Philips 55P9161 Quick Start Manual page 3

TV
T
ELEVISION BEGIN
1
button to turn the TV ON.
WABC
MENU
VOL CH
Remote Sensor STATUS/EXIT
Window
R
EMOTE
B I BEGIN
ATTERY NSTALLATION
1
T
o load the supplied bat-
teries into the remote:
"System" button on the
remote
1. Remove the battery
sends its commands to the TV.
compartment lid on the
back of the remote. Point the remote control
toward the remote sensor win-
2. Place the batteries (2-
dow on the TV when operating
AA) in the remote. Be
the TV with the remote.
sure the (+) and (-) ends
of the batteries line up
correctly (inside of case is
marked.)
3. Reattach the battery lid.
A/V Button
Press to quickly select Auxiliary source
inputs on the TV (AUX1 VIDEO; AUX2
VIDEO; etc.), as well as Antenna A/B inputs,
and the last viewed channel on the TV.
Guide Plus+ Buttons
Press to use the Guide Plus+ electronic guide
for TV program listings and information.
TV-VCR-ACC "S "
YSTEM
Refer to your separate Guide Plus+ informa-
B tion manual for setup and use details.
UTTONS
The remote's TV-ACC-VCR
TV-ACC-VCR System Buttons
System buttons control how
Press to send remote signals to either the TV or
buttons on the remote are
accessory VCRs, Cable TV Converters, Laser
used.
Disc players, etc.
For example:
Sleep Button
Press to set the TV to automatically turn itself
With the "TV" system but-
Off. Press the Sleep button repeatedly to
ton pressed:
select the amount of time (15 minutes to 2
the Menu ring buttons
hours) before the TV shuts Off.
and (+,-) buttons are used
to select and adjust on-
Menu Select Buttons
screen TV features.
Press the Menu Select button to show on-
screen controls. Press the outer Menu ring
With the "VCR" system
button to move up and down (or left and
button pressed:
right) through the list of on-screen controls.
the Power, Channel, and
Press the center Menu ring button to select
other dedicated VCR
and access highlighted controls.
buttons (see remote's flip
Status/Exit Button
down door) are used to
select and adjust VCR Press to see the current channel number on
the TV screen. Also press to clear the TV
model features.
screen after control adjustments.
With the "ACC" system
Volume Buttons
button pressed:
Press to adjust the TV sound level up (+) or
the Power, Channel
down (-).
Number, and Channel
Up /Down buttons on
Mute Button
the remote can work with
Press to turn the sound OFF on the TV. Press
Cable TV Converters,
again to return the sound to its previous level.
Laser Disc players, and
100+ Button
Home Satellite Dish
systems. Press to select channel numbers greater than
99 (by direct button entry). Press the 100 but-
ton then the remaining two digits to select the
Note: For more details on
desired channel.
how the TV remote works
with VCRs, Cable Converters,
VCR Buttons
and other accessory equip-
For use of VCR buttons see the "Using the
ment see the other owner's
Remote With a VCR" in your other owner's
manual supplied with your
manual.
TV.
All manuals and user guides at all-guides.com
R C
AND EMOTE
2
Press the VOLUME UP
Press the POWER
(+) or DOWN (-) buttons to
adjust the TV sound level.
2
1
Press the TV
to be sure the remote
STOP
S H
MART ELP
can press any button on
the front of the TV to
turn the TV ON.
O
ONTROL PERATION
3
Press the CHANNEL UP
( ) or DOWN ( ) button to
select TV channels.
Note: Always press two number
buttons on the remote when
selecting channels.
For example: press "0" then "6"
for channel 6.
MENU
VOL CH
3
STATUS/EXIT
1
Press the Backlight button to illuminate or
light the remote's buttons to make them easier to
read and use in dark room conditions.
AV POWER
GUIDE INFO
TV VCR ACC
SWAP PIP CH SOURCE FREEZE
DN UP
AUTO
SLEEP
STATUS/ MENU/
EXIT SELECT
VOL
CH
MUTE
1 2 3
4 5 6
7 8 9
0
100+ SURF
VCR
REC
RESET
PLUS+
CLEAR
Open the remote control VCR button
area with the pull tabs located on both
sides of the hinged door.
Remember, You
The tuned channel number will
always briefly appear when the
TV is first turned ON (and with
channel changes.)
3
S
MART
H
ELP
Note: You
can press any of the
TV's front keyboard
buttons to turn the
TV ON, but the
Power button must
be used to turn the
set OFF (from the
STOP
TV's local key-
board).
3
Power Button
Press to turn the TV (or select VCR,
Cable Converters, etc.) ON and OFF.
PIP Buttons
Press to operate Picture-In-Picture fea-
tures. See "PIP" section in your other
owner's manual for details.
Auto Button
Press to select from a list of Auto con-
trols. Auto Picture for factory preset
picture control levels (set for different
types of viewing sources and pro-
grams.) Auto Sound to select various
audio mode settings matched to differ-
ent types of TV programming. Auto
Surf to quickly select up to 10 chan-
nels (separate from the TV's normal
channel scan memory). See the "Auto
Features" section in your other owner's
manual for details.
Channel Scan Button
Press to scan up (+) or down (-)
through programmed channel num-
bers.
Number Buttons
Press the number buttons to select TV
channels. Press two number buttons to
select single digit channels. For exam-
ple: press "0" then "6" for channel 6.
Surf Button
Press to select previously viewed
channels. With the TV's "Auto Surf"
control ON you can place up to 10
channels in memory. Then by pressing
the SURF button you can quickly view
the select channels.
See the "Auto Surf" section (in your
other owner's manual) to see how to
select a series of channels using the
Surf button.
You can also press the STATUS
button (on the remote) to see
what channel the TV is ON.