Framery Q Meeting Maggie Contents 1 Warranty checklist..................7 2 Important safety and product instructions..........8 2.1 Preface........................8 2.2 Product information....................8 2.3 Copyright.........................8 2.4 Manual contents..................... 8 2.5 Intended use......................8 2.5.1 Non-conventional use.................8 2.5.2 Ambient conditions for use.................9 2.6 Warning, information, and safety symbols in this manual........9 2.7 Main safety risks related to the installation, maintenance, disassembly, and...
Page 4
Framery Q Meeting Maggie 7.4 Install the upper and lower frames..............49 7.5 Install the booking system bracket (optional)............51 8 Back frames and glasses................. 59 8.1 Install the side frames (back)................59 8.2 Install the lower frame..................62 8.3 Install the back glasses..................63 8.4 Install the upper frame..................
Page 5
Framery Q Meeting Maggie 17 Finish the installation................133 18 Moving the pod (optional)..............135...
Framery Q Meeting Maggie 1 Warranty checklist For the product warranty to be valid: Fill this checklist and send it to Framery after pod installation. Take a photo or scan the filled list and send it to Framery at warranty@frameryacoustics.com. Leave the completed list inside the pod.
• Installation instructions 2.5 Intended use The Framery Q is a pod intended for short term indoor commercial and household use by one to four (1-4) people at a time. Warning: WARNING –To reduce the risk of burns, fire, electric shock, or injury to persons: Use this product only for its intended use as described in the user instructions.
Framery Q Meeting Maggie • Making alterations to the pod • Using the pod in spite of obvious defects or damage • Using the pod outdoors or in conditions where the temperature or air quality is not safe • Climbing on top of the product or placing any load on the roof of the product •...
Framery Q Meeting Maggie 2.7.1 Installation, maintenance, and disassembly WARNING! To reduce the risk of burns, fire, electric shock, or injury to persons, obey the following: Use cut resistant safety gloves during the installation, maintenance, or disassembly of the product.
Do not connect any extension cords to the power outlet(s) of the product. 2.7.3 Fire safety The fire load for the Framery Q is approx. 5200 MJ. WARNING! To reduce the risk of burns, fire, electric shock, or injury to persons,...
Maximum loads for all Framery Q tables: • 131 lb (60 kg) Maximum load for Framery Q seats: • Meeting Maggie sofa: 600 lbs (272 kg) • PAL90 and PAL110 stool: 300 lbs (136 kg) Maximum load for the display bracket is 22 lbs (10 kg).
Framery Q Meeting Maggie Do not use the product if the ventilation is not functioning. Do not use the product if the ventilation channels are blocked. Keep the ventilation channels free of lint, hair, and the like. Do not use the pod if you notice any defects in the electrical equipment or if the product is not working properly.
Framery Q Meeting Maggie 3 Installation requirements 3.1 Tools and accessories Figure 1: Tools and accessories needed for installation and maintenance Note: Use a white rubber mallet to prevent leaving marks on the body covers. Note: Use a plastic chisel to remove the body covers.
Framery Q Meeting Maggie Note: Use a separate piece of carpet in the door installation. Note: Use a lint-free cloth to clean the pod. Note: Use a mild alcohol-based cleaning solution to clean the pod. Tip: Use glass washing liquid as a lubricant to help install the seal.
Framery Q Meeting Maggie Figure 3: Installation space measurements 3.4 Operating space Make sure that the pod has enough space for the air to circulate correctly. Figure 4: Operating space measurements Installation instructions info@frameryacoustics.com...
Framery Q Meeting Maggie 4 Floor 4.1 Install the casters (optional) Lay the floor modules down on the side. If the delivery includes the optional casters, install the casters with 6.3x14 screws (4 pcs each). Lay the floor modules down on the floor.
Framery Q Meeting Maggie 4.2 Prepare the acoustic panel Remove acoustic panel out of the floor. Cut the acoustic panel at the pre-cut line. Installation instructions info@frameryacoustics.com...
Framery Q Meeting Maggie Place the smaller part of the acoustic panel against the back edge of the floor. 4.3 Connect the floor modules Lay the floor modules down at the intended final location. Leave approximately 0.5 m (1.8 ft) of empty space behind the floor modules.
