Advertisement
Use caution when working into corners as contact with the intersecting surface may cause the grinder to jump or twist.
9
When grinding is complete allow the workpiece to cool.
9
6. MAINTENANCE
6.1.
Remove the battery before carrying out any adjustment, servicing or maintenance.
6.2.
There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free
of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.
7. TROUBLESHOOTING
7.1.
If your wheel wobbles or vibrates, check that clamping bolt is tight; check that the wheel is correctly located on the spindle.
7.2.
If there is any evidence that the wheel is damaged DO NOT use as the damaged wheel may disintegrate, remove it and replace with
a new wheel. Dispose of old wheels sensibly.
7.3.
If working on aluminium or a similar soft alloy, the wheel will soon become clogged and will not grind effectively.
7.4.
When overloaded, the motor comes to a stop. Relieve the load on the machine immediately and allow cooling for approx.
30 seconds at the highest no-load speed.
7.5.
When using as intended for the power tool cannot be subject to overload. When the load is too high or the allowable battery
temperature of 75 °C is exceeded, the electronic control switches off the power tool until the temperature is in the optimum
temperature range again.
7.6.
If machine is blocked, please turn ii off and turn ii on again after 1 ~2 seconds.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
This tool has been tested in accordance with: EN ISO 28927-1:2009 & BS EN ISO 15744:2008.
Declaration and verification of Vibration Emission figures are in accordance with EN 12096:1997
Measured vibration emission value (a): ............0.732 m/s²
Uncertainty value(k):.............................................1.50 m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that a
specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be
modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and
maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use and
Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSC website www.
hse.gov.uk - Hand-Arm Vibration at Work.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
WARNING! – RISK OF HAND ARM VIBRATION INJURY.
01284 703534
Original Language Version
sales@sealey.co.uk
www.sealey.co.uk
CP108VAGBO Issue 1 29/04/2021
Advertisement
