1. Manuals
  2. Brands
  3. Nordic Manuals
  4. Sander
  5. BS-L0218
  6. Operating manual

Nordic BS-L0218 Operating Manual

18v cordless belt sander
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
18V CORDLESS
BELT SANDER
OPERATING MANUAL
BS-L0218

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BS-L0218 and is the answer not in the manual?

Questions and answers

Related Manuals for Nordic BS-L0218

Summary of Contents for Nordic BS-L0218

  • Page 1 18V CORDLESS BELT SANDER OPERATING MANUAL BS-L0218...

  • Page 2: Product Specification

    NORDIC PRODUCT SPECIFICATION Voltage: No Load Speed: 120-320M/min Belt Size: 457x76mm  This tool requires a 4.0AH or 5.0AH battery. (2.0AH not recommended) GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and instructions. Failure to heed warnings and follow instructions may result in electric shock, fire and/or serious injury.

  • Page 3: Personal Safety

    NORDIC • Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and refrigerators. There is an increased risk of an electric shock if your body is earthed. • Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will increase the risk of an electric shock.

  • Page 4: Cutting Procedures

    NORDIC the power tool or these instructions to operate it. Power tools are potentially dangerous in the hands of untrained users. • Maintain power tools. Check for misalignment or jammed moving parts, breakages or any other feature that might affect the operation of the power tool. If it is damaged, the power tool must be repaired. Many accidents are caused by using poorly maintained power tools.

  • Page 5: Additional Safety Warnings

    NORDIC • Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. ADDITIONAL SAFETY WARNINGS 1. Do not allow foreign matter to enter the hole for connecting the rechargeable battery.
  • Page 6 NORDIC • Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators and other polymer components may be damaged resulting in electrolyte leakage and/or internal short circuiting leading to heat generation causing rupture or file. Moreover do not dispose of the batteries in fire, explosion and/or intense burning may result.

  • Page 7: Operation

    NORDIC Class II - The machine is double insulated; Earthing wire is therefore not necessary (only for charger) Ambient temperature 40°C max. (only for battery) Do not expose charger and battery pack to water Use battery and charger only in closed rooms Do not incinerate battery pack or charger Protect from the rain.
  • Page 8 NORDIC The red light will go off after charging is complete and a green light will appear. NOTE: Batteries may become warm while charging. This is normal. If the battery is hot after continuous  use in the tool, allow it to cool down to room temperature before charging. This will extend the life of your batteries.

  • Page 9: Turning The Sander On/Off

    Failure to do so movingbatterypackwillpreventaccidental could cause accidental starting, leading to serious ould cause serious personalinjury. personal injury. NORDIC TURNING THE SANDER ON/OFF NING: TURNING THE SANDER ON/OFF eye protection with side shields marked to ANSI Z87.1.
  • Page 10 USING SANDING BELTS Before connecting the sander to a power supply, always make sure it is not in the “locked-on” position. Failureto To install/change sanding belts: NORDIC do so could result in accidental starting of the sander Remove the battery pack. ...

  • Page 11: Dust Collection Bag

    Raise the tension release lever.  NORDIC  Depress the switch trigger and release immediately. NOTE: If you are changing sanding belts, remove  Choose one of these options: the old sanding belt at this time.

  • Page 12: Operating The Sander

    To empty the dust collection bag: Remove the battery pack.  NORDIC Remove the dust collection bag from the sa  Unzip the dust bag  To empty the dust collection bag: Shake out the dust.  •...

  • Page 13: Proper Hand Placement

     Possible motor burnout e the battery pack.  Irregular sanding belt tracking e the dust collection bag from the sander. NORDIC he dust bag PROPER HAND PLACEMENT out the dust. he dust bag. level with the workpiece, and keeping hands clear of e the dust collection bag.
  • Page 14 NORDIC NOTES:...
  • Page 15 NORDIC NOTES:...
  • Page 16 NORDIC...

Table of Contents