Page 20
Framery Q Meeting Maggie Install guide pins (2 pcs) to the holes in one of the floor modules. Note: Make sure that the flat side of the guide pin goes into the mounting hole. Push the floor modules together. Installation instructions...
Page 21
Framery Q Meeting Maggie Install flanged M8x50 bolts (4 pcs) and M8 nuts (4 pcs). Unscrew the 4x20 screws (4 pcs) and remove the cover plates (4 pcs). Set the cover plates and screws aside. Installation instructions info@frameryacoustics.com...
Page 22
Framery Q Meeting Maggie Install guide pins (4 pcs) to the holes on the front of the floor. Note: Make sure that the flat side of the guide pin goes into the mounting hole. Install the front lower frame to the front of the floor with M8x60 bolts (2 pcs) and M8 washers (2 pcs) at the small openings and with one M8x35 bolt and M8 washer at the center opening.
Page 23
Framery Q Meeting Maggie Install guide pins (4 pcs) to the holes on the back of the floor. Note: Make sure that the flat side of the guide pin goes into the mounting hole. Install the back lower frame to the floor with M8x60 bolts (2 pcs) and M8 washers (2 pcs) at the small openings and with one M8x35 bolt and M8 washer at the center opening.
Framery Q Meeting Maggie 4.4 Level the floor Screw out the feet of the leveling screws (8 pcs) with a 4 mm hex key or 6 to 7 mm flathead screwdriver. Note: Make sure that the feet of the leveling screws are past the floor board.
Page 25
Framery Q Meeting Maggie Measure the floor module with a spirit level at six measuring points: • On top of the walls on the right-hand and left-hand sides • On the ABS strips at the edges of the floor modules Measure opposite points repeatedly and adjust the feet of the leveling screws gradually.
Framery Q Meeting Maggie 5 Install the wall modules 5.1 Remove the wall cover panels Place the wall modules lengthwise against a wall. Unscrew the 4x30 screws (24 pcs) and remove the cover panels (4 pcs). Set the cover panels and screws aside.
Framery Q Meeting Maggie 5.2 Connect the wall modules to the floor Install the guide pins (4 pcs) to the mounting holes of the floor modules. Note: Make sure that the flat side of the guide pin goes into the mounting hole.
Page 28
Framery Q Meeting Maggie Install M8x35 bolts (4 pcs) and M8 washers (4 pcs) and tighten by hand. Note: Support the wall until it is secured with the bolts. Lift the other wall module into place. Note: Make sure that the "This side up" -sticker is on the top edge of the wall.
Page 29
Framery Q Meeting Maggie Install M8x35 bolts (4 pcs) and M8 washers (4 pcs) and tighten by hand. Note: Support the wall until it is secured with the bolts. Installation instructions info@frameryacoustics.com...
Framery Q Meeting Maggie 6 Roof 6.1 Connect the roof modules Unscrew the 4x20 screws (1 pcs each) and remove the roof cover plates (1 pcs each) from both roof modules. Set the cover plates and screws aside. Install the guide pins (2 pcs) to the mounting holes in one of the roof modules.
Page 32
Framery Q Meeting Maggie Install guide pins (4 pcs) to the mounting holes at the front edge of the roof. Note: Make sure that the flat side of the guide pin goes into the mounting hole. Push the back upper frame into place.
Framery Q Meeting Maggie Install with M8x60 bolts (2 pcs) and M8 washers (2 pcs) at the small openings and with one M8x35 bolt and M8 washer at the center opening. Note: Press the acoustic panel aside to reach the bolt holes. Make sure that you return the acoustic panel to its original position.
Page 34
Framery Q Meeting Maggie Install the guide pins (4 pcs) to the mounting holes of the wall modules. Note: Make sure that the guide pins are installed to the correct holes (closer to the wall felt). Note: Make sure that the flat side of the guide pin goes into the mounting hole.
Page 35
Framery Q Meeting Maggie Lift the roof onto the wall modules. Warning: Heavy object, risk of injury! Lifting requires 2 people. Warning: Keep the installation area clear of objects that you may stumble over. Plan the lift beforehand. Obey all local safety instructions regarding lifting and work place safety.
