Table of Contents
Advertisement
Quick Links
Power Supply Unit
DR-ID 1200MP
Operation Manual
2nd Edition : April 2016
897N120970A
This Operation Manual describes details on how to operate the power supply unit
DR-ID 1200MP and cautions to be observed when operating it.
Please read the Operation Manual, System Operation Manual and other manuals
for the related products before actually operating the power supply unit.
After reading this manual, store it nearby the power supply unit so that you can see
it whenever necessary.
For Safe Operation
System
Configuration
(Product Overview)
Basic Operation
Daily Inspection and
Maintenance
Appendix
Maintenance and
Inspection
Advertisement
Table of Contents
Related Manuals for FujiFilm DR-ID 1200MP
Summary of Contents for FujiFilm DR-ID 1200MP
- Page 1 Inspection This Operation Manual describes details on how to operate the power supply unit DR-ID 1200MP and cautions to be observed when operating it. Please read the Operation Manual, System Operation Manual and other manuals for the related products before actually operating the power supply unit.
- Page 2 897N120970A DR-ID 1200MP Operation Manual...
- Page 3 Introduction The power supply unit DR-ID 1200MP is a device which supplies power to the flat panel sensor and connects between the flat panel sensor, image processing unit and control cabinet. The power supply unit DR-ID 1200MP is an optional item of DR-ID 1200.
- Page 4 Source codes for certain type of open source software used in this product are available at delivery cost. If you would like to receive such source codes, please contact FUJIFILM dealer or the service representatives at the agency from which you purchased this product. (Please be noted that any inquiries concerning the contents of source codes should be directed to original licensors of open source software.)
-
Page 5: Table Of Contents
Changing the Direction of the Flat Panel Sensor Connector ........3-2 3.1.4 Checking the Connection between the Flat Panel Sensor and the Connector ..3-2 Starting Up and Shutting Down the DR-ID 1200MP ..........3-2 3.2.1 Starting Up the DR-ID 1200MP ................3-2 3.2.2... - Page 6 897N120970A DR-ID 1200MP Operation Manual...
-
Page 7: Chapter 1 For Safe Operation
For Safe Operation Chapter 1 1.1 Safety Before using the DR-ID 1200MP, read this section thoroughly to ensure that you use the product properly. Electric Shock Warnings and Cautions WARNING The power supply to this device is AC100 to 240V. - Page 8 Because this equipment is not explosion-proof, do not use combustible and explosive gases near the equipment. WARNING Flammable gasses may stay in the room after disinfection. If you turn the system on just after disinfection, ensure that the room is well ventilated before powering on the system. 897N120970A DR-ID 1200MP Operation Manual...
- Page 9 If any of the following occurs, immediately turn off the power of each unit, unplug the power cable from the outlet, and then contact our official dealer or FUJIFILM Representative. ● When smoke, strange odor, or abnormal sound is present.
- Page 10 Category 5 cable (CAT 5E) or higher are appropriate for connection to this connector. CAUTIONS After connecting this system to the network with other systems,confirm that the other systems are not affected. If they are affected, take countermeasures such as network separation. 897N120970A DR-ID 1200MP Operation Manual...
- Page 11 System Isolation Instructions WARNING To ensure complete system isolation, never install any unauthorized items. When it is necessary to install authorized optional items, contact our official dealer or FUJIFILM Representative. WARNING Keep the products other than those used for patients out of their reach to ensure appropriate system isolation.
- Page 12 No modification of this equipment is allowed. CAUTIONS Install the system in accordance with what is provided by IEC 60601-1:2005 + A1:2012 Chapter 16. Contact our official dealer or FUJIFILM Representative for installation (except the flat panel sensor) of the system. CAUTIONS Do not hit or drop the equipment.
