Page 1
FULL MANUAL HW-Q990B Imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/register...
Page 2
Refer to the table below for an explanation of symbols which may be • This apparatus shall always be connected to a AC outlet with a on your Samsung product. protective grounding connection. • To disconnect the apparatus from the mains, the plug must be...
Page 3
PRECAUTIONS 1. Ensure that the AC power supply in your house complies with the power requirements listed on the identification sticker located on the bottom of your product. Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation (7~10 cm).
• For more information about the power supply and power consumption, refer to the label attached to the product. (Label: Rear of the Soundbar Main Unit) • To purchase additional components or optional cables, contact a Samsung Service Centre or Samsung Customer Care. • For more information about the wallmount or rubber-foot, see pages 30~32.
02 PRODUCT OVERVIEW Top Panel of the Soundbar (Multi Function) Button • In standby mode, press the (Multi Function) button to turn on the Soundbar. • Press the (Multi Function) button to change the input source. (Volume) Button Adjusts the volume. (Mic On/Off) Button Press the button to turn the microphone on or off.
03 USING THE SOUNDBAR REMOTE CONTROL Inserting Batteries before using the Remote Control (AAA batteries X 2) Slide the back cover in the direction of the arrow until it is completely removed. Insert 2 AAA batteries (1.5V) oriented so that their polarity is correct. Slide the battery cover back into position. •...
Page 9
By pressing the button, you can set the audio function such as Auto EQ, Spacefit sound, AVA, Voice enhance mode, Night mode, Sync, Surround speaker mode, Virtual. The desired item can be adjusted using the Up/Down Sound Control buttons. • You can use the Auto EQ function if a subwoofer is connected. •...
Active Voice Amplifier (AVA) • Analyzes external noise in real time while soundbar is playing, so that voice audio can always be heard clearly. • No data is saved during the analysis. Using the Hidden Buttons (Buttons with more than one function) Hidden Button Reference page Remote Control Button...
• Set the TV speaker to External Speaker to use this function. • Manufacturers supporting this function: Samsung, VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA 1. Turn Off the Soundbar. 2. Push up and hold the WOOFER button for 5 seconds.
04 CONNECTING THE SOUNDBAR Connecting the power and units Use the Power cord to connect the Subwoofer, Surround Speakers, and Soundbar to an electrical outlet in the following order: • For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label: Rear of the Soundbar Main Unit) 1.
Recommended Speaker Layout CAUTION • Wireless receiving antennas are built into the wireless subwoofer and surround speakers. Keep the units away from water and moisture. Soundbar • For optimal listening performance, make sure that the areas around the Subwoofer 0° wireless subwoofer and surround speakers locations are clear of any obstructions.
Manually connecting the Subwoofer or Surround Speakers Before performing the manual connection procedure below: • Check whether the power cables for the Soundbar and subwoofer or Surround Speakers are connected properly. • Make sure that the Soundbar is turned off. 1.
Surround Speakers Connect again. See the instructions for manual Connection failed connection on page 14. Subwoofer Red and blue See the contact information for the Samsung Service Blinking Malfunction Centre in this manual. Surround Speakers Red and blue NOTE •...
Auto EQ Samsung’s Auto EQ Technology uses a microphone mounted in the subwoofer to detect and correct low-frequency response peaks caused by the room dimensions and the subwoofer location. The result will be a more neutral overall low-frequency response. • Subwoofer should be placed with a minimum of 3” (8 cm) clearance from each side to the nearest boundary.
• When connecting a TV that supports the eARC function, “eARC” appears on the display and the sound is heard. • To connect with eARC, the eARC function in the TV menu should be set to On. Refer to the TV user manual for details on setting. (e.g. Samsung TV : Home ( ) → Menu → Settings ( ) →...
Connecting using an Optical Cable Pre-connection Checklist • When both the HDMI cable and optical cable are connected, the HDMI signal is received first. • When you use an optical cable and the terminals have covers, be sure to remove the covers. Bottom of the Soundbar Optical Cable (not supplied) DIGITAL AUDIO IN...