Framery Q Meeting Maggie 7 Front frames and glasses 7.1 Install the side frames (front) Remove the front lower frame from the floor. Set the frame and bolts aside. Note: Leave the lower frame guide pins in place. Note: Press the acoustic panel aside to reach the bolt holes. Make sure that you return the acoustic panel to its original position.
Page 37
Framery Q Meeting Maggie Push the additional frame pieces (4 pcs) into place. Note: Make sure that the longer end of the additional frame piece is on the wall side. Install guide pins (8 pcs) to the holes on the front of the pod.
Page 38
Framery Q Meeting Maggie Lift the left-hand side frame into place. Note: Support the frame until securely fastened. Install the left-hand frame with M8x35 bolts (2 pcs) and M8 washers (2 pcs), Installation instructions info@frameryacoustics.com...
Page 39
Framery Q Meeting Maggie Lift the right-hand side frame into place. Note: Support the frame until securely fastened. Install the right-hand frame with M8x35 bolts (2 pcs) and M8 washers (2 pcs), Installation instructions info@frameryacoustics.com...
Framery Q Meeting Maggie 7.2 Install the control panel (optional) Insert the rubber cover to the U-profile on top of the strike plate-side glass frame. Remove the plastic sticker over the holes for the control panel cord and screws on the strike plate-side glass frame.
Page 41
Framery Q Meeting Maggie Install the control panel bracket on the strike plate-side glass frame with M4x10 screws (2 pcs). Guide the control panel cord in through the hole in the middle of the strike plate-side glass frame and out through the U-profile on top of the strike plate-side glass frame.
Page 42
Framery Q Meeting Maggie Install the rubber grommet into the hole in the control panel case. Install the magnets (2 pcs) behind the control panel with M4x10 screws (2 pcs). Use a hand tool to tighten the screws. Installation instructions...
Page 43
Framery Q Meeting Maggie Connect the control panel cord to the panel. Install the control panel into the bracket. Note: The control panel attaches to the bracket with magnets. Note: Make sure that the cord is not caught between the magnets and the case.
Framery Q Meeting Maggie 7.3 Install the front glasses Remove approximately 10 cm (4 in) of the protective film from the top and bottom of the aluminum frame of the lock-side glass. If installing the optional booking system bracket, install the rubber lead-through to the groove at the bottom of the aluminum frame.
Page 45
Framery Q Meeting Maggie If installing the optional booking system bracket, guide the customer supplied USB cord through the hole behind the strike plate and down out of the bottom of the aluminum frame. Note: Make sure that the USB A connector of the cord is at the bottom of the aluminum frame.
Page 46
Framery Q Meeting Maggie Guide the strike plate-side glass into the grooves and slide it into place. Note: Make sure that the strike plate-side glass with the strike plate is on the correct side for the door handing. Note: If installing the optional booking system bracket, make sure that the USB cord is not damaged during the installation.
Page 47
Framery Q Meeting Maggie Remove approximately 10 cm (4 in) of the protective film from the top and bottom of the aluminum frame of the hinge-side glass. Guide the hinge-side glass into the grooves and slide it into place. Tip: Push the roof up from the center joint at the front of the pod to make the installation easier.
Page 48
Framery Q Meeting Maggie Measure the straightness of the hinge-side glass frame with a spirit level. Adjust if needed and install with M8x20 screws (2 pcs) and M8 washers (2 pcs). Use a hex key. Tighten the nylon screws (2 pcs each side) on the sides of the front of the pod with a flat-head screwdriver.
Framery Q Meeting Maggie 10. Tighten M8x35 bolts (8 pcs on each side) with a spanner. 7.4 Install the upper and lower frames Install guide pins (8 pcs) to the holes on the front of the pod. Note: Make sure that the flat side of the guide pin goes into the mounting hole.
Page 50
Framery Q Meeting Maggie Install the upper frame with M8x60 bolts (2 pcs) and M8 washers (2 pcs) at the small openings and with one M8x35 bolt and M8 washer at the center opening. Note: Support the frame until securely fastened.
