World Time - Casio 3206 Operation Manual

Operation Guide 3135 3206
Stopwatch
The stopwatch lets you measure elapsed time,
Hours
split times, and two finishes.
1/100 second
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from
zero after it reaches its limit, until you stop it.
• The stopwatch measurement operation
continues even if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is
frozen on the display clears the split time and
returns to elapsed time measurement.
• All of the operations in this section are
Minutes
Seconds
performed in the Stopwatch Mode, which you
enter by pressing D.
Current time
To measure times with the stopwatch
Elapsed Time
A A A
J J
Start Stop Re-start
Split Time
A C C
J J
Start Split Split release
(SPL displayed)
Two Finishes
A C A
J J
Start Split Stop
First runner Second runner
finishes. finishes.
Display time
of first runner.

World Time

World Time displays the current time in 33 cities
Current time in the zone
(29 time zones) around the world.
of the selected city code
• If the current time shown for a city is wrong,
City code
check your Home City time settings and make
the necessary changes.
• All of the operations in this section are
performed in the World Time Mode, which you
enter by pressing D.
To view the time in another city
In the World Time Mode, use A (east) and C
(west) to scroll through city codes (time zones).
• For full information on city codes, see the "City
Code Table".
Timekeeping
Mode time
To toggle a city code time between Standard Time and Daylight
Saving Time
1. In the World Time Mode, use A (east) and C
DST indicator
(west) to display the city code (time zone)
whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down E to toggle between Daylight
Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
• The DST indicator appears on the display
whenever you display a city code for which
Daylight Saving Time is turned on.
• You cannot toggle between Daylight Saving Time and Standard Time if the
displayed city code is UTC .
• Note that the DST/Standard Time setting affects only the currently
displayed city code. Other city codes are not affected.
Alarms
You can set five independent daily alarms. When
Alarm number
an alarm is turned on, the alarm tone sounds
when the alarm time is reached.
You also can turn on an Hourly Time Signal,
which will cause the watch to beep twice every
hour on the hour.
• The alarm number (AL1 through AL5)
indicates an alarm screen. SIG is shown when
the Hourly Time Signal screen is on the display.
• When you enter the Alarm Mode, the data you
were viewing when you last exited the mode
Alarm time
appears first.
(Hour : Minute)
• All of the operations in this section are
Current time
performed in the Alarm Mode, which you enter
by pressing D.
A C
J J
Stop Clear
A C
J J
Stop Clear
C C
J J
Split release Clear
Display time of
second runner.
To set an alarm time
Alarm on
1. In the Alarm Mode, use A and C to scroll
indicator
through the alarm screens until the one whose
time you want to set is displayed.
On/Off status
2. Hold down E until the hour setting of the alarm time start to flash, which
indicates the setting screen.
• This automatically turns on the alarm.
3. Press D to move the flashing between the hour and minute settings.
4. While a setting is flashing, use A (+) and C (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set
the time correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press E to exit the setting screen.
Alarm Operation
The alarm sounds in all modes at the preset time for about 10 seconds, or
until you stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down A to sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use A and C to select an alarm or the Hourly Time
Signal.
2. When the alarm or the Hourly Time Signal you want is selected, press B
to turn it on ( ON ) and off ( OF ).
Indicates alarm is ON.
Indicates Hourly Time Signal is ON.
• The alarm on indicator (
) and the Hourly Time Signal on indicator ( )
are shown on the display in all modes while these functions are turned on.
• If any alarm is on, the alarm on indicator is shown on the display in all
modes.
Illumination
Auto light switch The display of the watch is illuminated using an
on indicator
EL (electro-luminescent) panel for easy reading
in the dark. The watch's auto light switch turns on
illumination automatically when you angle the
watch towards your face.
• The auto light switch must be turned on
(indicated by the auto light switch on indicator)
for it to operate.
• See "Illumination Precautions" for other
important information about using illumination.
To turn on illumination manually
Press L in any mode to illuminate the display for about one second.
• The above operation turns on illumination regardless of the current auto
light switch setting.
• Illumination is disabled while configuring sensor measurement mode
settings, and during bearing sensor calibration.
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you
position your wrist as described below in any mode.
Note that this watch features a "Full Auto EL Light", so the auto light switch
operates only when available light is below a certain level. It does not
illuminate the display under bright light.
• The auto light switch is always disabled, regardless of its on/off setting,
when any one of the following conditions exists.
While an alarm is sounding
During sensor measurement
While a bearing sensor calibration operation is being performed in the
Digital Compass Mode
During tide data calculation
Moving the watch to a position that is parallel to the ground and then tilting
it towards you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
A
AL1 AL2 AL3
C
SIG AL5 AL4
More than
40 °
8