Intended use Cleaning and maintenance . . . 22 Intended use Overall condition of the machine . . . 22 I n t e n d e d u s e Special salt and rinse aid ..22 This appliance is intended for Filters .
Safety instructions Keep children below the age of Installation 8 years old at a safe distance Following installation, ensure from the appliance and power that the back cable. of the dishwasher is not freely accessible (protection Before you switch ON the against contact due to hot appliance surface).
Page 6
Safety instructions If the dishwasher is installed Do not install the appliance below or above other near heat sources (radiators, domestic appliances, follow heat storage tanks, cookers the information for installation or other appliances which in combination with generate much heat) a dishwasher and install it under in the installation instructions...
Safety instructions In daily use Deactivating the button lock: Hold down the button + for Read and observe the safety information and instructions approx. 4 sec. until the for use on the packaging display goes out. for cleaning and rinsing agents. When the programme ends on the digital display), the Childproof lock (door lock)
Page 8
Safety instructions Keep children away from Warning detergents and rinse aid. Risk of injury! These may cause chemical Knives and other utensils burns in the mouth, throat with sharp points must be and eyes or asphyxiation. placed in the cutlery basket Keep children away from with the points open dishwasher.
Protection of the environment Protection of the Getting to know your environment appliance i o n P r o t e c t o f t e n v i r o n m e n t G e t t i t o k n o w y o u r a p p l i a n c...
Water softening system/Special salt To change the setting: Water softening 1. Press programme button 3. system/Special salt Each time the button is pressed, the set value increases by one level; W a t e r s o f t e n i s y s t e m / S p e c i s a l t when the value of :...
Rinse aid 1. Open the screw-type cap of the Switching off salt refill compartment 12. indicator/water softening 2. Fill the tank with water (only required system when switching on the appliance for S w i t c h i n g o f f w a t e r s o f t e n i n g s y s t e m the first time).
Rinse aid 1. Open the dispenser 1J by pressing 1. Close the door. and lifting the plate on the cover. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button H until : ..is indicated on the digital display.
Utensils Loading the dishwasher Utensils U t e n s i 1. Remove large food remnants. It is not necessary to prerinse utensils Not suitable under running water. 2. Place the utensils so that Cutlery and utensils made of wood. –...
Utensils B asket 1B Chopstick basket* B a s k e t C h o p s t i c k b a s k e t *depending on the model Chopsticks up to a length of 24 cm can be placed in the chopstick basket.
Detergent F olding spikes * Note F o l d i n g s p i k e s To ensure a good washing result, * depending on model always follow the instructions on the detergent packaging! The spikes can be folded down to If you have further questions, improve arrangement of pans, bowls we recommend that you contact...
Detergent 2. Close the cover on the detergent Combination detergent dispenser by sliding it up until the lock engages without difficulty. Apart from conventional detergents (Solo), a number of products are offered with additional functions. These products contain not only the detergent but also rinse-aid and salt replacement substances (3in1) and, depending on the combination (4in1, 5in1, etc.),...
Overview of programmes Overview of programmes p r o g r a m m e s O v e r v i e w o f The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options § Programme selection Half load * H a l f l o a d You can select a suitable programme If you have only a few items to wash according to the type of utensils and (e.g. glasses, cups, plates), you can degree of soiling.
Operating the appliance Switching on the appliance Operating the appliance 1. Turn on the tap fully. 2. Switch on ON/OFF switch (. O p e r a t i i a n c e t h e a p p l The Magic Daily programme display Programme data flashes.
Operating the appliance T imer programming * 1. Close the door. T i m e r p r o g r a m m i n g 2. Switch on ON/OFF switch (. 3. Hold down programme button # * depending on model and press START button H You can delay the start of the until : ...
Operating the appliance Interrupting the programme Intensive drying 1. Switch off ON/OFF switch (. The final rinse uses a higher temperature which improves the drying The LEDs go out. The programme is result. The running time may increase saved. slightly. (Caution if utensils are delicate!) If the door was opened on an appliance which has a warm water 1.
Cleaning and maintenance Never use a steam cleaner to clean your Cleaning and dishwasher. The manufacturer is not liable for any consequential damage. maintenance Regularly wipe the front of the appliance C l e a n i a n d n a n c e m a i n t e and fascia with a damp cloth;...
Cleaning and maintenance Filters Spray arm The filters 1* keep large foreign Limescale and dirt from the rinsing objects in the rinsing water away from water may block nozzles and the the pump. These foreign objects may bearing assemblies of the spray arm 1".
Fault, what to do? In this case: Fault, what to do? 1. First disconnect the appliance from F a u l t , w h a t d o ? the power supply. Experience has shown that you can 2. Remove the filters 1*. rectify most faults which occur in daily 3.
Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display P lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min.
Page 26
Fault, what to do? Fault Cause Remedial action A different error code is A technical fault has probably Switch off appliances with the ON/OFF switch (. After a short time restart indicated on the digital occurred. display. the appliance. to : If the problem recurs, turn off the tap and pull out the mains plug.
Page 27
Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid in Refill rinse aid. the dispenser. Programme selected without Select programme with drying (see drying. Overview of programmes, Programme sequence). Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
Page 28
Fault, what to do? Fault Cause Remedial action Food remnants Utensils placed too closely Arrange utensils with adequate clearance on the utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
Page 29
Fault, what to do? Fault Cause Remedial action Washable or water-soluble Detergent substances are Change detergent brand. coatings in the container deposited. These coatings cannot Clean appliance mechanically. or on the door. usually be removed with chemicals (appliance cleaner, ...). If there is a “white coating”...
Page 30
Fault, what to do? Fault Cause Remedial action Coloured (yellow, orange, Film formation consisting Check function of the water softening brown), easily removable of ingredients from food system (refill with salt) or, if using combined deposits inside remnants and substances from detergents (tablets), activate water the appliance (mainly the tap water (limescale), “soapy”...
Page 31
Fault, what to do? Fault Cause Remedial action Rust spots on the cutlery. Cutlery not adequately rust- Use corrosion-resistant cutlery. resistant. Knife blades are frequently more severely affected. Cutlery will also rust if rusting Do not wash rusting parts. parts are rinsed at the same time (pan handles, damaged utensil baskets, etc.).
Page 32
Fault, what to do? Fault Cause Remedial action Filling valves making Depends on domestic installation, No remedial action possible. striking noises. as appliance is not defective. No effect on appliance function. Knocking or rattling noise. If there is a low load, the water Load the appliance with more utensils jets strike the washing tank or distribute the utensils more evenly...
Customer service Customer service Installation and connection C u s t o m e r s e r v i c e If you are unable to rectify the fault, l a t i o n I n s t a l a n d c o n n e c t i please contact your customer service.
Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions can thoroughly in the factory to ensure that it be found in the installation instructions. is in working order. This may cause Level the appliance. Ensure that the small water stains.
Installation and connection Drinking water connection Warm water connection * W a r m w a t e r c o n n e c t i o n 1. Fasten the drinking water connection * depending on model to the tap according The dishwasher can be connected to the installation instructions using to cold or hot water up to max.
Installation and connection Electrical connection Transportation Connect the appliance to an Empty the dishwasher and secure loose alternating current only, ranging from parts. 220 V to 240 V and 50 Hz or 60 Hz Drain the appliance according to the via a correctly installed socket with following steps: protective earth conductor.
Page 38
*9000972761* 9000972761 en (9702) 550MA...
Need help?
Do you have a question about the SK Series and is the answer not in the manual?
Questions and answers