Framery Q Meeting Maggie 7.5 Install the booking system bracket (optional) Choose the small or large wooden back plate according to the size of the customer supplied tablet bracket. Unscrew the M5x25 Taptite screws (2 pcs) and remove the strike plate from the lock- side aluminum frame.
Page 52
Framery Q Meeting Maggie Cut the rubber grommet open vertically. Install the small rubber grommet onto the USB cord and insert the grommet into the hole in the lock-side glass. Note: Make sure that you leave enough cord on the out side to reach the customer supplied tablet.
Page 53
Framery Q Meeting Maggie Install the large rubber grommet to the strike plate of the booking system bracket. Installation instructions info@frameryacoustics.com...
Page 54
Framery Q Meeting Maggie Measure the correct place for the rubber spacer on the chosen wooden back plate and install with one 4x20 screw. Installation instructions info@frameryacoustics.com...
Page 55
Framery Q Meeting Maggie Lead the USB cord through the grommet in the strike plate. Assemble the booking system bracket with one M6x30 screw and one M6 barrel nut. Hold the nut in the slot while tightening the screw. Installation instructions...
Page 56
Framery Q Meeting Maggie Pull the excess cord out of the slot in the strike plate. Install the strike plate with bracket assembly to the lock-side aluminum frame with the M5x25 Taptite screws (2 pcs) set aside earlier. Use a hand tool.
Page 57
Framery Q Meeting Maggie 10. Feed the excess USB cord into the frame. Tip: You may need to pull on the cord at the opening near the floor to be able to adjust the length. 11. Install the plastic cover to the slot in the strike plate.
Page 58
Framery Q Meeting Maggie 12. Guide the lower end of the USB cord into the groove at the side of the floor and along the top of the insulation board to the free space in the floor. Installation instructions info@frameryacoustics.com...
Framery Q Meeting Maggie 8 Back frames and glasses 8.1 Install the side frames (back) Remove the back upper frame from the roof. Set the frame and bolts aside. Note: Leave the upper frame guide pins in place. Installation instructions...
Page 60
Framery Q Meeting Maggie Remove the back lower frame from the floor. Set the frame and bolts aside. Note: Leave the lower frame guide pins in place. Install guide pins (8 pcs) to the vacant holes on the back of the pod.
Page 61
Framery Q Meeting Maggie Lift the left-hand side frame into place. Note: Support the frame until securely fastened. Install the left-hand frame with M8x35 bolts (2 pcs) and M8 washers (2 pcs). Installation instructions info@frameryacoustics.com...
Framery Q Meeting Maggie Lift the right-hand side frame into place. Note: Support the frame until securely fastened. Install the right-hand frame with M8x35 bolts (2 pcs) and M8 washers (2 pcs). 8.2 Install the lower frame Install the lower frame to the floor with M8x60 bolts (2 pcs) and M8 washers (2 pcs) at the small openings and with one M8x35 bolt and M8 washer at the center opening.
Framery Q Meeting Maggie 8.3 Install the back glasses Lift one side glass into the groove in the lower frame and slide it into place. Note: Make sure that the glass sits at the inner edge of the groove. Installation instructions...
Page 64
Framery Q Meeting Maggie Lift the other side glass into the groove in the lower frame and slide it into place. Note: Make sure that the glass sits at the inner edge of the groove. Lift the center glass into place.
Framery Q Meeting Maggie 8.4 Install the upper frame Turn the upper frame onto the edge of the glasses and push the frame into place against the roof. Note: Make sure that the glasses stay aligned while installing the upper frame.
Page 66
Framery Q Meeting Maggie Tighten the nylon screws (2 pcs each side) on the sides of the back of the pod with a flat-head screwdriver. Do not overtighten. Note: Make sure that the back glasses stay aligned and sit snugly in the H- profile seals when tightening the nylon screws.
Framery Q Meeting Maggie 9 Install the seals Seal the back of the pod with a wedge-shaped seal between the glasses and frames. Note: Install the seal on the outside of the back of the pod and cut off any excess.
Page 68
Framery Q Meeting Maggie Install the wedge-shaped seal to the front side glasses from the inside of the pod. Note: Make sure you install the seal on the inside and cut off any excess. Tip: Use glass washing liquid as a lubricant to help install the seal.
