Before Starting The Equipment - EINHELL TE-TC 620/1 U Original Operating Instructions

Operating mode S6 20%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 20% of the cycle at the
specifi ed rating and must then be allowed to idle
for 80% of the cycle.
Sound and vibration
The noise emission values were measured in ac-
cordance with EN 62841-1.
With-load operation
L sound pressure level ........................ 72 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 85 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
The quoted total vibration value and the
quoted noise emission value were measured in
accordance with standardized test procedures
and can be used to compare one electric tool with
another.
The quoted total vibration value and the quoted
noise emission value can also be used to make
an initial assessment of exposure.
Warning:
•
The vibration and noise emission levels
during actual use may vary from the values
quoted, depending on the way in which the
electric tool is used and, in particular, on the
type of workpiece being processed.
•
For the operator's protection it is essential
to specify safety measures based on an
estimate of the exposure to vibrations during
the actual conditions of use (all stages of the
operating cycle must be considered in this
connection, e.g. times in which the electric
tool is OFF and times in which the tool is ON
but operating without load).
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_TE_TC_620_1_U_SPK7.indb 19 Anl_TE_TC_620_1_U_SPK7.indb 19
GB
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a
work bench, the base frame supplied in deli-
very, or similar.
•
All covers and safety devices must be cor-
rectly attached before the machine is used for
the first time.
•
The cutting wheel must rotate smoothly.
Unfolding the base frame (Fig. 2)
To set up the equipment on its feet (1), press the
latching button (a) and lower the respective feet
(1) until they latch in the intended position. To fold
up the feet (1), proceed in reverse order.
Fitting the cooling water pump (Fig. 4 - 6)
First place the container (a) for the cooling water
pump (13) in the intended position on the trough
(3).
Place the cooling water pump (13) - with the suc-
tion cups pointing down - into the container (a).
Then fasten the hose to the intended positions as
shown in Fig. 5 and 6.
Notice!
To guarantee proper operation, the cooling water
hose (14) must not be kinked during installation.
- 19 -
24.01.2022 08:26:23 24.01.2022 08:26:23