Related Manuals for Genie WONVR216P5
Summary of Contents for Genie WONVR216P5
- Page 1 16 Channel H.265 Optimised NVR with 2HDD Bays WONVR216P5 Quick Start Guide Please read these instructions carefully before operating the unit and keep for further reference.
- Page 2 Intro Section Please read this instruction carefully before operating the product and keep it for further reference. All examples and pictures used here are for reference only. The contents of this manual are subject to change without notice. This device should be operated only from the type of power source indicated on the marking label.
-
Page 3: Table Of Contents
Contents 1.0 Introduction ......................4 1.1 Product Features ...................4 1.2 Product Dimensions ..................4 1.3 Specification....................5 2.0 HDD Installation ....................6 3.0 Rear Panel Instruction ..................7 4.0 Start Up and Shut Down ..................8 5.0 Login ........................9 6.0 Configurations and Connections ................10 6.1 Network Configuration & Adding IP Camera ..........10 7.0 UPnP ........................12 8.0 NAT ........................13 9.0 Manual Recording and Playback .................14... -
Page 4: Introduction
1.0 Introduction The Genie ‘Optimised’ WONVR216P5 network video recorder is a 16 channel PoE NVR with resolution on every channel of up to 5MP. There are 16 PoE ports available, 2 bays for hard drives and this versatile NVR fully supports up to 16 channels of simultaneous playback. -
Page 5: Specification
Quick Start Guide 16 Channel H.265 Optimised NVR with 2HDD Bays 1.3 Specification Model WONVR216P5 System Embedded Linux Network Input 16 CH IPC input Network Access Format 5MP / 4MP / 3MP / 1080p / 960p / 720p @ 25 / 30fps... -
Page 6: Hdd Installation
2.0 HDD Installation This series of the product supports 2 SATA hard drives. Please make sure that the device is powered off before the installation. The pictures of the installation are for reference only. Loosen the screws to open the cover. 2. -
Page 7: Rear Panel Instruction
3.0 Rear Panel Instruction The interfaces of the rear panel are for reference only. AUDIO AUDIO DC48V PoE Ports Internet... -
Page 8: Start Up And Shut Down
4.0 Start Up and Shut Down Startup Connect the monitor and the power. 2. The device will boot and the power indicator will display blue. 3. A wizard window will pop up. Shutdown Click “Start” and then select “Shutdown” icon. This will bring up a shutdown window. The device will shut down by clicking “OK”... -
Page 9: Login
5.0 Login The default username is admin and the default password is 123456. You must configure the wizard if you start the NVR for the first time and you may change the password when you configure the wizard for the first time. You can skip the settings wizard next time. Click “Start”... -
Page 10: Configurations And Connections
6.0 Configurations and Connections 6.1 Network Configuration & Adding IP Camera After you finish adding IP cameras, you can see the live images through the monitor of the NVR. The following will mainly introduce how to add the IP cameras via LAN/WAN. Set the network of the NVR. - Page 11 Quick Start Guide 16 Channel H.265 Optimised NVR with 2HDD Bays 5. Checkmark the device you want to add and then click “Add” button. The NVR will automatically refresh the cameras and return to “Edit Camera” interface. “Online” status means connecting the device successfully and you will see the live image. You may select the added device and click button to modify channel, IP address, etc.
-
Page 12: Upnp
7.0 UPnP You can use the UPnP function to enable the fast connection of the device to WAN via a router without port mapping. Go to Start → Settings → Network → UPnP, and enable UPnP and then click “Apply” button to save. -
Page 13: Nat
8.0 NAT NAT Settings The NVR shall be powered on and connected to the network. 2. Go to Start → Settings → Network → TCP/IP. You can obtain the IP address, subnet mask and gateway automatically. You can also manually enter them according to the actual network situation. -
Page 14: Manual Recording And Playback
9.0 Manual Recording and Playback 9.1 Manual Recording Before recording, please install and format a HDD. In the live interface you can see the menu toolbar. Click button to start recording. Click it again to stop recording. You can also click to check the status of the recording. - Page 15 Sales +44(0)1707 330541 Enquiries sales@genieproducts.co.uk Website www.genieproducts.co.uk...