09/04/2012 MAN – FD104SMT Page 7 of 16 VGA Wiring Recommended cable for VGA purpose is ECS P/N 453005. This is a single shielded cable containing 5 separate coaxial cables, color-coded to match the functions of the wires.
All manuals and user guides at all-guides.com Rev: Revision Date: 09/04/2012 MAN – FD104SMT Page 8 of 16 Power and Ground Wiring This is a 28VDC monitor that requires 1 amp of power to operate. To operate properly this monitor requires an input voltage of 18-29VDC.
All manuals and user guides at all-guides.com Rev: Revision Date: 09/04/2012 MAN – FD104SMT Page 9 of 16 Power/Video Pin out for High Density DB-15 Receptacle Part Numbers for DB-15 connectors, manufactured by Tyco or Amp. High density, D-sub, 15 contact receptacle (female)
It is necessary to stow the display during take-off and landing. The passengers will be able to change the video output on the FD104SMT using the video source select button on the display, or remotely throughout the cabin with the included IR remote.
All manuals and user guides at all-guides.com Rev: Revision Date: 09/04/2012 MAN – FD104SMT Page 13 of 16 Troubleshooting Video Noise Check for an incorrect ground in the installation wiring. See specific examples of video noise below, or visit http://flightdisplay.com/Grounding.pdf VGA Shadowing Most of shadowing problems are due to shielding on the wire.
Fax: +1 (678) 867-6742 Email: sales@flightdisplay.com For further product information, technical data and sample wiring diagrams, please click on the Dealers section of our web site at www.flightdisplay.com Instructions for Continued Airworthiness The FD104SMT is designed not to require regular general maintenance.
6717 to obtain assistance. If the return of the unit to the factory is required, an RMA number will be issued at that time. Flight Display Systems will, upon receipt of the failed hardware, remanufacture or replace the unit at our discretion.
All manuals and user guides at all-guides.com Rev: Revision Date: 09/04/2012 MAN – FD104SMT Page 16 of 16 Log of Revisions Date Page Description 11/3/2008 Initial Release 04/10/2009 2,11 Updated specifications, warranty info 09/04/2012 Updated format, warranty and non-PMA info...