Framery Q Meeting Maggie 10 Install the cover panels and plates Install the roof cover plates (4 pcs) with 4x20 screws (1 pcs each). Note: Place the countersunk holes upwards. Use the existing screw holes. Install the floor cover plates (4 pcs) with 4x20 screws (1 pcs each).
Page 70
Framery Q Meeting Maggie Install the wall cover panels (4 pcs) with 4x30 screws (8 pcs each). Note: Make sure that the grooves in the panels are on the outer edge of the panel. Use the existing screw holes. Note: If you install for the first time, you need two extra screws per panel, in addition to the ones removed at the beginning of the installation.
Framery Q Meeting Maggie 11 Install the electrical equipment 11.1 Install the power cord from the floor If installing the power cord from the floor, follow these instructions. If you intend to install the power cord from the roof, see Install the power cord from the roof on page 73.
Page 72
Framery Q Meeting Maggie Feed the power cord through the opening on the outside of the floor. Feed the power cord along the electrical pipe and through the opening in the center joint. Note: Make sure that only 4.5 m (15 ft) of the cord is left ourside the pod, loop the excess into the floor.
Framery Q Meeting Maggie From inside the pod, feed the DC extension cord into the electric pipe in the ceiling and down to the opening in the floor. At the opening, feed the DC extension cord into the electric pipe in the floor and through the opening in the center joint.
Page 74
Framery Q Meeting Maggie Unscrew the 4x20 screw (1 pcs) and remove the cover plate at the foot of the right side wall. Set the screw and cover plate aside. From inside the pod, feed the power cord and the DC extension cord into the electric pipe in the ceiling and down to the opening in the floor.
Framery Q Meeting Maggie At the opening, feed the power cord and DC extension cord into the electric pipe and through the opening in the center joint. 11.3 Install the LAN cord (optional) Choose which side of the floor you want to install the LAN cords to. The following instructions show installation from the right side.
Framery Q Meeting Maggie Feed the LAN cords one at a time along the electrical pipe to the center of the floor. 11.4 Install the power unit Make sure that the ON/OFF switch of the power unit is in the "I" position.
Page 77
Framery Q Meeting Maggie Place the power unit with the converter in the free space in the floor module next to the small piece of acoustic panel. Place the power unit closer to the center joint. Note: Make sure that the power unit and the converter do not block any ventilation openings.
Page 78
Framery Q Meeting Maggie Connect the DC extension cord to the DC connector of the converter. If installing the optional booking system bracket or the optional wireless charger, connect the 5V unit cord between the DC extension cord and the DC connector of the converter.
Framery Q Meeting Maggie If installing the optional booking system bracket, connect the customer supplied USB cord to the USB connector of the 5V unit. 11.5 Install the floor cover board Place the floor cover board into the opening in the floor.
Framery Q Meeting Maggie Install the floor cover board with 5x50 screws (5 pcs). Note: Make sure that the electrical cords are not damaged or pinched. 11.6 Install the control unit Insert the control unit bracket into the back of the control unit.
Page 81
Framery Q Meeting Maggie Turn the bracket into place. Install the bracket with the control unit into the opening in the ceiling with 4x30 screws (2 pcs). Note: Make sure that you install the control unit to the right-hand side of the center beam.
Page 82
Framery Q Meeting Maggie Connect the DC extension cord to the PWR IN connector. Connect the nearest fan power cord to the FAN 1 connector. Installation instructions info@frameryacoustics.com...
Framery Q Meeting Maggie Lead the second fan power cord through the groove in the center beam and connect it to the FAN 2 connector. 11.7 Install the motion detector and light Remove the bracket from the motion detector. Installation instructions...
Page 84
Framery Q Meeting Maggie Install the motion detector bracket to the ceiling at the back of the pod with 4x20 screws (3 pcs). Note: Make sure that you align the bracket with the opening as shown. The distance between the edge of the bracket and the glass is 125 mm (4 15/16 in).
Page 85
Framery Q Meeting Maggie Connect motion detector cord to the PIR connector of the control unit. Lift the motion detector to the bracket and slide the motion detector into place. Installation instructions info@frameryacoustics.com...
