Page 1
SERVICE MANUAL 32D3200 MS82S-AP 1. Caution…………………………………………………………………………2 2. specification……………………………………………………………………6 3. Alignment Procedure…………………………………………………………7 4.Block diagram…………………………………………………………………1 5.Scheme Diagram …………………………………………………………… 5. Troubleshooting………………………………………………………………2 6. PCB Layout …………………………………………………………………3 This m anual i s t he l atest at t he t ime of pr inting, and doe s not include the modification which may be made after the printing, by the constant improvement of product...
Page 2
SCHNEIDER ELECTRONICS GMBH-GERMANY 1. CAUTION CA UTION: Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure. CA UT ION : T O RE DUCE TH E RIS K OF CA U T ION ELECTR ICA L SHOCK, DO NOT RE MOVE COVER (OR BACK).
Page 3
SCHNEIDER ELECTRONICS GMBH-GERMANY IMPORTANT SAFETY INSTRUCTIONS CAUTION: Read all of these instructions. Sa ve these instructions for later use . Follo w all W arnings and Instructions marked on the audio equipment. 1. Read Instructions-All the safety and operating instructionsshouldbe read before the productis operated. 2.
Page 4
SCHNEIDER ELECTRONICS GMBH-GERMANY PROTECTION AND LOCATION OF YOUR SET Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.
Page 5
SCHNEIDER ELECTRONICS GMBH-GERMANY OPERATION OF YOUR SET 18. This television set should be operated only from the type of power source indicated on the marking label.If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.
Page 6
EM BUSINESS CENTER FTV PRODUCT MANAGEMENT DEPT. SPECIFICATION RELEASE Version: V1.0 Issued Date: 2011.09.21 Model: L32D3200/MS82S-AP/SS3 PICTURE Category LCDTV Naturalight Technology Yes (Natural Light Engine ‖) Dynamic Contrast Color Temperature Warm / Normal / Cold SIGNAL FORMAT CAPABILITY Backlight Adjustable...
MS82S-AP/LA Chassis Software Upgrade Guidance Content 1. General Description 2. Factory Menu 2.1 Way of accessing 2.2 Factory Menu 2.3 ADC calibration menu 2.4 White Balance adjustment 3. Design Menu 3.1 way of accessing 3.2 SHOP Menu 3.3 Other Menu 3.4 Service Menu 3.5 PARAM SETTING MENU 3.6 Hotel Menu...
MS82S-AP/LA Chassis Software Upgrade Guidance General Description S82S-AP/LA is our latest design especially for LCDTV products selling in Asia Pacific (AP) and Latin America (LA) market. It features by its high integration, easy debugging as well as convenience in terms of maintenance. Fast software upgrade through USB disk facilitates both manufacture and after-sale service.
MS82S-AP/LA Chassis Software Upgrade Guidance 2.2 Factory Menu Factory Menu Name Default Description Status Factory Menu shortcut button switch HOTKEY The item must be disabled (OFF) after production WARM- OFF: Normal mode. Display blue screen when no signal. Turn to automatically standby mode if keep the signal unavailable over 15 minutes.
MS82S-AP/LA Chassis Software Upgrade Guidance 2.3 ADC calibration menu ADC Menu Press the button in remote control to select certain item and to change the value of ADC data or start ADC calibration. Notes: 1. Only YPBPR and RGB source should be calibrated. ADC Calibration menu Name Default...
MS82S-AP/LA Chassis Software Upgrade Guidance 2.4 White Balance Adjustment menu White Balance menu Press the button in remote control to select certain item and to adjust White Balance White Balance Adjustment menu Name Default Description Status Source Select the source you intend to apply WB adjustment. Only HDMI1, AV1, YPBPR, PC and should be adjusted.
MS82S-AP/LA Chassis Software Upgrade Guidance 3 Factory Main Menu 3.1 Accessing way: 1. In the first place, press Menu button of remote control, then select Contrast item of Picture submenu. Finally, press 1, 9, 5, 0 consecutively. 2. When the DESIGN HOTKEY item of Design Menu is enabled (ON), press Return button of remote control.
MS82S-AP/LA Chassis Software Upgrade Guidance 3.2 SHOP MENU Contain many options which can be chosen according to the requirements of customers as default settings when leave factory. Press the button in remote control to select certain item and to toggle among the available options..
MS82S-AP/LA Chassis Software Upgrade Guidance 3.3 Other Menu Press the button in remote control to select certain item and to toggle among the available options.. Other Menu Name Default Description Status VIF1 Exclusively used by R&D. VIF2 Exclusively used by R&D. VIF3 Exclusively used by R&D.
