Related Manuals for Teamson Home Peaktop
Summary of Contents for Teamson Home Peaktop
- Page 1 Peaktop TIME SAVER! 30" Rattan Base Tempered 3D Interactive Instruction Glass Top Propane Firepit HF30200AA www.teamson.com...
- Page 2 √ ** Got questions? Please have your product code (on the first page of this instruction, e.g. HF30200AA) and the order number ready, give us a call or email us through our customer care support! We are always ready to assist you!
- Page 3 Serving you well gives us great joy! +1(800)935-3959 Mon - Fri 10:00am ~ 2:00pm EST support@teamson.com +44(0)1952-916-050 Mon - Thu 9:00am ~ 5:00pm GMT Friday 9:00am ~ 4:00pm GMT support@teamson.co.uk 深圳办公室: +86(0755)8885-3558.分机号108 Mon - Sat 9:00am ~ 5:00pm GMT+8 sales_ec@teamson.com 台北辦公室: +886(2)2556-6268 Mon - Fri 9:00am ~ 5:00pm GMT+8...
-
Page 4: Safety Information
SAFETY INFORMATION WARNING DANGER Do not store or use gasoline or other FIRE OR EXPLOSION HAZARD flammable vapors and liquids in the If you smell gas: vicinity of this or any other appliance. Shut off gas to the appliance. • Extinguish any open flame. - Page 5 SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so may result in a fire, explosion, injury or death. WARNING • The installation of this unit must adhere to local codes or Propane Storage and Handling Code,CSA B149.2.
- Page 6 SAFETY INFORMATION • if the flame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial lighting procedure. Once you have a flame started, hold down the control knob for 1 minute. • Do not add water into the unit. •...
- Page 7 SAFETY INFORMATION IF APPLICABLE: • Allow heating item to cool completely before placing on lid. • DO NOT use heating item while lid is installed. Always remove the lid while heating item is in use. Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied directly by Teamson design corp.
- Page 8 Product Parts Door Back Panel Front Panel Fire Table with Burner Lava Rocks Metal Stand PVC Cover Right Panel Contorl Knob 1BOX(3KGS) Washer Screw(M6*30MM) Screw(M6*16MM) 12PCS 8PCS 4PCS WARNING: 1. Do not let any sharp objects touch or rub the surface of the product. Questions? 2.
-
Page 9: Assembly Instruction
ASSEMBLY INSTRUCTION Do not lock the screws until the assembly is complete. Step1.Check that the control knob (J) for the gas supply system is turned to the 'OFF' position before starting any assembly. Step2. Attach back panel (E), right panel (F) and front panel (D) together using 4 pcs M6 x 30 screws (L) and 4 pcs washers (M) . - Page 10 ASSEMBLY INSTRUCTION Step3.Attach the metal stand (G) to the woven base using 4 pcs M6 x 30 screws (L) and 4 pcs washers (M) . Step4.Attach woven base to the bottom part of the table top (B) using 4 pcs M6 x 16 screws (K) and 4 pcs washers (M). Questions? Scan Here...
- Page 11 ASSEMBLY INSTRUCTION 5.Put the table lid. Questions? Scan Here...
- Page 12 ASSEMBLY INSTRUCTION Step6. Insert the bottom of the door (C) to the hole on the metal stand (G) and rotate the top to the unit, this will attach the door (C) to the body. Questions? Scan Here...
- Page 13 ASSEMBLY INSTRUCTION Place propane gas tank (not included) into the metal stand (G). Make sure the gas tank sits on the metal stand completely. Turn the cylinder valve on the tank clockwise to close the propane tank. Attach the preassembled regulator from the table top (B) PRESSURE RELIEF VALVE to the cylinder valve by turning the regulator...
-
Page 14: Operation
OPERATION 1.Make sure the control knob is in the "OFF" position. 2.Open the door and slowly open the valve on the propane gas tank by turning the knob counterclockwise. 3.Close the door on the body. 4.Push the ignition control knob in fully and rotate about 1/4 turn counterclockwise until a click is heard, it may take several attemps to light the burner. - Page 15 TROUBLESHOOTING Igniter pin and burner are wet Dry off with a soft cloth Check which direction the battery Igniter battery is incorrectly inserted is inserted Contact Teamson design corp. for Igniter pin is broken Heating unit won’t light a replacement part Electrode wire is loose or Reconnect wire to the igniter box located disconnected...
- Page 16 SAFETY INFORMATION In the event of gas leakage, the appliance shall not be used or if alight, the gas supply shall be shut-off and the appliance shall be investigated and rectified before it is used again. Tighten any leaking fittings, then turn on gas supply and recheck.If necessary, substitute gasket (according to EN 549 Class B2) Maintenance and Cleaning To enjoy years of outstanding performance from your appliance, regular services of the...