Makita VR001G Instruction Manual
Cordless concrete vibrator
Hide thumbs
Also See for VR001G:
- Instruction manual (89 pages) ,
- Instruction manual (87 pages) ,
- Instruction manual (64 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita VR001G
Summary of Contents for Makita VR001G
- Page 1 INSTRUCTION MANUAL Cordless Concrete Vibrator VR001G VR003G Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: VR001G VR003G Vibrations per minute Normal mode 12,000 min Power mode 15,500 min Vibration head diameter ø32 mm * Supplied as optional accessories ø32 mm Flexible shaft lengths 1.2 m / 2.4 m (Country specific) * Supplied as optional accessories 1.2 m - 2.4 m... -
Page 3: Safety Warnings
The typical A-weighted noise level determined accord- For European countries only ing to EN60745-2-12: The EC declaration of conformity is included as Annex A Model VR001G to this instruction manual. Sound pressure level (L ) : 80 dB(A) Uncertainty (K) : 3 dB(A) - Page 4 Personal safety Power tool use and care Stay alert, watch what you are doing and use Do not force the power tool. Use the correct common sense when operating a power tool. power tool for your application. The correct Do not use a power tool while you are tired or power tool will do the job better and safer at the under the influence of drugs, alcohol or med- rate for which it was designed.
- Page 5 Do not use a battery pack or tool that is dam- 15. If the power is cut off due to power failure aged or modified. Damaged or modified batteries or the disconnection of power plug, set the switch to the off position. may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
-
Page 6: Functional Description
Open the standard equipped battery case while causing fires, personal injury and damage. It will pressing the buttons on sides of the case. also void the Makita warranty for the Makita tool and Loosen the screws securing the standard charger. -
Page 7: Installation
Installation Slide an optional battery case into the tool. Open the case while pressing the buttons on sides of the Open the battery case while pressing the buttons case. Then tighten the screws to secure it in place. on sides of the battery case. Fig.4 ►... - Page 8 Uninstallation Open the rubber sealing grommet in the battery case. Make sure to squeeze the rubber sealing grommet out of Open the battery case while pressing the buttons the round hole rim from inside the front cover of the case. on sides of the battery case.
-
Page 9: Overdischarge Protection
Uninstallation Indicator lamps Remaining capacity Open the battery case while pressing the buttons on sides of the battery case. Lighted Blinking Open the rubber sealing grommet in the battery 75% to 100% case. Make sure to squeeze the rubber sealing grommet out 50% to 75% of the round hole rim from inside the front cover of the case. -
Page 10: Mode Selector
Charge the battery(ies) or replace it/them with recharged battery(ies). Let the tool and battery(ies) cool down. If no improvement can be found by restoring protection system, then contact your local Makita Service Center. Switch action Fig.14 CAUTION: Before installing the battery car- ►... -
Page 11: Electronic Function
Hold the drive shaft in the tool still using the NOTE: The mode you select will be saved automat- wrench provided. Then hand thread the end fitting of the ically when the tool is powered off. The tool restarts flexible core shaft onto the solid drive shaft in the tool. in the same mode as it previously used when turned on again. -
Page 12: Operation
If the coupling does not reach or fit securely onto the CAUTION: Be sure to attach the hooks of the male thread of the tool, especially when installing a long shoulder strap to the tool securely. If the hooks are flexible shaft, pull the outer casing further towards the attached incompletely, they may come off and cause tool while hand-turning the flexible core shaft so the... -
Page 13: Maintenance
To maintain product SAFETY and RELIABILITY, Fig.26 repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 13 ENGLISH... -
Page 14: Optional Accessories
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. - Page 16 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885974A220 www.makita.com 20220113...