Related Manuals for EOS LSG 10 CA
Summary of Contents for EOS LSG 10 CA
- Page 1 LSG 10 Contactor box LSG 10 CA / CW LSG 10 ET Installation and Operating Instructions Made in Germany IPx4 Print no. 29345277en / 26.22 Subject to technical changes...
- Page 2 Documentation Manufacturer EOS Saunatechnik GmbH Schneiderstriesch 1 D-35759 Driedorf, Germany Tel.: +49 (0)2775 82-0 Fax: +49 (0)2775 82-431 E-Mail: servicecenter@eos-sauna.com Web: www.eos-sauna.com Original installation instructions EN Copyright for these installation instructions remains with EOS Saunatechnik GmbH. Copyright as per DIN ISO 16016: The copying and distribution of this document, as well as the use and communication of its con- tents without express authorisation, are not permitted.
-
Page 3: Table Of Contents
Scope of delivery ............................9 Technical data ...............................9 Installation Installation site ........................... 10 LSG 10 CA / CW - installation details ...................11-15 LSG 10 ET - installation details ....................16-18 Electrical connections Board layout and overview of connections ................19 Terminals and connections ......................20 Recycling .............................. -
Page 4: General Safety Instructions
General safety instructions Safety levels Safety instructions and important operating instructions are classified. Please familiarise yourself with the following terms and symbols: WARNING Warning Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Caution Indicates a hazardous situation which, if not avoided, could result in minor or moderate in- jury. -
Page 5: Mounting And Electrical Installation
Mounting and electrical installation These installation instructions are intended for qualified personnel familiar with the laws and regulations applicable to electrical installations at the installation site. Observe the following general safety instructions during mounting, config- uration and commissioning of the product. Risk to life and limb and risk of fire Risk to life and limb from electric shock and fire in the event of improper or faulty electrical connection. -
Page 6: Operator Instruction
Damage due to incorrect mounting location The device is not suitable for outdoor use! It may be operated only inside buildings and may not be exposed to environmental condi- • tions such as extreme humidity and moisture or the possible formation of condensation or corrosive substances in the ambient air, as well as other weather conditions. -
Page 7: Standards And Regulations
For an overview of the standards that were observed during design and construction of the sauna heaters, please refer to the individual product‘s technical data sheet that can be downloaded from www.eos-sauna.com. Local regulations also apply to the installation and operation of heating, sauna, and steam... -
Page 8: Identification
Made in Germany S-No. 50.21 00002 EOS SAUNATECHNIK GmbH, Schneiderstriesch 1, 35759 Driedorf Intended use The LSG device in conjunction with a suitable control unit and a sauna heater control unit is intended to be used only to heat sauna cabins. It is suitable for cabins used in private and commercial settings. -
Page 9: Scope Of Delivery
10 kW Fuse protection (power supply) 3 x 16 A To be used with the control units EOS Econ, Compact, EmoTec, EmoStyle, EmoTouch 3 series Dimensions (H x W x D) 220 x 255 x 65 mm 270 x 190 x 90 mm Weight approx. -
Page 10: Installation Installation Site
Installation This chapter describes how to install the relay box, the control panel and the most important com- ponents. Cables to connect sauna heater, vaporizer (steam generator) or another heating system, light- ing(s), fan(s) or other components must have appropriate cross section. All electrical installations and all connecting lines that are installed inside a cabin must be suitable for an ambient temperature of at least 170°C and protection class IPx4 or be suitable for use in a steam room (IP 65). -
Page 11: Lsg 10 Ca / Cw - Installation Details
• Plant room or a similar suitable place If empty conduits for electrical installations are already present, this dictates the position of the relay box. LSG 10 CA/CW - Installation Guidelines WARNING Risk to life and limb and risk of fire Risk to life and limb from electric shock and fire in the event of improper or faulty electrical con- nection. - Page 12 Installation preparation 1. Determine the mounting site. 2. Route the lines. Removing the front cover Remove the front cover from the housing. • Unscrew the screw on the top of the housing. • Swivel the front cover and remove it downward. Notice: Remove the protective film from the panel after mounting is completed.
- Page 13 2. Insert and tigthen the upper screw, use dovel if necessary. Allow the screw to prot- rude approx. 3 mm so you can hook in the housing. 3. Prepare the line openinings in the housing by breaking the corresponding plates at the rear or at the bottom side.
- Page 14 7. Securely tighten the housing in the two lower mounting holes (B). 8. Connect power supply and consumers (see A oberes Befestigungsloch Electrical Installation). B untere Befestigungslöcher 9. Finally mount the front cover back on the control unit and secure it at the top with the mounting screw.
- Page 15 3. Prepare the line openinings in the housing by breaking the corresponding plates at the rear or at the bottom side. 4. Insert the supplied bushings into the pre- pared openings. 5. Draw the connection cables into the con- trol unit through these openings.. 6.
-
Page 16: Lsg 10 Et - Installation Details
LSG 10 ET - Installation Guidelines Proper and improper mounting of the control unit A Top mounting hole B Lower mounting holes... - Page 17 Installing the relay box Necessary steps: 1. Preparing for installation • Determine a suitable locati- on for the installation. • Route the lines. 2. Removing the housing cover (see Fig.) • Loosen 4 screws in the front cover panel. • Removing the housing cover 3.
- Page 18 4. Open the relay box conduits for the lines. 5. Insert supplied rubber grommets into the openings of the lower part of the housing.. 6. Route the connecting cables through the openings. A Lines with mains voltage, e.g. mains supply line, heat system, light B Connection line to sauna control unit 7.
-
Page 19: Electrical Connections
L1 L2 L3 N L1 L2 L3 N PE max. 10 kW max. 9 kW (10 kW*) Notice: Control unit shows only the ter- minals relevant for this connection. * 10 kW - for EOS Compact DP, HP, DC, HC... -
Page 20: Terminals And Connections
Terminals All lines must be connected to the corresponding terminals. Heat-resistant cables must be used for the sauna heater connection. WARNUNG Risk of electric shock A faulty electrical connection poses the risk of an electric shock. This risk remains also after com- pletion of the installation work. -
Page 21: Recycling
2012/19/EU. Do not dispose it with the normal household waste. Service Address: EOS Saunatechnik GmbH Schneiderstriesch 1 35759 Driedorf, Germany Tel: +49 (0)2775 82-514 Fax: +49 (0)2775 82-431 servicecenter@eos-sauna.de... -
Page 22: General Terms And Conditions Of Service
The manufacturers General Terms and Conditions of Business, which can be found at www.eos-sauna.com/ V. Liability agb, shall apply in addition to the foregoing terms and conditions of service.
Need help?
Do you have a question about the LSG 10 CA and is the answer not in the manual?
Questions and answers