Sony KV-14FV1B Service Manual page 9

Changing The Programme Order Of The
TV Channels
The "Programme Sorting" option in the "TV Set Up" menu allows you to change
the order in which the channels (TV Broadcast) appear on the screen.
To do that: by using the menu system and after selecting the option, press
proceed in the same way as in the section "Switching On the Video TV and
Automatically Tuning" (see step 5b) on page 6).
Manually Tuning The TV
The "Manual Programme Preset" option in the "TV Set Up" menu allows you to
preset channels one by one to the programme order of your choice. To do that:
1 By using the menu system and after selecting the "Manual Programme Preset"
option, press . Then with Programme option highlighted press
to select on which programme number you want to preset the channel. Then press
.
2 After selecting the Channel option, press . Then press
channel tuning ("C" for terrestrial channels or "S" for cable channels). Next press
After that, press the number buttons to enter directly the channel number of the TV
Broadcast. If you do not know the channel number, press
When you tune the desired channel, press OK twice to store.
• Repeat all the above steps to tune and store more channels.
Fine Tuning Channels
Normally the Automatic Fine Tuning (AFT) is operating, however by using the
"Manual Programme Preset" option in the "TV Set Up" menu you can manually
fine tune the Video TV to obtain a better picture reception in the case that the
picture is distorted.
To do that: while watching the channel (TV Broadcast) you wish to fine tune, and by
using the menu system select the "Manual Programme Preset" option. Press
the AFT option highlighted, press . Next press or to adjust the fine tuning
between -15 and +15. Finally press OK twice to store.
Skipping Programme Positions
The "Manual Programme Preset" option in the "TV Set Up" menu allows you to
skip any unwanted programme numbers when they are selected with the PROGR
+/- buttons.
To do that: by using the menu system and after selecting the "Manual Programme
Preset" option, press . Then with the Programme option highlighted press
press or to select the programme number you want to skip. Press
the Skip option and press . Next press or to select Yes. Finally press OK twice
to confirm and store.
• To cancel this function afterwards, select "No" instead of "Yes" in the step above.
Setting Pay-TV Channels
The "Manual Programme Preset" option in the "TV Set Up" menu allows you to
watch Pay-TV channels by connecting a Pay-TV decoder to the Scart connector
:1/
placed on the rear of the Video TV.
To do that: by using the menu system and after selecting the "Manual Programme
Preset" option, press . Then with the Programme option highlighted, press
press or to select the programme number with the scrambled channel and press
. Select the Decoder option and press . Next press or
press OK twice to confirm and store.
• While you are recording a programme which is being recorded through the Pay-TV decoder, you will not
be able to view other programmes through the decoder.
8
TV Operation
Programme Sorting
Programme: 01 -> 01
and then Confirm:
Select channel: PROG + -
Select new position:
OK
. Press or
Manual Programme Preset
Programme: 01
or to select the
System: I
Channel: C 21
AFT:
On
.
Skip: No
Decoder: Off
Confirm
or to search for it.
OK
Manual Programme Preset
Programme: 01
System: I
Channel: C 21
AFT: On
Skip: No
Decoder:
Off
Confirm
. With
OK
. Next,
Manual Programme Preset
. Then, select
Programme: 01
System: I
Channel: C 21
AFT: On
Skip: No
Decoder: Off
Confirm
OK
Manual Programme Preset
. Next
Programme: 01
System: I
Channel: C 21
AFT: On
Skip: No
Decoder:
to select On. Finally, Off
Confirm
OK
Selecting The Language Of The Menu
Screens
The "Language" option in the "Set Up" menu allows you to select the language
that the menus are displayed in.
To do that: by using the menu system and after selecting the option, press
proceed in the same way as in the section "Switching On the TV and Automatically
Tuning" (see page 6, step 2).
Locking The Video TV
The "Parental Lock" option in the "Set Up" menu allows you to lock the buttons of
the Video TV set. In this way, after this option is selected and the Video TV set is
switched off, the buttons on the Video TV only works by using the remote control
buttons.
To do that: by using the menu system and after selecting the option, press
press or to select On. Press OK to confirm and store and finally press
• To cancel this function afterwards, select "Off" instead of "On" in the step above.
• If you have locked your Video TV and the remote commander is lost, press the
than 5 seconds) on the set to operate it.
Adjusting The Picture Rotation
(only for KV-21FV1U)
Because of the earth's magnetism, the picture might be slant. In this case, you can
correct the pictures slant by using the option "Picture Rotation" in the "Set Up"
menu.
To do that: by using the menu system and after selecting the option, press
press or to correct any slant of the picture between -5 and +5 and finally press OK
to store.
Switching On The Video TV
Automatically (On Timer)
The "On Timer" option in the "Timer" menu allows you to preset your Video TV
to automatically switch on at a desired time. You can select the TV programme or
video playback to be switched automatically on from standby mode.
To do that: by using the menu system and after selecting the option press
1 With Time option highlighted, press . Press or to set the on-time hour then
press . Proceed in the same way to set the minutes and press OK.
2 With Source option highlighted, press . Then press or
be switched on ("TV" or "VCR"). If you select "TV", press
to select the programme number you want the Video TV turns on. Press OK.
3 With On Timer option highlighted, press and then press
Press OK.
4 Finally press the standby button . At the selected time, the Video TV switches on
automatically.
• Any loss of power will cause these settings to be cleared.
• By pressing the ON TIMER button on the remote control you can set on/off the On Timer, but it is not
possible to change the time and programme settings.
Switching Off The Video TV
Automatically (Sleep Timer)
You can automatically switch the video TV into standby mode after a selected time
period.
To do that: Press the SLEEP button on the remote control repeatedly to set the time
period delay (OFF, 30, 60 or 90 minutes).
• While watching the TV, you can press the / button on the remote control to display the time
remaining.
• One minute before the Video TV switches itself into standby mode, a good night message will be displayed
on the screen.
• To cancel this function afterwards, select "Off" in the step above.
Set Up
TV Set Up
VCR Set Up
and then Language
Parental Lock: Off
VHS: Others
Picture Rotation: 0
OK
Set Up
. Then
TV Set Up
VCR Set Up
.
Language
Parental Lock: Off
VHS: Others
Picture Rotation: 0
button (during more
OK
Set Up
TV Set Up
VCR Set Up
Language
. Then Parental Lock: Off
VHS: Others
Picture Rotation: 0
OK
,
On Timer
Time: 06: 00
Source: TV PROG01
On Timer: Off
to select the source to
and then press or
OK
or to select On.
TV Operation
GB
9