Related Manuals for Genie W3500S
Summary of Contents for Genie W3500S
- Page 1 Point to Point / Multi-Point 3km IP Bridge W3500S User Manual Please read these instructions carefully before operating the unit and keep for further reference.
-
Page 2: Table Of Contents
Contents 1.0 Introduction ......................3 1.1 Product Features ...................3 1.2 Package Contents ..................3 1.3 Specification....................4 2.0 Configure Connections ..................5 2.1 Set-Up Diagram ....................6 2.2 LAN Access ....................7 2.3 Device A Configuration................7 2.4 Device B Configuration ................8 2.5 Using Schematic ..................9... -
Page 3: Introduction
All examples and pictures used here are for reference only. The contents of this manual are subject to change without notice. The Genie W3500S is a 5G wireless outdoor CPE with the next generation 802.11a/n Wi-Fi standard. Up to 300Mbps high speed data transmission and equipped with two 10/100m LAN ports, the W3500S achieves data transmission over the air for point-to-point and point to multi-point connections up to 3km transmission distance. -
Page 4: Specification
User Manual Point to Point / Multi-Point 3km IP Bridge 1.3 Specification Chipset AR9344 Dram DDR2 64MB Flash Interface 10/100Mbps LAN x2 11a:54M,48M,36M,24M,18M,12M,9M,6Mbps Data Rate 11n:7.2M,14.4M,21.7M,28.9M,43.3M,57.8M,65M,72.2M,14.4M, Functions 28.9M,43.3M,57.8M,86.7M,115.6M,130M,144.4Mbps 433Mbps Transmission Mode DSSS Modulation Mode OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK Wireless Standard IEEE802.11a, IEEE802.11n ,IEEE802.3u CSMA/CA,TCP/IP,IPX SPX, NetBEUI, DHCP, NDIS3, NDIS4, Protocol NDIS5... -
Page 5: Configure Connections
2.0 Configure Connections Digital Bridge-A Master Mode (IPC Receiver) PoE Adapter Swicth Computer Camera (Usually near NVR) Digital Bridge-B Slave Mode (IPC Transmitter) LED Light Round Light PoE Adapter Swicth Computer Camera (At the IPC End) First set A-B mode DIP switch, the LED L will appear and start blinking. After the L dis- sappears, it will show the selected configuration. -
Page 6: Set-Up Diagram
User Manual Point to Point / Multi-Point 3km IP Bridge A IP B IP 2.4 ID 5.8 ID 192.168.255.100 192.168.255.200 192.168.255.101 192.168.255.201 192.168.255.102 192.168.255.202 192.168.255.103 192.168.255.203 192.168.255.104 192.168.255.204 192.168.255.106 192.168.255.205 192.168.255.106 192.168.255.206 192.168.255.107 192.168.255.207 192.168.255.108 192.168.255.208 192.168.255.109 192.168.255.209 192.168.255.110 192.168.255.210 192.168.255.111 192.168.255.211 192.168.255.112... -
Page 7: Lan Access
User Manual Point to Point / Multi-Point 3km IP Bridge 2.2 LAN Access After powering on the radio, connect LAN2 port to the PC network port and configure IP address and subnet mask to 192.168.255.xxx 2. Open your browser and input the login IP address of the device (if the device is A, enter “http:/ /192.168.255.1”, if the device is B, enter “http:/ /192.168.255.2”) and press enter to login to the WEB management interface. -
Page 8: Device B Configuration
User Manual Point to Point / Multi-Point 3km IP Bridge 2.4 Device B Configuration Login to the interface of [Bridge Set] 2. Bridge mode is set to mode B 3. Set the ID number (the ID number of device B should be the same as device A) 4. -
Page 9: Using Schematic
User Manual Point to Point / Multi-Point 3km IP Bridge 2.5 Using Schematic One-to-one configuration is used for connection between two devices. 2. One-to-many configuarion is used for connection between one device A and multiple device B (Up to 4 at no more that 60 degrees apart). - Page 10 Sales +44(0)1707 330541 Enquiries sales@genieproducts.co.uk Website www.genieproducts.co.uk...