3. Select “Soundbar Q***B” from the list on TV’s screen. An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV’s Bluetooth device list. To connect the Samsung TV to the Soundbar, select the message, and then establish a connection.
) → Menu → Settings ( ) → All Settings ( ) → Sound → Sound Output → Soundbar Q***B (Wi-Fi) NOTE The Wi-Fi Dolby Atmos connection is available in some Samsung TVs and some Soundbar models. ENG - 20...
Using the Q-Symphony Function For Q-Symphony, the Soundbar syncs with a Samsung TV to output sound through two devices for optimum surround effect. When the Soundbar is connected, the menu, “TV+Soundbar” appears under the Sound Output menu of the TV. Select the corresponding menu.
( Up ) → “Spacefit sound On”) • This is available in all Sound modes. Method 2. Connecting via TV To enable this function, turn on the Adaptive Sound+ mode on your Samsung TV menu. (Home ( ) → Menu → Settings ( ) →...
Open the audio output options on the settings menu of your BD player or other device and make sure that “No Encoding” is selected for Bitstream. For example, on a Samsung BD Player, go to Home Menu → Sound → Digital Output and then select Bitstream (unprocessed).
Method 2. Connecting using an Optical Cable Top of the Soundbar BD / DVD player / Set- top box / Game console D.IN DIGITAL AUDIO IN (OPTICAL) Optical Cable OPTICAL OUT (not supplied) Bottom of the Soundbar 1. Use an optical cable (not supplied) to connect the DIGITAL AUDIO IN (OPTICAL) on the Soundbar main and the OPTICAL OUT port on the external device.
What is the difference between BT READY and BT PAIRING? • BT READY : In this mode, you can reconnect any Samsung TV or mobile device that was connected before. • BT PAIRING : In this mode, you can connect a new device to the Soundbar.
Page 26
• A Bluetooth device may experience noise or malfunction under in the following conditions: ‒ When the body is in contact with the signal transceiver on the Bluetooth device or Soundbar ‒ In corners or when there is an obstacle in proximity, such as a wall or partition, where electrical changes may occur. ‒...
Method 2. Connecting via Wi-Fi (Wireless Network) To connect a Soundbar to a mobile device via a wireless network (Wi-Fi), the SmartThings app is required. The initial connection 1. Install and launch the SmartThings app from your mobile device (smartphone or tablet). 2.
Tap the Soundbar with your mobile device to play the sound of content on the mobile device through the Soundbar. • This function may not be supported, depending on the mobile device. • This function is only compatible with Samsung mobile devices with Android 8.1 or later. SmartThings App...
• This Samsung Soundbar supports AirPlay 2 and requires iOS 11.4 or later. With AirPlay 2, you can stream music, podcasts, and other audio from your Apple devices to the Samsung Soundbar. • Make sure the Soundbar is powered on and connected to the same Wi-Fi network as your Apple device.
09 INSTALLING THE WALL 2. Align the Wall Mount Guide’s Centre Line with the centre of your TV (if you are mounting the Soundbar below your TV), and then fix MOUNT the Wall Mount Guide to the wall using tape. •...
Wall Mount Brackets and the speakers on the wall. • Samsung Electronics is not liable for any damage to the product due to the product being installed inappropriately. • Take care not to install the speakers sideways or upside down.
Page 32
USB drive that contains the update firmware to the SERVICE port of the Soundbar. 1. Go to the Samsung website (www.samsung.com) → search for the model name from the customer support menu option. • For more information about update, refer to Upgrade Guide.
Page 33
• When any external device (STB, Bluetooth device, mobile device, etc.) is connected, adjust the volume of the external device. • For sound output of the TV, select Soundbar. (Samsung TV: Home ( ) → Menu → Settings ( ) →...