-
Page 13: Chapter 2 System Configuration (Product Overview)
2.1.1 System Configuration DIGITAL RADIOGRAPHY DR-ID 1200 Flat panel sensor unit Flat panel sensor Power supply unit DR-ID 1200MP Control cabinet DR-ID 1200MC Image processing unit DR-ID 300CL* • The products in can be installed in patient environment. • Up to two flat panel sensors can be connected to one power supply unit in wired communication mode. -
Page 14: Unit Names And The Functions
Power status LED Displays ON/OFF of the power supply unit. 2.3 Locations of Labels and Signs Locations of labels and signs affixed to the DR-ID 1200MP, and the relevant safety signs are shown below. 2.3.1 Locations of Labels Do Not Step On... -
Page 15: Safety And Other Symbols
At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about waste, please contact our official dealer or FUJIFILM Representative. Year of manufacture Refer to Instruction Manual/Booklet... -
Page 16: Symboles De Sécurité Et Autres
Votre coopération pour la mise au rebut correcte de ce produit contribuera en outre à une utilisation efficace des ressources naturelles. Pour en savoir plus sur les déchets, contactez notre revendeur agréé ou notre représentant FUJIFILM. Année de fabrication Consultez le mode d’emploi... -
Page 17: Chapter 3 Basic Operation
When multiple fl at panel sensors are used, make sure that the READY lamp among the status lamps of the fl at panel sensor to be used for an exposure is lit. Connect/Disconnect the connector straight to the fl at panel sensor. If connected/disconnected at an angle, the connector may be damaged. 897N120970A DR-ID 1200MP Operation Manual... -
Page 18: Changing The Direction Of The Flat Panel Sensor Connector
Press the ON side of the main switch of the power supply unit. Make sure that the power status LED is lit in blue. Start up the flat panel sensor with the initial settings properly made by our official dealer or FUJIFILM Representative. 3.2.2 Performing an Exposure When performing an exposure, make sure that the READY status lamp on the flat panel sensor is lit. -
Page 19: Chapter 4 Daily Inspection And Maintenance
4.1 Daily User Inspection and Maintenance During maintenance and inspection, strictly observe precautions contained in “Chapter 1 For Safe Operation” in this manual for you to use the DR-ID 1200MP under best conditions. 4.1.1 Periodical Inspection Inspection Every Three Months... - Page 20 897N120970A DR-ID 1200MP Operation Manual...
-
Page 21: Appendix A Specifications
Specifications Appendix A A.1 Specifications Specifications of the DR-ID 1200MP are shown below. A.1.1 Power Supply Conditions Rated voltage : 100-240V~ Input current : 2-0.84A Frequency : 50-60Hz A.1.2 Environmental Conditions (1) Operating Conditions Temperature : 15°C (15%RH) - 30°C (80%RH) Humidity : 15%RH (15°C) - 80%RH (30°C) (no dew condensation) -
Page 22: External View And Weight
A.2 External View and Weight The external view and weight of the DR-ID 1200MP are shown below. Specifications, dimensions and weight are subject to change for improvement without prior notice. A.2.1 DR-ID 1200MP Width Depth Height Weight (mm(in.)) (mm(in.)) (mm(in.)) -
Page 23: Appendix O Use Of Optional Items
This item is a set of anchor and a fixture, which is used for securing the power supply unit to the floor. Retaining Bracket for MP Retaining Bracket for MP Identification Label Contact a FUJIFILM dealer for installation of the Retaining bracket for MP. 897N120970A DR-ID 1200MP Operation Manual... -
Page 24: Relay Unit For Ac Bucky
This item consists of the relay and terminal block used for connecting the AC bucky. Relay Unit for AC Bucky AC Bucky Relay UNIT 100-110V AC Bucky Relay UNIT 110-120V Rating Label Rating Label AC Bucky Relay UNIT 200-220V AC Bucky Relay UNIT 220-240V Rating Label Rating Label 897N120970A DR-ID 1200MP Operation Manual... -
Page 25: Maintenance And Inspection
(Number of exposures : 90,000) The cycles of periodical maintenance and inspection and of parts replacement differ depending on the usage and the daily operation time. For details, contact our official dealer or FUJIFILM Representative. 897N120970A DR-ID 1200MP Operation Manual... - Page 26 FUJIFILM MEDICAL SYSTEMS U.S.A., INC. 419 WEST AVENUE, STAMFORD CT 06902, U.S.A.
Need help?
Do you have a question about the DR-ID 1200MP and is the answer not in the manual?
Questions and answers