Page 86
Framery Q Meeting Maggie Connect the light cord to the LED 1 connector of the control unit. Install the wire end of the light under the flap of the motion detector bracket and turn the light against the ceiling. The light attaches to the ceiling with magnets. Align the light to the center of the ceiling.
Framery Q Meeting Maggie 12 Install the interior 12.1 Assemble the table Remove the rubber cover strip from the table leg. Remove the 4x20 screws and the small floor cover board. Installation instructions info@frameryacoustics.com...
Page 88
Framery Q Meeting Maggie If not installing the optional LAN data cartridge continue to step 5. Pull the two LAN cords out of the hole in the floor. Lead the LAN cords from the floor through the base of the table leg.
Page 89
Framery Q Meeting Maggie Set the base of the table leg into place. Note: Make sure that the notch at the base of the table leg is on the same side as the notch in the floor. If installing a wide table, install the table installation brackets with 5x25 screws (1 pcs each) under the table top.
Framery Q Meeting Maggie 12.2 Install the table Install the base of the table leg with M6x20 countersunk screws (6 pcs) and 5x50 screws (4 pcs). Note: Make sure that the cords are not pinched or damaged during the installation.
Page 91
Framery Q Meeting Maggie If installing the turnable table, install the table top to the table leg with M5x10 cylinder head screws (4 pcs). Use the threads in the table top as reference. If the turnable table top feels too stiff or too loose, adjust the M6x20 screw.
Framery Q Meeting Maggie If installing a wide table, install the installation brackets under the table top to the walls with 5x50 screws (1 pcs each). Note: Make sure that the distance from the glass to the back edge of the table top is equal over the entire width of the table.
Page 93
Framery Q Meeting Maggie Guide the ends of the LAN cords one at a time through the free opening at the side of the LAN data cartridge. Connect the LAN cords to the connectors of the LAN data cartridge. Installation instructions...
Framery Q Meeting Maggie Place the LAN data cartridge onto the power outlet and turn it counter-clockwise until it locks into place. Continue as instructed in the following section with the LAN data cartridge in place. Note: Make sure that the LAN cords and the power outlet cord are on the same side after attaching the LAN data cartridge to the power outlet.
Page 95
Framery Q Meeting Maggie Turn the power outlet counter-clockwise until it locks into place. Lead the power outlet cord through the opening at the base of the table leg. Installation instructions info@frameryacoustics.com...
Page 96
Framery Q Meeting Maggie Connect the power outlet cord to the power unit. A "click" sound is audible when the connector locks into place. Feed the power outlet cord into the groove in the table leg. If the table is equipped with a wireless charger, also pull the excess cord of the wireless charger into the groove in the table leg.
Page 97
Framery Q Meeting Maggie If the optional wireless charger is installed, lead the USB cord from the wireless charger through the opening at the base of the table leg. If the optional wireless charger is installed, connect the USB cord to the USB connector of the 5 V unit.
Page 98
Framery Q Meeting Maggie Install the small cover board with 4x20 screws (2 pcs). Note: Make sure that the cords are not pinched or damaged Press the rubber strip onto the table leg. Installation instructions info@frameryacoustics.com...
Framery Q Meeting Maggie 12.5 Install the carpet and the floor grid Install the carpet into place so that the edge slot is on the door side and the floor grid opening is on the glass wall side. Note: Press the edges under the wall felt.
Framery Q Meeting Maggie 13 Install the door 13.1 Install the floor threshold Set the threshold down at the doorway. Installation instructions info@frameryacoustics.com...
Page 101
Framery Q Meeting Maggie Slide the threshold against the door frame. Note: Make sure that the side seals are not between the threshold and the door frame. Neatly cut the side frame seal to the correct length, if needed. Note: Make sure that the side frame seals and the threshold seal do not overlap.
Framery Q Meeting Maggie 13.2 Install the control panel cord and the ceiling threshold If not installing the optional control panel, continue to step 4. Punch out the precut hole in the ceiling felt. Guide the control panel cord from the U-profile on the strike plate-side glass frame to the control unit and pull it out of the front opening in the ceiling.
