Related Manuals for Teamson Home PT-WF0004
Summary of Contents for Teamson Home PT-WF0004
- Page 1 Peaktop TIME SAVER! 21.26 Inch Freestanding Water 3D Interactive Instruction Decor with Fire Pit PT-WF0004 www.teamson.com...
- Page 2 ** Got questions? Please have your product code (on the first page of this instruction, e.g. PT-WF0004) and the order number ready, give us a call or email us through our customer care support! We are always ready to assist you!
- Page 3 Serving you well gives us great joy! +1(800)935-3959 Mon - Fri 10:00am ~ 2:00pm EST support@teamson.com +44(0)1952-916-050 Mon - Thu 9:00am ~ 5:00pm GMT Friday 9:00am ~ 4:00pm GMT support@teamson.co.uk 深圳办公室: +86(0755)8885-3558.分机号108 Mon - Sat 9:00am ~ 5:00pm GMT+8 sales_ec@teamson.com 台北辦公室: +886(2)2556-6268 Mon - Fri 9:00am ~ 5:00pm GMT+8...
-
Page 4: Safety Information
SAFETY INFORMATION WARNING DANGER Do not store or use gasoline or other FIRE OR EXPLOSION HAZARD flammable vapors and liquids in the If you smell gas: vicinity of this or any other appliance. Shut off gas to the appliance. • Extinguish any open flame. - Page 5 Product Parts Burner connection Burner Screw Body 2PCS 2PCS Thermocouple !Regulator assembly fire glass Control Knob 1Box WARNING: 1. Do not let any sharp objects touch or rub the surface of the product. 2. When assemblying, do not let children play around the working area. Questions? 3.
-
Page 6: Installation Instructions
INSTALLATION INSTRUCTIONS WARNING: This item heavy. necessary precautions should be taken when lifting and assembling this fireplace. Make certain the fireplace body always remains upright. Do not lie on its side or you could cause damage to the body. Most parts of this fireplace are pre-assembled (Figure 1) before shipment. - Page 7 INSTALLATION INSTRUCTIONS OF THE FOUNTAIN Put the basin stand on a clean level surface that cannot be damaged by water. Put the pump in the fountain basin, Thread the electrical cord through the pipe that is not in the center down into the center of the stand.
-
Page 8: Maintenance Information
OPERATION INSTRUCTIONS Lighting and Setting Control for Gas Before lighting, make sure the valve knob is in the “OFF” position. 1. From the OFF position, push in and turn control knob anti-clockwise to the LOW position. 2. Always perform a leak test before lighting the burner. See page 4 3. - Page 9 SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so may result in a fire explosion, injury, or death. WARNING • The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI Z223. 1/ NFPA54, OR CAN/CGA-B149.1, National gas and Propane Installation Code.
- Page 10 SAFETY INFORMATION • Combustible material should not be within 72 inches of the top of the unit, or within 48 inches around the entire unit. • If the flame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial lighting procedure.
- Page 11 SAFETY INFORMATION NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned "OFF" before assembling. Do NOT attempt to assemble without proper tools. IF APPLICABLE: • Allow unit to cool completely before placing on the protective cover •...
- Page 12 TROUBLESHOOTING Igniter pin and burner are wet Dry off with a soft cloth Check which direction the battery Igniter battery is incorrectly inserted is inserted Contact Teamson design corp. for Igniter pin is broken Heating unit won’t light a replacement part Reconnect wire to the igniter box located Electrode wire is loose or inside the table behind the igniter box...
- Page 13 SAFETY INFORMATION IF APPLICABLE: • Allow heating item to cool completely before placing on lid. • DO NOT use heating item while lid is installed. Always remove the lid while heating item is in use. Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied directly by Teamson design corp.