Table of Contents
Advertisement
Quick Links
金輪牌工業用縫紉機
GOLDEN WHEEL INDUSTRIAL SEWING MACHINE
CS CS CS CS- - - - 2390
Read safety instructions carefully before operating
Keep this Instruction Manual for future reference
為了安全地使用，請你再使用之前一定閱讀本使用說明書
請你注意保管本使用說明書，以便隨時查閱
啟
翔
CHEE SIANG INDUSTRIAL CO., LTD.
CHEE SIANG INDUSTRIAL CO., LTD.
CHEE SIANG INDUSTRIAL CO., LTD.
CHEE SIANG INDUSTRIAL CO., LTD.
2390/CS
2390
2390
/CS- - - - 2391
/CS
/CS
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
股
份
2391
2391
2391
操作手冊
操作手冊
操作手冊
操作手冊
有
限
NO：CS-2390N01
公
司
Advertisement
Table of Contents
Related Manuals for CHEE SIANG INDUSTRIAL GOLDEN WHEEL CS-2390
Summary of Contents for CHEE SIANG INDUSTRIAL GOLDEN WHEEL CS-2390
- Page 1 Read safety instructions carefully before operating Keep this Instruction Manual for future reference 為了安全地使用，請你再使用之前一定閱讀本使用說明書 請你注意保管本使用說明書，以便隨時查閱 啟 翔 股 份 有 限 公 司 CHEE SIANG INDUSTRIAL CO., LTD. CHEE SIANG INDUSTRIAL CO., LTD. CHEE SIANG INDUSTRIAL CO., LTD. CHEE SIANG INDUSTRIAL CO., LTD.
-
Page 2: Table Of Contents
目錄索引 目錄索引 CONTENTS 目錄索引 目錄索引 CONTENTS CONTENTS CONTENTS PAGE PAGE PAGE PAGE ㄧ ㄧ ㄧ ㄧ ..機器使用 機器使用 機器使用 機器使用 HOW TO USE MACHINE HOW TO USE MACHINE HOW TO USE MACHINE ----------------------------------------- HOW TO USE MACHINE 1.部件名稱... -
Page 3: ㄧ ㄧ ㄧ ㄧ
ㄧ ㄧ ㄧ ㄧ ..機器使用 機器使用 機器使用 HOW TO USE MACHINE 機器使用 HOW TO USE MACHINE HOW TO USE MACHINE HOW TO USE MACHINE 1. 1. 1. 1.部件名稱 部件名稱 NAMES OF MAIN PARTS NAMES OF MAIN PARTS 部件名稱... -
Page 4: 線掛 Thread Guide
2. 2. 2. 2.線掛 線掛 線掛 線掛 THREAD GUIDE THREAD GUIDE THREAD GUIDE THREAD GUIDE 為了便於包裝，線掛已被取下，包裝好後放在了附件箱裡。請根據圖 Fig.1-2 所示安裝線掛。 For the convenient sake of packing, the thread guide is removed from the machine and packed separate in the accessory box. Put the thread guide as shown in Fig.1-2. 轉速... -
Page 5: 注油 Oiling
6. 6. 6. 6.注油 注油 注油 注油 OILING OILING OILING OILING 每天給機器加油十分重要。 It is most important the machine is properly oiled every day. 給每個加油處滴ㄧ兩滴油(Fig.4)。 One or two drops of oil would be supplied to all the spots indicated in the (Fig.4.) 7. -
Page 6: 如何穿線 How To Thread The Machine
如何穿線 HOW TO THREAD THE MACHINE HOW TO THREAD THE MACHINE 如何穿線 如何穿線 HOW TO THREAD THE MACHINE HOW TO THREAD THE MACHINE 8.如何穿線 從線掛(1)開始穿起，按序穿過下列過到 Starting from the thread guide (1), please lead the thread as per the following manner. (2)三孔過線器... -
Page 7: 如何繞線 How To Wind Bobbin
9. 9. 9. 9.如何繞線 如何繞線 HOW TO WIND BOBBIN HOW TO WIND BOBBIN 如何繞線 如何繞線 HOW TO WIND BOBBIN HOW TO WIND BOBBIN 如果繞在梭心上的底線不均勻，就會影響縫製效果。請根據下列步驟認真繞線。 If the bobbin thread does not wind evenly on the bobbin, this will affect the stitch and please be careful to wind the thread to bobbin as per the following: 1)將梭心套上繞線軸。... -
Page 8: 調節面線鬆緊 Regulating The Thread Tension
11.調節面線鬆緊 調節面線鬆緊 REGULATING THE THREAD TENSION REGULATING THE THREAD TENSION 調節面線鬆緊 調節面線鬆緊 REGULATING THE THREAD TENSION REGULATING THE THREAD TENSION 面線和底線的鬆緊應調節ㄧ致，以便縫製的時候將兩根線鎖在面料中間。 For ordinary stitching, the tension of the upper and lower thread should be equal so as to lock both threads in the center of the fabric. -
Page 9: 二 二 二 二
二 二 二 二 ..機器調節 機器調節 機器調節 機器調節 ADJUSTMENT ADJUSTMENT ADJUSTMENT ADJUSTMENT 1. 1. 1. 1.直線調節 直線調節 ADJUSTMENT FOR STRAIGHT SEWING ADJUSTMENT FOR STRAIGHT SEWING 直線調節 直線調節 ADJUSTMENT FOR STRAIGHT SEWING ADJUSTMENT FOR STRAIGHT SEWING 機器出廠時人字調節鈕都是設置在”0”位 置。... -
Page 10: 人字調節 Adjustment Of Zigzag Movement
3. 3. 3. 3.人字調節 人字調節 ADJUSTMENT OF ZIGZAG MOVEMENT ADJUSTMENT OF ZIGZAG MOVEMENT 人字調節 人字調節 ADJUSTMENT OF ZIGZAG MOVEMENT ADJUSTMENT OF ZIGZAG MOVEMENT 如果人字凸輪運行錯誤，可將機針運行至最低點，然後擰緊凸 輪上的調節螺絲(E)至最高點。(Fig.11) In case the zigzag drive cam is found wrongly situated, make the needle to reach its lowest point and tighten the set screw “E” of the cam to come to the top, as shown in the (Fig.11). -
Page 11: 運行至最低點時的機針差動調節 Adjustment Of Needle Timing At Its Lowest Position
5. 5. 5. 5.運行至最低點時的機針差動調節 運行至最低點時的機針差動調節 運行至最低點時的機針差動調節 運行至最低點時的機針差動調節 ADJUSTMENT OF NEEDLE TIMING AT ITS LOW ADJUSTMENT OF NEEDLE TIMING AT ITS LOW ADJUSTMENT OF NEEDLE TIMING AT ITS LOWEST POSITION ADJUSTMENT OF NEEDLE TIMING AT ITS LOW EST POSITION EST POSITION EST POSITION 移開面蓋，鬆開針棒座上的螺絲。慢速轉動手... -
Page 12: 三 三 三 三
三 三 三 三 ..故障排除 故障排除 故障排除 故障排除 TROUBLE SHOOT TROUBLE SHOOT TROUBLE SHOOT TROUBLE SHOOT 發生下列故障，請參照說明的方法予於排除。(*重要，**十分重要) If following problems be occurred, please check the points as suggested below. (*marked be checked carefully, **marked be most carefully checked) 斷線...
Need help?
Do you have a question about the GOLDEN WHEEL CS-2390 and is the answer not in the manual?
Questions and answers