Page 34
• Your device is unable to play the input signal. Change the mode. Then no sound is output from the TV. TV’s audio output to PCM or Dolby Digital. (For a Samsung TV: Home ( ) → Menu → Settings ( ) →...
Page 35
13 LICENCE 14 OPEN SOURCE LICENCE NOTICE To send inquiries and requests for questions regarding open sources, contact Samsung Open Source (http://opensource.samsung.com) Dolby, Dolby Atmos, and the double-D symbol are registered 15 IMPORTANT NOTES trademarks of Dolby Laboratories Licensing Corporation.
Page 36
AMPLIFIER Rated Output power 210 W NOTE • Samsung Electronics Co., Ltd reserves the right to change the specifications without notice. • Weight and dimensions are approximate. • For India Only “This product is RoHS compliant” • For Taiwan Only...
Page 37
Tham khảo bảng dưới đây để xem phần giải thích cho các biểu tượng có thể • Để ngắt thiết bị ra khỏi nguồn, phải rút phích cắm ra khỏi ổ cắm chính, xuất hiện trên sản phẩm Samsung của bạn. thì phích cắm chính mới có thể sẵn sàng hoạt động.
Page 38
THẬN TRỌNG 1. Đảm bảo nguồn cấp điện AC trong nhà bạn tuân theo các yêu cầu về nguồn điện được nêu trên nhãn nhận biết nằm ở phía dưới cùng của sản phẩm. Lắp đặt sản phẩm theo chiều ngang, trên điểm tựa thích hợp (đồ đạc trong nhà) và...
Page 39
NỘI DUNG Kiểm tra thành phần Tổng quan về sản phẩm Bảng mặt trên của Soundbar ......................7 Mặt dưới Soundbar.
Page 40
Lắp đặt Soundbar trước TV Chi tiết..........................31 Cập nhật phần mềm Tự...
Soundbar) • Để mua thêm bộ phận hay cáp tùy chọn, hãy liên hệ với Trung tâm Dịch vụ Samsung hoặc Bộ phận Chăm sóc Khách hàng của Samsung. • Để biết thêm thông tin về giá treo tường hoặc chân đế cao su, hãy xem trang 30~32.
02 TỔNG QUAN VỀ SẢN PHẨM Bảng mặt trên của Soundbar Nút (Đa chức năng) • Ở chế độ chờ, nhấn nút (Đa chức năng) để bật Soundbar. • Nhấn nút (Đa chức năng) để thay đổi nguồn đầu vào. Nút (Âm lượng) Điều chỉnh âm lượng.
03 SỬ DỤNG ĐIỀU KHIỂN TỪ XA SOUNDBAR Lắp Pin trước khi dùng Điều khiển từ xa (pin AAA X 2) Trượt nắp sau theo hướng mũi tên cho đến khi tháo nắp ra hoàn toàn. Lắp 2 pin AAA (1,5 V) theo đúng hướng của các cực.
Page 44
Bạn có thể nhấn nút này để đặt chức năng âm thanh, chẳng hạn như Auto EQ, Spacefit sound, AVA, Voice enhance mode, Night mode, Sync, Surround speaker mode, Virtual. Bạn có thể điều chỉnh mục mong muốn bằng nút Lên/Xuống. Điều khiển âm •...
Bộ khuếch đại giọng nói chủ động (AVA) • Phân tích tiếng ồn bên ngoài trong thời gian thực khi Soundbar đang phát để luôn nghe rõ giọng nói. • Không lưu dữ liệu nào trong khi phân tích. Sử dụng các Nút Ẩn (Các nút có nhiều chức năng) Nút Ẩn Trang tham khảo Nút trên Điều khiển Từ...
2. Đẩy lên và giữ nút WOOFER trong 5 giây. Mỗi khi bạn đẩy lên và giữ nút WOOFER trong 5 giây, chế độ sẽ thay đổi theo thứ tự sau: “OFF-TV REMOTE” (Chế độ mặc định), “SAMSUNG-TV REMOTE”, “ALL-TV REMOTE”.
