Table of Contents
Advertisement
Quick Links
User Manual
For
802.11 b/g/n Draft 2.0 Intelligent NIC Card
(Ralink RT3662)
Model Number : WMP-N13
Revision: 1.2
This document contains confidential proprietary information and is the property of Alpha Networks Inc.. The contents of
this document may not be disclosed to unauthorized persons without the written consent of Alpha Networks Inc..
Alpha Networks Proprietary and Confidential Information
Advertisement
Table of Contents
Related Manuals for Alpha WMP-N13
Summary of Contents for Alpha WMP-N13
- Page 1 Model Number : WMP-N13 Revision: 1.2 This document contains confidential proprietary information and is the property of Alpha Networks Inc.. The contents of this document may not be disclosed to unauthorized persons without the written consent of Alpha Networks Inc..
- Page 2 New released • 2009/12/17 Amanda Wang Revise 11n HT20/40 Receiver Sensitivity • 2010/3/9 Amanda Wang Revise Block Diagram , 11b/g/n Transmitter Output • Power and receiver sensitivity numbers Revise Operating temperature / non-operating • temperature Alpha Networks Proprietary and Confidential Information...
- Page 3 WMP-G15 Test Manual Install WinPcap 1. Run WinPcap_4_0_2.exe to install the WinPcap tool. 2. Insert the WMP-N13 card and turn on the test board. 3. Confirm the Ethernet link speed is 1000Mbps. Run Test Utility 1. Run “RT3882QA.exe” to start test tool.
- Page 4 2. Select your Giga Ethernet adapter. 3. Start to TX/RX signal testing. Select channel. b. Select mode. Select data rate. d. Select bandwidth. Select TX/RX path. Start to transmit signal. Alpha Networks Proprietary and Confidential Information...
-
Page 5: Table Of Contents
2.4.3 Security ................................11 2.5 M ..........................11 ECHANICAL EQUIREMENTS 2.6 C ........................... 11 OMPATIBILITY EQUIREMENTS 2.7 R ..............11 EQUIREMENTS OF ELIABILITY AINTAINABILITY AND UALITY 2.8 E ......................... 11 NVIRONMENTAL EQUIREMENTS I: ..........................錯誤! 尚未定義書籤。 PPENDIX Alpha Networks Proprietary and Confidential Information... -
Page 6: Requirements
Rate and at room Temp. 25degree C 18(±2dBm at 1,2,5.5,11Mbps 2.2.2.8 Receiver Sensitivity Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate = –80 dBm at 1Mbps –80 dBm at 2Mbps –76 dBm at 5.5Mbps –76 dBm for 11Mbps Alpha Networks Proprietary and Confidential Information... -
Page 7: Ieee 802.11G Section
GI=400ns 2.2.3.5 Data Rate 20MHz 40MHz 20MHz 40MHz 13.5 14.4 19.5 40.5 21.7 28.9 43.3 57.8 58.5 121.5 65.0 72.2 14.444 28.889 43.333 57.778 86.667 115.556 130.000 144.444 19.5 40.5 21.7 43.3 58.5 121.5 Alpha Networks Proprietary and Confidential Information... -
Page 8: General Section
Three UFL compatible antenna connectors 2.2.4.2 Operating Voltage 3.3VDC +/- 10% 2.2.4.3 Current 1.2 A Consumption 2.2.4.4 Form Factor and PCI-E connector with RGMII signal Interface 2.2.4.5 PCB Outline See below 2.2.4.6 Pin Assignment See below Alpha Networks Proprietary and Confidential Information... - Page 9 18 GND 19 GE_RXD0 20 GND 21 GND 22 GND 23 GE_RXCLK 24 GND 25 GND 26 GND 27 GND 28 GND 29 GE_TXD2 30 GND 31 GND 32 GND 33 GE_TXD1 34 GND Alpha Networks Proprietary and Confidential Information...
-
Page 10: Software Requirements
Set the number of bytes used for RTS/CTS boundary 2.4.2.6 Transmission Speed This indicates the communication rates. Select appropriate transmission speed to match your wireless LAN settings 2.4.2.7 Roaming Support Automatic or Manual Rescan to associate with access point. Alpha Networks Proprietary and Confidential Information... -
Page 11: Security
Wi-Fi Meet Wi-Fi certification for IEEE 802.11b/g/n product 2.6.2 WHQL Meet applicable WHQL certification requirements 2.6.3 Physical Layer and Meet ALPHA Engineering Test Plan and Test Report Functionality 2.7 Requirements of Reliability, Maintainability and Quality Feature Detailed Description 2.7.1 MTBF Mean Time Between Failure >... - Page 12 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio...
- Page 13 This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna, For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool.