Advertisement
INSTALLATION GUIDE
MADDOX Wall Organizer
PART A:
INSTALL PREPARATION
STEP 1: Space horizontal bars (H) with channel facing up
Horizontal Bars
s
10-24 Screws
Allen key 2.5mm
A
0-24 Screws
Allen key 2.5mm
10-24 Screws
Allen key 2.5mm
Allen Key 2.5 mm
(included)
STEP 1: Space horizontal bars (H) with channel facing up
G
A
Vertical Bars
End Caps
1/2`` Drill bit
Leveler
B
C
1/2`` Drill bit
1/2`` Drill bit
Allen Drill Bit 3mm
1/2" Drill Bit
(included)
I
H
STEP 1: Space horizontal bars (H) with channel facing up
6"
Toggler
Toggler
D
Leveler
Leveler
Leveler
(included)
J
STEP 1: Space horizontal bars (H) with channel facing up
A
Posts
10-24 Screws
Posts
#10-24 Screws
F
E
If installing on
partition replace
F with #8 wood
screw
Toggler
Toggler
Jig K
Jig L
(Shop Supplied)
K
L
A
Allen key 2.5m
WARNING:
This product can
expose you to
chemicals including
chromium (hexavalent
compounds), which
are known to the
State of California to
cause cancer and
birth defects or other
reproductive harm.
For more information,
visit
www.p65warnings.
ca.gov
Recommended but
not required
PART F
Refer to
for
placement
Page 1
Advertisement
Table of Contents
Related Manuals for TAG HARDWARE MADDOX
Summary of Contents for TAG HARDWARE MADDOX
- Page 1 INSTALLATION GUIDE MADDOX Wall Organizer PART A: INSTALL PREPARATION STEP 1: Space horizontal bars (H) with channel facing up Posts 10-24 Screws Allen key 2.5m Horizontal Bars Vertical Bars End Caps Toggler Posts #10-24 Screws WARNING: 10-24 Screws Allen key 2.5mm...
- Page 2 STEP 3: Insert End caps (E) into channel on horizontal bars (H). Tighten set screws while pushing End cap. PART B: ASSEMBLY STEP 3: Insert End caps (E) into channel on horizontal bars (H). Tighten set screws while pushing End cap. STEP 4: Insert aligning Jig 1 (J1) into the channel on the horizontal bar (H).
- Page 3 step 4: Detail 1 step 4: Detail 1 PART C: ASSEMBLY & WALL INSTALLATION step 4: Detail 1 step 4: Detail 1 STEP 8: Use Jig 2 (J2) to align End caps (E) with each other. Tighten all remaining screws on Vertical bar (V2) while pushing horizontal bars (H) down. Secure corners of Top view...
- Page 4 oduce togglers into the drilled holes and fix posts using 10-24 screws. PART D: WALL INSTALLATION STEP 13: Locatel frame using post intalled on last step. Level frame and mark wall by pressing on the remaining posts. STEP 13: Locatel frame using post intalled on last step. Level frame and mark wall by pressing on the remaining posts. ep 8 STEP 11: Locate frame on wall, mark hole drilling location to wall and drill hole using 1/2`` drill bit.
- Page 5 PART E: AVAILABLE SIZES & SUGGESTED CONFIGURATIONS HORIZONTAL BARS 13.5” 23” 35” 47” VERTICALS 19” 42” 66” Page 5...
- Page 6 PART F: Jig L Positioning Jig1 Standard use scheme dard use scheme tandard use scheme Jig1 Standard use scheme 13 1/2 inch 23 inch 35 inch 47 inch /2 inch 13 1/2 inch 23 inch 23 inch 23 inch 35 inch 35 inch 35 inch 47 inch...
- Page 7 Leave Behind Imitation Leather Care Instructions 1. Standard cleaning: wipe clean with a slightly damp cloth. Do not use highly acidic or alkaline cleaners, other non-recommended commercial cleaners or polishes, or treated cloths that have been used to clean other furniture. Do not steam or use heat. 2.
- Page 8 (Both screws) 3 complete turns 2.5 mm counter clockwise. (Both screws) Turn clockwise until tight. (Both screws) MADDOX Shoe Hooks|300.8218.xxx & 300.8219.xxx 3 complete turns counter clockwise. (Both screws) Shoe Hook 3 complete turns Turn clockwise counter clockwise. until tight.
Need help?
Do you have a question about the MADDOX and is the answer not in the manual?
Questions and answers