Page 103
Framery Q Meeting Maggie Connect the control panel cord to the UI connector of the control unit. Lift the ceiling threshold up to the top of the doorway. Note: Slant the threshold and lift the right edge up first. Make sure that you do not scratch the door frames with the threshold.
Page 104
Framery Q Meeting Maggie Slide the threshold outwards against the door frame. Note: Make sure that the side frame seals are not between the threshold and the door frame. Neatly cut the side frame seal to the correct length, if needed.
Framery Q Meeting Maggie 13.3 Install the door Detach the halves of the hinges from each other. Note: Do not peel off the black tape from the hinges. The tape is needed to protect the glass parts from the metal hinges.
Page 106
Framery Q Meeting Maggie Install the 1 mm adjustment plate into the lower hinge mounting hole and attach half of both hinges with M6x30 Taptite screws (4 pcs each). Use a hand tool. Note: Do not use power tools to install the hinges.
Framery Q Meeting Maggie Install the remaining halves of the hinges to the door with M6x30 Taptite screws (4 pcs each). Use a hand tool. Note: Do not use power tools to install the hinges. Note: Peel back enough of the protective plastic to install the hinges. Do not remove the protective plastic completely.
Page 108
Framery Q Meeting Maggie Remove the protective plastic on the inside of the door. Push the handle with the spindle attached to it into place on the outside of the door. Pierce the plastic in the lock case with the spindle.
Page 109
Framery Q Meeting Maggie Install an M5x46 screw in the hole at the center of the handle from the inside of the door. Note: Check that the cover plate is positioned straight. Install M5x46 screws (2 pcs) in the vacant holes from the inside of the door.
Framery Q Meeting Maggie Tighten the set screw on the inside handle. The resistance increases steadily until the screw pierces the spindle. You can feel the resistance stop when the set screw pierces the spindle. Note: In the final position, the head of the set screw is slightly above the handle surface.
Page 111
Framery Q Meeting Maggie Shorten the M5 screws to the correct length. Warning: Wear safety glasses when cutting the screws. Shorten the twist spindle to the correct length at the first groove in the twist spindle. Warning: Wear safety glasses when cutting the twist spindle.
Page 112
Framery Q Meeting Maggie Assemble the connector plate, twist spindle, and the previously cut M5x40 screws (2 pcs). Assemble the smart lock cylinder and the cylinder escutcheon. Note: Make sure that you install the cylinder escutcheon the right side up.
Page 113
Framery Q Meeting Maggie Shorten the twist spindle to the correct length at the third groove in the twist spindle. Warning: Wear safety glasses when cutting the twist spindle. Push the twist spindle through the extension plates to the smart lock.
Page 114
Framery Q Meeting Maggie Place the connector plate assembly onto the upper opening in the door. Install the smart lock assembly and the door handle with the spindle onto the door from outside, and tighten the screws (2 pcs) from inside.
Page 115
Framery Q Meeting Maggie 10. Push the counter part of the door handle onto the door from inside. 11. Tighten the M5x32 screw above the door handle from inside. Note: Check the straightness of the cover plate before fully tightening the screw.
Page 116
Framery Q Meeting Maggie 12. Install the thumb turn with the previously cut M5x61 screws (2 pcs), and the handle plate with the remaining M5x32 screw from inside. Note: Check the straightness of the cover plate outside the door before fully tightening the thumb turn screws.
Framery Q Meeting Maggie 14. Check the gap between the lock and the strike plate. If the gap is larger than 4 mm, see Adjust the strike plate. 13.5.1 Adjust the strike plate The gap between the lock and strike plate can be adjusted with the adjustment plates included in the delivery.
Framery Q Meeting Maggie Re-install the strike plate and the adjustment plates. 13.5.2 Check the lock function With the door open, press the thumb turn down and push the sliding snib up. Installation instructions info@frameryacoustics.com...
Page 119
Framery Q Meeting Maggie Press the door handle down to check the lock latch function. If the lock latch does not return easily to the starting position, see for instructions. Press the smaller latch in with your thumb and try pressing the door handle down.
Page 120
Framery Q Meeting Maggie With the smaller latch pressed in, press the thumb turn down to test the lock latch function. The lock latch should retract inside the lock case. Go into the pod and close the door. Press the door handle down.
