sisel ENDA EPDA1 Series Instructions

Read this document carefully before using this device. The guarantee will be expired by device damages if you don't attend to
the directions in the user manual. Also we don't accept any compensations for personal injury, material damage or capital
disadvantages.
ENDA EPDA1, ESDA1, EPGA1, EPAA1, ESAA1 Panel Mounted Solid State Relays
Thank you for choosing ENDA EPDA1 / ESDA1 / EPGA1 / EPAA1 / ESAA1 Series Solid State Relays
12-25-40-50-70-100-120A AC Load current.
(Varies by model type. Please check the order code).
320-480 AC Load voltage.
3-30V DC (for only EPxx), 8-30V AC/DC or 90-240V AC input voltage.
LED status indicator for input voltage.
Zero-cross or Random-cross at AC voltage.
Applicable for three phase loads.
Built-in varistor protection.
Panel or Narrow Panel mounted.
CE Marked according to European Norms.
ORDER CODE
EP D A 1
Product Basic Code
Panel Type
EP
Narrow Panel Type
ES
Input Voltage
3-30V DC G
D
8-30V AC/DC
A
90-240V AC
Load Voltage
AC A
Pole Number
Single-pole 1
ENVIRONMENTAL CONDITIONS
Ambient-storage temperature
Relative humidity
Pollution degree
Overvoltage category
Altitude
Protection
KEEP AWAY device from exposed to corrosive, volatile and flammable gases
or liquids and DO NOT USE the device in similar hazardous locations.
OUTPUT
Load voltage/ current
Load curent, AC51/25ºC (Arms)
Load voltage (Vrms)
Overload current t=1s/25°C (Arms)
Non rep.surge current/25°C (Arms)
On-state voltage drop (Vrms)
Leakage current (mArms)
I²t For fusing t=10ms (A²s)
Frequency (Hz)
Minimum operating current (mArms)
THERMAL SPECIFICATIONS
Tj Junction temperature (°C)
Rth(j-c)Junction-case thermal resistance (°C/W)
Rth(j-a)Junction-ambient thermal resistance (°C/W)
INPUT
Order code
Input voltage
Pick-up voltage
Drop-out voltage
Input current
Turn-on time
Turn-off time
LED indicator
GENERAL
Order code
Dimensions
Weight (After packaging)
Isolation voltage
Connection
Terminal screw torque
Product standard
Mounting
Enclosure material
Avoid any liquid contact when the device is switched on.
DO NOT clean the device with solvent (thinner, gasoline, acid etc.) and / or abrasive cleaning agents.
- 2 25 Z
Switching
Zero-cross Z
Random-cross
R
Load Current EPAA EPDA EPGA
12A AC 12 12
25A AC 25 25
40A AC 40 40
50A AC 50 50
70A AC 70 70
100A AC 100 100
120A AC 120 120
Load Voltage
24-320V AC 2
50-480V AC 4
-25... +60°C/-30 ... +100°C (without icing and condensation)
Relative humidity 90% for temperatures up to 20°C decreasing linearly to 50% relative humidity at 40°C.
2
II
Max. 1000m
IP20 According to EN60529
212 225
12 25
24-320
50 85
120
250
1,6
5
78
340
50-60
160
≤125 ≤125
≤125
≤ ≤
2,3 1,2 ≤
≤20 ≤20
EPGA1-xxxZ EPGA1-xxxR
3 - 30VDC
> 3VDC
< 2VDC
< 10mAdc
Max. ½ Period
Max. ½ Period
If input voltage is AC/DC >3V, LED lights up.
EPxA1-xxxZ EPxA1-xxxR
W45xH62xD31mm
EPxA1-2xx/4xxZ/R = 95g
EPxA1-550/570Z/R = 110g
EPxA1-5100/5120Z/R = 115g
2500Vrms between I/O terminals for 1 min.
For power line 16mm² (with cable terminal 25mm² ) cable, for signal line 4mm² cable can be connected.
For power line max. 2,2Nm, for signal line max. 1,2Nm.
EN 60947-4-3
Mounted to the panel by using M4 screws.
Self extinguishing plastics. (According to EN 60695-11-10 V-O)
ESAA ESDA
12 12 12
25 25 25
40 40 40
50
70
425 440
240
40
25 40
150
150
85
250 400
400
5 5
880
340
880
160
160
≤125
≤125
≤ ≤ 1,0
1,2
0,7
≤20 ≤20
≤20
ExDA1-xxxZ
8 - 30VAC/DC
> 6VAC/DC
< 2VAC/DC
< 17mAac/10mAdc
Max. ½ Period
Max. ½ Period
If input voltage is AC/DC >6V, LED lights up.
ESDA1-xxxZ ESDA1-xxxR
mm
W24xH101xD29
ESDA1-2xx/4xxZ/R = 95g
1/2
450 470
50 70
50 - 480
300
200
500 800
1,6
10 10
600 1600
50 - 60
200 320
≤125
≤125
≤
0,4
≤
0,6
≤20
≤20
ExDA1-xxxR ExAA1-xxxZ
If input voltage is AC/DC >75V, LED lights up.
ESAA1-xxxZ
W24xH101xD29
ESAA1-2xx/4xxZ/R = 95g
EPxA1-xxx-Z-EN-10-220103
4100
4120
100
120
540
720
1350
1800
1,8
20
20
9100
16200
500
500
≤125
≤125
≤ 0,3
≤ 0,25
≤20
≤20
ExAA1-xxxR
90 - 240Vac
> 75Vac
< 6Vac
< 8mAac
Max.1 Period
Max. 2 Period
ESAA1-xxxR
mm