Jay's Audio CDT3-MK3 User Manual

Jay's Audio CDT3-MK3 User Manual

Hide thumbs Also See for CDT3-MK3:

Advertisement

JAY'S AUDIO
CDT3-MK3
USER MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CDT3-MK3 and is the answer not in the manual?

Questions and answers

Summary of Contents for Jay's Audio CDT3-MK3

  • Page 1 JAY’S AUDIO CDT3-MK3 USER MANUAL...
  • Page 2: Package Contents

    Audio Precision APX525 before shipping. Careful installation of the product will ensure the correct performance and ensure the product is at its full potential. PACKAGE CONTENTS 1. CDT3-MK3 2. AC Mains Power Cord 3. Disc Clamp 4. Gloves 5.
  • Page 3 QUICK START GUIDE 1. After receiving the CDT, please do not rush to power it up. First, check the physical appearance of any damage may be caused by shipping. 2. Slide the top loading lid open and remove the protection foams completely. 3.
  • Page 4: Front Panel

    FRONT PANEL Figure 1. CDT3-MK3 Front Panel POWER button --- To make the CDT to standby status or to normal operation. When CDT is standby, a blue LED will be lit on in the centre screen. PAUSE button --- Pause CD playback.
  • Page 5: Real Panel

    REAL PANEL Figure 2. CDT3-MK3 Rear Panel (1) POWER SWITCH ---- Power On/Off the CDT unit by using the power switch. There is no standby function. (2) AC MAINS IEC ---- Connect the power cord to the AC Mains IEC inlet firmly. The AC Mains is fitted with a mains fuse, rated at 1.6A, 5x20mm, Slow Blow.
  • Page 6 Figure 3. HDMI- I2S Pinout Figure 4. RJ45- I2S Pinout...
  • Page 7 There is no industry standard of I2S connection. We could not guarantee the I2S connection workability with your DAC. This shall not be considered as a defect should the matching failed. List of verified and tested DACs:  JAY’S AUDIO DAC2-SE ...
  • Page 8: Remote Control Unit

    REMOTE CONTROL UNIT The CDT3-MK3 comes with a milled solid aluminum Remote Control Unit. It is a generic Remote Control equipped for all CDT/CDP products; hence, it is not all the buttons are functional with the CDT3-MK3  Power  Turn on/standby the CDT ...
  • Page 9: Operation

    The connections of power cord, interconnect cables are located at the rear panel of the CDT. For both safety and performance, please use quality cable from reputable suppliers. i.e. Studio Grade cable, namely, Gotham / Sommer Cable / Mogami / Belden, etc. OPERATION Figure 6. CDT3-MK3 Top Loading...
  • Page 10  Disc Loading To open the CDT3-MK3 top loading door, slide the lid towards the rear of the unit fully. The CDPRO2 assembly shall be visible, and the Disc Clamp shall be accessible. Lift the Disc Clamp gently by holding the center part of the Disc Clamp. Place a disc to the center of the disc holder.
  • Page 11  10MHz reference clock signal input and output  176.4KHz 24bit up-sampling circuit.  HDMI-I2S LVDS and LAN-IIS LVCMOS Output.  Highest quality materials and audio-grade components  Full CNC Milled Aluminium Chassis. Figure 7. Internal of CDT3-MK3 (Upper part)
  • Page 12 SPECIFICAITON  Digital Output o Output Sampling Rate 16 Bit / 44.1KHz or 24 Bit / 176.4KHz o Coaxial RCA/BNC 2Vrms, 75ohm o AES/EBU 5Vrms, 110ohm o HDMI-I2S LVDS / RJ45-I2S LVCOMS  Reference Clock Input/Output: 10MHz / 0.3 – 5 V p-p / 50 to 75 Ω ...

Table of Contents

Save PDF