Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NEO 15201
Summary of Contents for NEO 15201
- Page 1 15201 Betmakers Kiosk (TSST) USER SERVICE MANUAL 15201-ML002 REV05 ECN 5847...
- Page 2 5790 L.DICKSON FORMAT & CLARIFICATION OF STEPS 15-12-2021 5790 ADDITION OF FCC NOTATION L.DICKSON UPDATE CHAPTER 5.6 FROM: 4x SCREWS TO: 2x SCREWS. 21-03-2022 5847 L.DICKSON ADDITION OF 400W TO POWER SUPPLY (2.1.3 ELECTRICAL) 15201-ML002 REV05 ECN 5847 Page 2...
-
Page 3: Table Of Contents
6. Replacing the Bill Validation Module 7. Replacing the PC 8. Replacing the Teller LCD Screen 9. Adjusting the Customer LCD Screen 10. Replacing the NFC Reader 11. Replacing the Customer LCD Screen 12. Replacing the Proximity Sensor 15201-ML002 REV05 ECN 5847 Page 3... -
Page 4: Notices
Neo Products believes it is appropriate to do so. Changes will be incorporated in new editions of the publication and replaces all previous releases. -
Page 5: Safety Information
To avoid a shock hazard: • If Neo Products supplied a power cord, connect power to this unit only with the Neo Products provided power cord. Do not use the Neo Products provided power cord for any other product. •... -
Page 6: Caution Notices
Properly shielded and grounded cables and connectors must be used in order to meet emission limits. Neo Products is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. -
Page 7: Product Description
The Kiosk is connected to power using and earthed IEC cable this is to be provided by the installer. Power and Data connection can be accessed from under the unit Power on/off switch Ethernet connection 15201-ML002 REV05 ECN 5847 Page 7... -
Page 8: Replacing The Printer Module
STEP 3 Remove the paper roll spindle. Push the paper roll spindle inwards to allow it to slide upwards and out of the printer swing bracket. STEP 4 Undo the Latch Swell to disengage the green printer tray. Latch Swell 15201-ML002 REV05 ECN 5847 Page 8... - Page 9 Printer Module to the green tray. STEP 7 Remove 3x plugs from rear of the Printer Module. Printer Power Data Low paper sensor To re-install the replacement Printer Module, follow Steps 1 to 7 in reverse. 15201-ML002 REV05 ECN 5847 Page 9...
-
Page 10: Replacing The Msr Module
Top Lid to allow the Top Lid to lift open. STEP 2 Undo the Latch Swell to disengage the green tray. STEP 3 Remove the MSR Module from the peripheral tray. 15201-ML002 REV05 ECN 5847 Page 10... - Page 11 Unplug the power connector. STEP 5 Remove & retain 4x Pan Head Screws fastening the MSR Module to the green tray. To re-install the replacement MSR Module, follow Steps 1 to 5 in reverse. 15201-ML002 REV05 ECN 5847 Page 11...
-
Page 12: Replacing The Bna Module
STEP 2 Unlock the BNA Lock Bracket using the key provided. STEP 3 Swing open the BNA Lock Bracket. STEP 4 Pull the yellow handle of the BNA Cash Box from the BNA Bracket. 15201-ML002 REV05 ECN 5847 Page 12... - Page 13 STEP 6 Remove & retain 2x Pan Head Screws fastening the BNA Mount Bracket to the base. STEP 7 Re-close the BNA Lock Bracket and lock. STEP 8 Hold the BNA Lock Bracket as shown. 15201-ML002 REV05 ECN 5847 Page 13...
- Page 14 Place the BNA Mount Bracket on its side to access the 2x plugs connected to the USB Hub. STEP 11 Remove 2x plugs from the USB Hub. To re-install the replacement BNA Module, follow Steps 1 to 11 in reverse. 15201-ML002 REV05 ECN 5847 Page 14...
-
Page 15: Replacing The Bill Validation Module
Note: Remove the Bill Validation Module by guiding the small tabs on the Module past the slots on the BNA Bracket. To re-install the replacement Bill Validation Module, follow Steps 1 to 3 in reverse. 15201-ML002 REV05 ECN 5847 Page 15... -
Page 16: Replacing The Pc
PC Tray to the Main Frame. STEP 4 The PC Tray travel is limited by the Main Loom length. Partially pull out the PC Tray ensuring that there is suitable support under the Tray prior to full removal. 15201-ML002 REV05 ECN 5847 Page 16... - Page 17 PC Tray can be completely removed from the Kiosk. STEP 7 Remove & retain 4x Nuts fastening the PC to the base. To re-install the replacement PC, follow Steps 1 to 7 in reverse. 15201-ML002 REV05 ECN 5847 Page 17...
-
Page 18: Replacing The Teller Lcd Screen
STEP 2 Remove & retain 2x M8 Screws from the Cover Stay attached the Teller LCD Screen. STEP 3 Disconnect 3x LCD Screen Loom HDMI plugs into the USB Hub. Monitor Power STEP 4 Swing open the Bet Slip Reader Swing Mount. 15201-ML002 REV05 ECN 5847 Page 18... - Page 19 Teller side STEP 7 Support the Teller LCD Screen. Remove & retain 2x Bush Hinge & 2x M6 Pan Head Screws. To re-install the replacement Teller LCD Screen, follow Steps 1 to 7 in reverse. 15201-ML002 REV05 ECN 5847 Page 19...
-
Page 20: Adjusting The Customer Lcd Screen
Tighten once correct angle is achieved. STEP 4 Adjust the LCD Customer Screen angle by loosening the 2x M6 Nyloc Nuts on the LCD Stand Arm 10mm Spanner supplied Tighten once correct angle is achieved. 15201-ML002 REV05 ECN 5847 Page 20... - Page 21 Chapter 9 - Customer LCD SCREEN performed by trained service personnel only. Adjusting the Customer LCD Screen STEP 5 Recheck Customer Screen angle & height. If further adjustment is required, repeat Steps 3 to 5. 15201-ML002 REV05 ECN 5847 Page 21...
-
Page 22: Replacing The Nfc Reader
STEP 4 Remove & retain 2x Nuts and 1x Bracket fastening the NFC Reader from the underside of the Top Lid. To re-install the replacement NFC Reader, follow Steps 1 to 4 in reverse. 15201-ML002 REV05 ECN 5847 Page 22... -
Page 23: Replacing The Customer Lcd Screen
STEP 2 Unplug 3x LCD Screen Loom plugs from the USB Hub. STEP 3 Loosen the 2x M8 Button Head Screws to remove the Customer Screen assembly. To re-install the replacement Customer LCD Screen, follow Steps 1 to 3 in reverse. 15201-ML002 REV05 ECN 5847 Page 23... -
Page 24: Replacing The Proximity Sensor
STEP 3 Unclip the Proximity Sensor from the retainer. Retainer STEP 4 Remove the Proximity Sensor from the Top Lid. Remove & replace the Proximity Sensor. To re-install the replacement Proximity Sensor, follow Steps 1 to 4 in reverse. 15201-ML002 REV05 ECN 5847 Page 24... - Page 25 CAUTION: Servicing of this product or unit is to be performed by trained service personnel only. 15201-ML002 REV05 ECN 5847 Page 25...