04 KẾT NỐI SOUNDBAR Kết nối nguồn và thiết bị Sử dụng Dây nguồn để kết nối Loa siêu trầm, Loa vòm và Soundbar với ổ cắm điện theo tứ tự sau: • Để biết thêm thông tin về nguồn điện cũng như mức tiêu thụ điện năng yêu cầu, hãy tham khảo nhãn đính kèm sản phẩm. (Nhãn: Mặt sau của Thiết bị chính Soundbar) 1.
Đề xuất bố trí loa CẨN THẬN • Ăng-ten thu không dây được tích hợp vào loa siêu trầm không dây và loa vòm. Để những thiết bị này tránh xa nước và hơi ẩm. Soundbar • Để đạt hiệu suất nghe tối ưu, đảm bảo các khu vực xung quanh vị trí đặt loa siêu Loa siêu trầm 0°...
Kết nối thủ công Loa siêu trầm hoặc Loa vòm Trước khi thực hiện quy trình kết nối thủ công bên dưới: • Kiểm tra xem cáp nguồn cho Soundbar và loa siêu trầm hoặc Loa vòm có được kết nối đúng không. •...
Kết nối lại. Xem hướng dẫn kết nối thủ công trên trang 14. Màu đỏ Loa siêu trầm Màu đỏ và màu lam Xem thông tin liên hệ của Trung tâm dịch vụ Samsung trong Nhấp nháy Lỗi sách hướng dẫn này.
Auto EQ Công nghệ Auto EQ của Samsung sử dụng micro gắn ở loa siêu trầm để dò và điều chỉnh đỉnh đáp ứng tần số thấp do kích thước phòng và vị trí loa siêu trầm gây ra. Kết quả sẽ là đáp ứng tần số thấp tổng thể ở mức trung tính hơn.
• Để kết nối với eARC, cần đặt chức năng eARC ở menu TV là Bật. Tham khảo sách hướng dẫn sử dụng TV để biết chi tiết về cài đặt. (ví dụ: TV Samsung: Trang chủ ( ) → Menu → Cài đặt ( ) →...
Kết nối bằng Cáp quang Danh sách kiểm tra trước khi kết nối • Khi kết nối cả cáp HDMI và cáp quang, thiết bị sẽ nhận được tín hiệu HDMI trước. • Khi bạn sử dụng cáp quang và thiết bị đầu cuối có nắp, hãy nhớ tháo nắp ra. Mặt dưới của Soundbar Cáp quang (không đi kèm) DIGITAL AUDIO IN...
Sự khác nhau giữa BT READY và BT PAIRING là gì? • BT READY : Ở chế độ này, bạn có thể kết nối lại bất kỳ TV Samsung hay thiết bị di động nào đã được kết nối trước đó.
) → Tất cả cài đặt ( ) → Âm thanh → Đầu ra â.thanh → Soundbar Q***B (Wi-Fi) LƯU Ý Kết nối Wi-Fi Dolby Atmos có sẵn trên một số TV Samsung và một số model Soundbar. VIE - 20...
Sử dụng chức năng Q-Symphony Với Q-Symphony, Soundbar sẽ đồng bộ hóa với TV Samsung để phát âm thanh ra hai thiết bị cho hiệu ứng vòm tối ưu. Khi kết nối Soundbar, menu, “TV+Soundbar” sẽ xuất hiện bên dưới menu Đầu ra â.thanh của TV. Chọn menu tương ứng.
• Tính năng này có sẵn ở mọi chế độ âm thanh. Phương pháp 2. Kết nối qua TV Để bật chức năng này, hãy bật chế độ Adaptive Sound+ trên menu TV Samsung. (Trang chủ ( ) → Menu → Cài đặt ( ) →...
