Costway OP70368 User Manual
  1. Manuals
  2. Brands
  3. Costway Manuals
  4. Accessories
  5. OP70368
  6. User manual

Costway OP70368 User Manual

Hide thumbs Also See for OP70368:
Table of Contents

Advertisement

Quick Links

Download this manual
USER'S MANUAL
Retractable Awning
OP70368
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OP70368 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Costway OP70368

Summary of Contents for Costway OP70368

  • Page 1 USER’S MANUAL Retractable Awning OP70368 THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

  • Page 2: Before You Start

    Before You Start Please read all instructions carefully. Retain instructions for future reference. Separate and count all parts and hardware. Read through each step carefully and follow the proper order. We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
  • Page 3 1pc for backup 2pcs for backup 1pc for backup...

  • Page 4: Preparing Your Work Space

    Please prepare below tools before assembly. (Not included) Wrench Measuring tape Non-metallic mallet (wrenches of M17 and M14) Power drill with Cross screwdriver 14 mm drilling bit Two ladders or very sturdy chairs Preparing Your Work Space 1. Before you begin, it is best to lay out all necessary tools to make setup smoother.
  • Page 5 WARNING DO NOT remove the safety wrap that holds the awning arms down. Serious injury can result from removing the wrap too soon. 2. Open the awning box and unwrap each piece carefully to avoid damaging the product. 3. Lay out each piece of the awning to ensure that all pieces are present. Refer to the parts diagram for detailed information regarding parts.
  • Page 6 STEP 2 Connecting Front Bars 1. Insert the front bar(D2) into the interior end of the front bar(D1). If insertion is difficult, use a mallet to tap it into place. 2. Once inserted, fix it into place with screws(L) and tighten the screw nut on the bar.

  • Page 7: Step 3 Fabric Assembly

    STEP 3 Fabric Assembly 1. Open the fabric carefully to ensure that the product is not damaged. 2. Unfold both pieces of awning fabric.You should have one large fabric piece (F) and a valance with scalloped edge(G). 3. You should also have three fabric liner cords(H). 4.
  • Page 8 6. Roll the awning fabric counter clockwise around the roller tubes as tightly and evenly as possible. 7. Fix the bolt (J) on the hole of the roller bar (B1&B2)on the left& right side. Screw it tightly.
  • Page 9 8. Slide arm-bar link(K) into the groove of the front bar on the left side. Put the bolt(J) for fabric inserted,fix the bar end with a plastic cover(I-1). Then tighten the screw on the bolt. 9. Slide arm-bar link(K) into the groove of the front bar on the right side. Put the bolt(J) for fabric inserted,fix the bar end with a plastic cover(I-2).

  • Page 10: Specification

    Specification Material and Applicable wall Recommended Applicable Product name surface treatment type installation height weather Retractable Materials: Steel Reinforced 2.5m-3m The products tube, aluminum concrete walls, are used to awning alloy, plastic parts, brick walls shield sunshine. polyester fabric. Applicable when (Please see Service treatment: wind is under...
  • Page 11 STEP 4 Assembly awning on the wall Mark the position 1. Insert part O into A2 2. Connect A1 and A2 on the left and right side of the roller bar. 3. Measure the distance of product installation. 114.37inch/290.5cm 3.937inch /10cm 4.
  • Page 12 5. Mark the position on the wall Wall bracket leveled against horizontal line Wall bracket Wall bracket Level(horizontal line) 2.5-3m Ground 6. Drilling the bolt holes. Wall bracket leveled against horizontal line Wall bracket Wall bracket Level(horizontal line) Ground Ground...

  • Page 13: Preparing For Mounting

    Drilling the Bolt Holes Drill 8 cm deep 1. Now that you have a straight level line across the wall with the locations of the wall brackets and their bolt holes marked, you can drill holes to mount the brackets. 2.
  • Page 14 3. Make sure that the bolts are firm in place, yet let them stick out of the wall approximately 2.5 cm or less-enough that the wall bracket can be installed onto them. Firmly tighten the bolts with a 19 mm hex key. It is best to use the hex key with a closed end rather than an open end to avoid damaging the nut, should it slip.
  • Page 15 STEP 5 Assemble Arms WARNING Don't cut off the rope on the arm. 1. Assemble arm C1 on the wall bracket A1's arm holes. 2. Tighten the arm screws. 3. Assemble arm C2 on the wall bracket A2's arm holes. 4.
  • Page 16 5.Screw two plastic washers (M) into the arm-bar links (K). 6. Installation notes：Push C1 arms slightly in the direction of the fold and hold it. Move K to suitable position,make sure the K and the hole on the arm in the same vertical line.Then insert the arm-bar links to the holes on the end of both arms.
  • Page 17 7.Tighten the two screws and nuts with a wrench. (Installation notes: Do not fully tighten the screw nuts, leaving about 0.4cm space in between.) 8.Installation notes:Push C2 arms slightly in the direction of the fold and hold it. Move K to suitable position,make sure the K and the hole on the arm in the vertical line.Then insert the arm-bar links to the holes on the end of both arms.Then repeat step 7...
  • Page 18 When we have completed all the above steps, the product installation is complete. Please note: C1 and C2 arms are basically on the same parallel plane in their natural state...
  • Page 19 9.Please cut the straps on arms carefully while making sure that the cloth is completely tightened. 10. Open the awning with hand crank E. If you find that the cloth surface has fallen down. Please retract the cloth surface 3-5cm to ensure that the cloth surface is in a tight state.
  • Page 20 Attention! 1. Keep this product away from heat and flame. 2. Do not use this product in the rain or in strong winds. 3. Do not leave leaves or water too long on the roof. 4. Do not hang any clothes on any part of awning. 5.
  • Page 21 How to adjust the awning inclination The inclination of the awning is set by adjusting the screw WARNING when adjusting the awning inclination, please expand the awning completely Step1: Hold up the arm and loosen the screw （1&2） Don't loosen the screw directly without holding the arm Step2: Keep holding up the arm(C1)by your hand and adjust the screw(3) If you turn the screw in the direction of arrow a, the...
  • Page 22 Step1: Hold up the arm and loosen the screw(1&2) Don't loosen the screw directly without holding the arm up. Step2: Keep holding up the arm(C2)by your hand and adjust the screw(3) If you turn the screw in the direction of arrow a, the angle of the awning will go down.
  • Page 23 Replacements for missing or damaged parts will be shipped ASAP ! US office: Fontana UK office: Ipswich AU office: Truganina DE office: Hamburg FR office: Saint Vigor d'Ymonville PL office: Gdańsk Contact Us! US:cs.us@costway.com Do NOT return this item. UK:cs.uk@costway.com AU:cs.au@costway.com...

Table of Contents