Page 121
Framery Q Meeting Maggie Press the door handle and the thumb turn down. The door should open. Program the smart lock as instructed by the manufacturer. Note: Once the smart lock system is in use, the door cannot be opened by pressing the door handle down.
Framery Q Meeting Maggie 14 Install the coat hooks Measure the places for the coat hooks at both walls. 170 cm (67 in) up from the base of the wall and 9 cm (3 ½ in) from the front glass wall.
Framery Q Meeting Maggie 15 Assemble the seats Install the seat legs to the bottom of the seat with 4.25x25 wronic screws (4 pcs each). Lift the seat into place. If installing the optional straight backrest, lift the seat into place and lay the backrest on the back edge of the seat.
Framery Q Meeting Maggie 16 Install the body covers 16.1 Install the roof cover panel Install the roof cover panel with 4x30 screws (6 pcs). Note: If you installed the power cord to the roof, guide it through the roof cover panel hole and into the groove before setting the roof cover panel into place.
Framery Q Meeting Maggie 16.2 Install the bottom body covers If you installed the power cord to the floor, add the rubber lead-through to one bottom body cover and use this body cover on the side of the power cord.
Page 126
Framery Q Meeting Maggie Slide the left-hand bottom body cover under the pod. Guide the edge of the cover into the groove under the floor. Note: If you installed the power cord to the floor, make sure that you install the bottom body cover with the rubber lead-through on the side of the power cord.
Page 127
Framery Q Meeting Maggie Slide the right-hand bottom body cover under the pod. Guide the edge of the cover into the groove under the floor. Note: If you installed the power cord to the floor, make sure that you install the bottom body cover with the rubber lead-through on the side of the power cord.
Framery Q Meeting Maggie 16.3 Install the roof body covers If you have installed the power cord from the ceiling, cut the notch out of the body cover. This is not necessary if you have installed the power cord to the floor module.
Page 129
Framery Q Meeting Maggie Guide the other edge of the body cover into the groove at the upper part of the wall. Repeat steps 2 and 3 to install the other curved roof body cover to the other side of the roof.
Page 130
Framery Q Meeting Maggie Guide the other edge of the body cover into the groove at the edge of the roof. Guide the edge of the straight roof body cover on the right-hand side into the groove at the center of the roof.
Framery Q Meeting Maggie Guide the other edge of the body cover into the groove at the edge of the roof. 16.4 Install the wall body covers Guide the edge of one wall body cover into the groove at the top of the wall.
Page 132
Framery Q Meeting Maggie Press the body cover into the upper groove with one hand and bend the body cover lightly outward with your other hand. Slide the lower edge of the body cover into the groove at the bottom of the wall and press the body cover into place.
Page 133
Framery Q Meeting Maggie 17 Finish the installation Clean the glasses with glass washing liquid and a lint-free cloth. Connect the main power cord to a power outlet. Installation instructions info@frameryacoustics.com...
Page 134
Framery Q Meeting Maggie Fill out the warranty checklist and send it to Framery. Note: The warranty is only valid with the filled-out warranty checklist. Installation instructions info@frameryacoustics.com...
Page 135
Framery Q Meeting Maggie 18 Moving the pod (optional) Lift the seats out of the pod and remove the floor threshold, the floor grid, and the carpet. Warning: Risk of injury. Do not go into the pod when it is standing on the casters.
Page 136
Framery Q Meeting Maggie Carefully push the pod to the new location. Note: Only push the pod below the vertical middle, do not tow it. Note: Only move the pod at walking speed. Note: Only move the pod on even surfaces. The pod can cross thresholds a maximum of 3 mm.
Page 137
Framery Q Meeting Maggie Screw out the feet of the leveling screws (8 pcs) gradually with a 6 to 7 mm a flathead screwdriver. Make sure that the feet of the leveling screws are slightly past the casters and touch the floor.
Page 138
Framery Q Meeting Maggie Install the threshold, the floor grid, and the carpet. Lift the seats into the pod. Installation instructions info@frameryacoustics.com...
Need help?
Do you have a question about the Maggie and is the answer not in the manual?
Questions and answers