MS82S-AP/LA Chassis Software Upgrade Guidance MU1 DQS1 Manually adjust DQS1 phase of DDR1 Exclusively used by R&D ON: enable teletext OFF: Disable teletext 3.4 SERVICE MENU Press the button in remote control to select certain item and to toggle among the available options.. SERVICE MENU (Product Info) Name Default...
MS82S-AP/LA Chassis Software Upgrade Guidance ERROR CODE TCL_LOGO Display TCL Logo or not. On : display, Off: not display LOGO_LIGHT TCL_SHOW DEMO function ON/OFF 3.5 PARAM SETTING MENU Press the button in remote control to select certain item to enter menu.
MS82S-AP/LA Chassis Software Upgrade Guidance 3.6 HOTEL MENU Press the button in remote control to select certain item and to enter submenu. HOTEL MENU Name Default Description Status POWER LOGO select LOGO CH LOCK Channel scan lock. MAX VOL Max volume AUTO SET The switch of PIC, SOUND etc.
MS82S-AP/LA Chassis Software Upgrade Guidance 4. The steps of debugging 4.1 Device Color Analyzer CA-210. Video Pattern Generator Chroma2329. Color TV Pattern Generator PM5418, VGA cable, AV cable(RCA),YPBPR(RCA) cable. 。 Chroma2329 Fluke5418 CA-210 4.2 steps of debugging : According to the requirement of order, we suggest take the below steps to finish the appropriate settings.
MS82S-AP/LA Chassis Software Upgrade Guidance Ⅱ.steps of debug: 1) Access to the Factory menu->ADC 2) Select PC source 3) Select AUTO ADC,Press button in your remote control to calibrate the ADC automatically. 4) Select YPBPR source 5) Repeat step 3. 6) When the OK appears the calibration has been finished successfully.
Page 21
MS82S-AP/LA Chassis Software Upgrade Guidance 4) input white signal in 720p format 5) change R Gain and B Gain to make sure the value of color coordination equal to (x, y). 6) repeat step 2~5 until both of the value of color coordination of white and grey equal to (x, y).
4.5 ADC Calibration and White Balance Adjustment (automatic) The process of adjusting ADC and White Balance automatically is out of the range of this file. Please refer to the relevant technical file of HuiZhou factory of TCL 5. Chip list of software programming before SMT Following chips must be programmed before SMT by ALL-11 or other tools.
MS82S-AP/LA Chassis Software Upgrade Guidance Appendix: 1. Software upgrade through USB disk 1) Please ensure the software you are using has a correct file name TCL_MS82_UPDATE.bin, then copy it to the root directory of a USB disk. 2) Insert the USB disk to the USB socket of the set for which you are going to upgrade program.
MS82S-AP/LA Chassis Software Upgrade Guidance 2. Check software version, release date and Project ID After upgrading, sometimes you may not certain whether the new software has been successfully updated or not. In this case, you can check the software version and release date in Factory Main Menu to make sure the success of upgrading.
Page 25
MS82S-AP/LA Chassis Software Upgrade Guidance Product Information Check product information Remote Control name Power Supply name Audio Channel number Change project ID PRELIMINARY INFORMATION ----- SUBJECT TO CHANGE...
MS82S-AP/LA Chassis Software Upgrade Guidance 3. FAQ 1) Why there is no picture after upgrading software or changing project ID? It may be caused by fault of project ID. You can try below method to fix the problem. a. If the resolution of the panel of your set is 1366×768(HD panel), you can press Menu, and 4976 of remote control in series after turning on.
Page 27
Tuner I2C BUS U602 Earphone L/R Earphone AMP 13-DRV632-00B P603:47-EAR030-XX0 TU1_IF- IN TU1_IF- TUNER U601 L Channel TU1_IF+ Band Pass Filter AP:07-380FI5-NK4G TU1_IF+ IN Q601/Q602 Audio Amplifier Power R Channel LA:TBD Audio Amplifier 13-TPA311-D2B >32': 8W <26': 5W RF_AGC SPDIF OUTPUT VIDEO OUTPUT Q300/Q301 P305:47-RCA301-XB0G...
Page 28
01-MS82S0-MAC2XG MODEL: DESCRIPITION: DRAWN: DATE: CHECK: DATE: APPR: DATE: WW R&D CENTER TCL MULTIMEDIA TECHNOLOGY HOLDING LTD. 5TH FLOOR.TCL BUILDING.SOUTH NANHAI ROAD NANSHAN DISTRICT.SHENZHEN.GUANGDONG 518067 CHINA TEL:+86 755 33312403 ... NOTE: PAGE: FORMAT DIN A4...
