1. Manuals
  2. Brands
  3. Demon International Manuals
  4. Washer
  5. Hurricane E
  6. Operation manual

Demon International Hurricane E Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operations Manual
Demon Battery E Range
Hurricane E
Tornado E Bowser
Tornado E Mini-Bowser
Including electric start variants and bowser washers
Declaration of Conformity
(E.H.S.R.)
We, Demon International Limited of Abbots Close, Lee Mill Industrial Estate,
Ivybridge, Devon, PL21 9GA, declare that this machine must be operated in
accordance with the operation and safety instructions as supplied with this
machine.
This machine is manufactured in accordance with the following standards
and recommendations.
HSE PVB PM29 - BS5415 Part - BS5415 Section 2.4 1986
This instruction manual is relevant only to the following machine and will not
be kept updated unless specifically requested by the customer. However,
any changes to the operating procedure or changes which might affect the
safety of this machine will be notified to the registered owner
Machine Type
Serial Number
Working Pressure
Date of Supply
Rev 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hurricane E and is the answer not in the manual?

Questions and answers

Related Manuals for Demon International Hurricane E

Summary of Contents for Demon International Hurricane E

  • Page 1 Including electric start variants and bowser washers Declaration of Conformity (E.H.S.R.) We, Demon International Limited of Abbots Close, Lee Mill Industrial Estate, Ivybridge, Devon, PL21 9GA, declare that this machine must be operated in accordance with the operation and safety instructions as supplied with this machine.

  • Page 2: Technical Specifications

    Technical Specifications Hurricane E Tornado E Bowser Motor 24 Volt DC Motor 24 Volt DC Pump XT 11/14 Pump XT 11/14 Pressure 1120—1500 PSI Pressure 1120—1500 PSI Flow 11 lpm Flow 15 lpm Nozzle 2504 Nozzle 2504 Battery 135amp sealed Lithium...
  • Page 3 Fault Finder FAULT CAUSE REMEDY Machine stops suddenly Low oil Check and top up oil Or will not start. Flat Battery (Electron ) Re-charge Water supply failed. Check water supply. Sudden pressure loss. No chemical Check chemical drum, close valve HP nozzle worn or un- Replace HP nozzle.
  • Page 4 Minimum Service Schedules DAILY CHECK THE FOLLOWING Oil level - top up as required. Battery percentage - top up as required. All hose unions for leaks- replace O rings if leaking. Hose condition - cuts etc. EVERY 500 HOURS OR SIX MONTHS (WHICHEVER COMES FIRST) Drain and replace pump oil.

  • Page 5: Operation

    Preparation Water Supply: Ensure there is an adequate water supply either from the mains or mini bowser tank. Attach water supply hoses to suitable tap or immerse the suction hose with approved suction filter into the reservoir. NOTE: ONLY CLEAN WATER SHOULD BE USED. THE PUMP MAY BE DAMAGED IF DIRTY OR CONTAMINATED WATER IS ALLOWED TO PASS THROUGH THE PUMP.
  • Page 6 Operate lance trigger Release residual pressure in gun and lance by operating trigger. Charging The E range is fitted with an indicator light which will glow green. Batteries MUST NOT be fully discharged before re-charging to maximise life cycles of the batteries.
  • Page 7 Tornado Mini Bowser E General Arrangement Tank Lid TOR0116 Lid Seals TORO1115 Hose Reel MTM20021 Tank TOR0113 Unloader ARMM4B/C Filter MTM85002 Pressure Gauge 15 mtr Hose HH00050MVGHR DEM20620 15 Mtr Hose HH00050MVGH ARXT11.14 Pump Brass Swivel MTM20060 O Rings MTM20024 Pump to hose reel hose Ball Valve BV12169...
  • Page 8 Hurricane - E General Arrangement Pressure Gauge Unloader DEM20620 ARMM4B/C ARXT11.14 Pump Stop/start Knob DEM102255 WHEEL400...
  • Page 9 Bowser E General Arrangement Hose Reel MTM20022 30 Mtr Hose HH00100MVGHR Jockey Wheel Pump to hose reel hose XLE00320 Unloader Minimatic 4/B ARXT11.14 Pump 24V DC Motor 200 amp 24V sealed battery...
  • Page 10 Charging When the machine requires charging please follow the instructions below. 1. Switch off the pressure washer. 2. Release the pressure in the lance. 3. Plug in the mains lead to 13 amp supply. 4. Charger should start on 24V Cold setting (if not set with the charge mode button) 5.

  • Page 12: Warranty

    Demon Internationals decision in warranty matters is final and binding. Demon International Ltd, undertake to repair or replace at their discretion, any component which may fail due to a manufacturing fault within a period of 12months from the date of purchase, provided that any fault or damage was not sustained by;...

  • Page 13: Warranty Procedure

    Warranty Procedure End Users If your machine develops a problem: 1. Phone Demon for advice with the model and serial number to hand. 2. Describe fully the problem as best you can. 3. If the problem cannot be resolved over the phone then the machine can be booked in for repair and if the faults are covered by the warranty the repair will be carried out free of charge.
  • Page 14 I can’t get the pressure to where it used to be — where do I start?
  • Page 17 XT 11/14 pump diagram...
  • Page 18 ARXT 11.14 XT 11/14 pump list...
  • Page 19 Minimatic 4/B unloader diagram...
  • Page 20 Minimatic 4/B unloader list...

  • Page 21: Ec Declaration Of Conformity

    EC Declaration of Conformity Demon International Ltd Abbots Close, Lee Mill Industrial Estate, Ivybridge, Devon PL21 9GA Declare that: Equipment High Pressure Water Jet Machines Model name/number Serial number Conforms to the relevant safety and health related requirements of the appropriate EC Directives. This decla- ration shall cease to be valid if modifications are made to the machine without our approval.

This manual is also suitable for:

Tornado e bowserTornado e mini-bowser

Table of Contents