Hide thumbs Also See for AC62:

Advertisement

Quick Links

Install Guide
AC62 Door Controller
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
sales@verkada.com
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AC62 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Verkada AC62

  • Page 1 Install Guide AC62 Door Controller Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com Copyright © Verkada Inc. All rights reserved.
  • Page 2: Document Details

    (V1.0 first published 20220620) Firmware Firmware version can be verified on Verkada Command command.verkada.com. Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com Copyright © Verkada Inc. All rights reserved.
  • Page 3 Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com...
  • Page 4 After connecting the AC62 to network and power, visit: verkada.com/start For detailed installation instructions, visit: verkada.com/support Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com Copyright © Verkada Inc. All rights reserved.
  • Page 5 Flashing Blue - Controller is managing doors, but cannot reach the server Solid Blue - Controller is managing doors and connected to the server Flashing Pink - Identify Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com...
  • Page 6 2 Ports for: AUX, Fire Alarm Interface(FAI) 3 Ports for: AC, Ethernet, USB, UPS, Door Tamper Status LED Ethernet Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com Copyright © Verkada Inc. All rights reserved.
  • Page 7: Installation

    Lay AC62 on a flat surface, open the door and remove the cardboard. Keep cardboard intact for next step. Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com Copyright © Verkada Inc. All rights reserved.
  • Page 8 Installation Mounting 1/4 Use cardboard piece with the mounting template, kept from the previous step, to get a sense of the space AC62 will occupy on the wall. Use mounting template to drill pilot holes for the mount plate. Use the supplied screws to install the mount plate onto the wall.
  • Page 9 Unlock and open the enclosure door with the supplied key. Remove the door by sliding it upwards. Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com Copyright © Verkada Inc. All rights reserved.
  • Page 10 Use the supplied screws to secure the enclosure onto the wall according to thru holes. Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com Copyright © Verkada Inc. All rights reserved.
  • Page 11 Reattach the door to the enclosure. Connect the grounding cable from the enclosure to the door Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com Copyright © Verkada Inc. All rights reserved.
  • Page 12: Recommended Wiring

    • The other end of the drain wire shouldn’t be connected to anything. Required Network Settings An Ethernet connection with DHCP must be used to connect the AC62 to the Local Area Network (LAN). You also need to configure firewall settings to communicate with the AC62.
  • Page 13 Ensure power is disconnected from the AC62 and locking hardware before wiring, removing or inserting cassettes, readers, locks or any other peripherals. The AC62 comes equipped with a Form C relay that can be driven dry or wet. AC41 is rated to power 12V locks up to 1A and 24V locks up to 500mA.
  • Page 14 • Set it to “24VDC” for 24 Volt locking hardware configuration, ensure the negative of the lock goes into the COM port as shown in the The AC62 is rated to power 12V locks up to 1A and diagrams below. 24V locks up to 500mA.
  • Page 15: Connecting The Reader

    4. Connecting the Reader The AC62 is rated to power readers at 12V up to 250mA via the + (VIN) and – (GND) connection. Verkada readers use the top 4-port inputs while Standard Wiegand readers use the bottom 6-port inputs. The drain wire of the shielded cable should be secure to the nearest AC62 chassis ground.
  • Page 16: Connecting The Inputs

    NORMALLY CLOSED (NC). NORMALLY OPEN (NO). The REX can be configured to release the lock in Verkada command; most commonly seen in electromagnetic locks. The REX unlock time can also be configured. Verkada Inc. 405 E 4th Ave, San Mateo, CA, 94401 All specifications are subject to change without notice.
  • Page 17 For safety-related applications, wire the REX directly to the mag lock. You can wire additional REX switches and sensors to the door cassette if needed. Configuration Configuration Verkada Inc. 405 E 4th Ave, San Mateo, CA, 94401 All specifications are subject to change without notice. sales@verkada.com Copyright © Verkada Inc . All rights reserved.
  • Page 18: Aux Setup

    AUX inputs to be NORMALLY OPEN (NO). With the AC62’s AUX inputs you can hook up devices such as intercoms and buttons. All associated events will be logged in Command. The AUX Inputs can be programmed in Command to initiate a lockdown or unlock a door (or a set of doors).
  • Page 19 FAI- and FAI_P. A jumper wire must be connected across FAI+ and FAI_P. When the contact is open, this activates the FAI in the AC62 which disables 12V/24V power to all 16 relay outputs. Normally Open Input A normally open fire alarm input from an FACP should be wired across FAI+ and FAI-.
  • Page 20 Daisy Chaning Two AC62 FAI may be daisy chained. The FAI and latching states from the primary AC62 will be repeated in the secondary (daisy chained) unit. Verkada Inc. 405 E 4th Ave, San Mateo, CA, 94401 All specifications are subject to change without notice.
  • Page 21 Connect / Powering up device Connect Connect the AC62 to your network using either of the Ethernet ports located at the bottom of the controller. If you are installing multiple controllers, you can connect up to 4 additional controllers via the spare Ethernet port on each controller.
  • Page 22: Battery Backup(Optional)

    Lead Acid Rechargeable battery. Connect Connect the AC62 to your network using either of the Ethernet ports located at the bottom of the controller. If you are installing multiple controllers, you can connect up to 4 additional controllers via the spare Ethernet port on each controller.
  • Page 23 Appendix Support Thank you for purchasing this Verkada product. If for any reason things don’t work right, or you need assistance, please contact us immediately. verkada.com/support Sincerely, The Verkada Team Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 All specifications are subject to change without notice sales@verkada.com...

Table of Contents