Page 35
Trouble shooting 1、 Can not switch on: no switch on Check 3.3V/12V/24V of power supply Check PW Only 3.3V Check signal P—ON, Check DC-DC DIMBL—ON of main IC link part,check to PW Check the peripheral circuit of mail IC,check solder of Check reset Check IIC bus main IC,check data fo NVM...
Page 36
2、abnormal picture : Abnormal picture Individual signal source All signal source bad Check the path with this Check panel ID? signal source Check LVDS signal to main Check the peripheral circuit IC?check LVDS cable? of mail IC,updating SW,reset NVM,replace main IC Check crystal frequence?...
Page 37
3、 Abnormal sound: Abnormal sound Individual sound Check all sound signal source source Check the sound signal Check sound IC link to main IC Check the power of Check the peripheral Check wave filter and sound IC circuit of main IC,SW speaker?...
Page 39
H7-32D32E3-EGNB0AA 42-41316G-XX0G SPEAKER 16OHM 10W 82 200HZ RECTANGLE 20. H7-32D32E3-EGNB0AA 41-UK0150-0KK02 WIRE 2.6MM 0D2.6/7.8(9/0.10BC+S25/0.10BC H7-32D32E3-EGNB0AA 08-RC3000M-RM205AA RC300-EM伊朗/模拟电视/不带TCL LOGO遥控器 08-RC3000M-RM205AA 67-X89559-0E0 TV RAW SPRING RC200 BATTERY -ZF 00 00 R= FOR BACK CAB 08-RC3000M-RM205AA 67-X89558-0E0 TV RAW SPRING RC200 BATTERY -F 00 00 R=Y...
Page 40
40-EMRC30-RMB1XG TV PCB RM BD R=Y 08-RC3000M-RM205AA 25-HCL470-M1X CAP.ELE 2MM 47UF 16VV 5*7 85 \ 08-RC3000M-RM205AA 08-RC3000M-RM205Z RC300-EM伊朗/模拟电视/不带TCL LOGO遥控器 08-RC3000M-RM205Z 57-894200-0HA1A PAI DOOR RC300 BATTERY -- 00 -- 00 R=Y 08-RC3000M-RM205Z 57-894210-0HU1H DEC CABINET FRONT RC300 -- 00 -- 00 R=Y...
Page 53
08-MS82S01-MA300AA 19-GA0101-JTX SMD. RES 100 OHM 1/16W +/-5% R149 08-MS82S01-MA300AA 28-HB0470-JCX CAP.CER,SMD 47PF 50V 0402 - C648 08-MS82S01-MA300AA 25-TFB220-M1X CAP.ELE 5MM 22UF 50V 6.3 * 7 105 CD70H C637 08-MS82S01-MA300AA 13-MN6E18-2VB IC LCD TV MS82S CHASSIS SOC/MST6E182VS M U500 08-MS82S01-MA300AA 13-T6633E-00B IC 3 TO 1 HDMI SWITCH IT6633E-P U400...
Page 54
RAW SUPPORT STAND -- 00 00 00 R=N H7-32D32E3-EGNB0AA 62-919350-0UN RAW SUPPORT POWER -- 00 00 00 R=Y H7-32D32E3-EGNB0AA 58-L3232P-JKLAA PRI OVERLAY RATING LABEL-L32D3200 -- 00 H7-32D32E3-EGNB0AA 58-906090-JKL1R RAW OVERLAY SIDE AV (RIGHT) -- 00 00 00 H7-32D32E3-EGNB0AA 58-906080-JKL1T RAW OVERLAY SIDE AV (DOWN) -- 00 00 00 R...
Page 55
FROM MB P101 TO H7-32D32E3-EGNB0AA 46-FM040L-07P01G IR WIRE 400MM 7 A200 IR BOARD H7-32D32E3-EGNB0AA 70-STDD33-EEM1C TV PRI ADDENDUM SHEET D3300+19D3270 STAN H7-32D32E3-EGNB0AA 65-Z30050-23MG NUT-HEXAGON 3MM 2.3MM JIS B0209 WHITE ZN H7-32D32E3-EGNB0AA 66-890270-3E2 RAW HOLDER SCREW M3*3 -- 00 00 R=Y...
Need help?
Do you have a question about the L32D3200 and is the answer not in the manual?
Questions and answers