Mở tùy chọn đầu ra âm thanh trên menu cài đặt của trình phát BD hoặc thiết bị khác và đảm bảo chọn “Không mã hóa” cho Bitstream. Ví dụ: trên Trình phát BD của Samsung, truy cập vào Menu Chính → Âm thanh → Đầu ra kỹ thuật số rồi chọn Bitstream (chưa được xử lý).
Phương pháp 2. Kết nối bằng Cáp quang Mặt trên của Soundbar BD / Đầu DVD / Hộp thu phát kỹ thuật số / Máy chơi game D.IN DIGITAL AUDIO IN (OPTICAL) Cáp quang OPTICAL OUT (không đi kèm) Mặt dưới của Soundbar 1.
Sự khác nhau giữa BT READY và BT PAIRING là gì? • BT READY : Ở chế độ này, bạn có thể kết nối lại bất kỳ TV Samsung hay thiết bị di động nào đã được kết nối trước đó.
Page 61
• Thiết bị Bluetooth có thể gặp nhiễu hoặc trục trặc trong các điều kiện sau: ‒ Khi cơ thể chạm vào bộ thu tín hiệu trên thiết bị Bluetooth hoặc Soundbar ‒ Ở các góc hoặc khi có chướng ngại vật ở gần như tường hoặc vách ngăn là những nơi có thể có sự thay đổi về điện. ‒...
Phương pháp 2. Kết nối qua Wi-Fi (Mạng không dây) Để kết nối Soundbar với thiết bị di động qua mạng không dây (Wi-Fi), bạn cần có ứng dụng SmartThings. Kết nối ban đầu 1. Cài đặt và khởi chạy ứng dụng SmartThings trên thiết bị di động (điện thoại thông minh hoặc máy tính bảng) của bạn. 2.
• Chức năng này có thể không được hỗ trợ, tùy thuộc vào thiết bị di động. • Chức năng này chỉ tương thích với các thiết bị di động Samsung chạy hệ điều hành Android 8.1 trở lên. Ứng dụng SmartThings Mặt trên của Soundbar...
• Soundbar Samsung hỗ trợ AirPlay 2 và cần có iOS 11.4 hoặc phiên bản mới hơn. Với AirPlay 2, bạn có thể phát nhạc, podcast và nội dung âm thanh khác từ thiết bị của Apple tới Samsung Soundbar.
09 LẮP GIÁ TREO TƯỜNG 2. Căn chỉnh Trục tâm của thanh dẫn giá treo tường ở chính giữa TV (nếu bạn lắp Soundbar ở dưới TV), sau đó cố định Thanh dẫn giá treo tường vào tường bằng băng dính. Lưu ý...
Nếu độ bền không đáp ứng, hãy nhớ gia cố tường trước khi lắp đặt Giá đỡ trên tường và loa trên tường. • Samsung Electronics không chịu trách nhiệm về bất kỳ hỏng hóc nào đối với sản phẩm do lắp đặt sản phẩm không thích hợp.
Page 67
• Hình minh họa ở trên có thể khác nhau tùy theo model. NETWORK Samsung có thể cung cấp bản cập nhật cho vi chương trình hệ thống của Soundbar trong tương lai. Khi có bản cập nhật, bạn có thể cập nhật Soundbar bằng cách kết nối ổ đĩa USB chứa vi chương trình cập nhật với cổng SERVICE của Soundbar.
Page 68
• Khi kết nối bất kỳ thiết bị bên ngoài nào (STB, thiết bị Bluetooth, thiết bị di động, v.v.), hãy điều chỉnh âm lượng của thiết bị bên ngoài. • Với đầu ra âm thanh của TV, chọn Soundbar. (TV Samsung: Trang chủ ( ) →...
Page 69
• Thiết bị của bạn không thể phát tín hiệu đầu vào. Thay đổi đầu ra âm • Không thao tác Soundbar trong quá trình chỉnh. thanh của TV thành PCM hoặc Dolby Digital. (Đối với TV Samsung: Sau khi kết nối TV với Soundbar, tôi đã tắt chế độ Soundbar. TV không Trang chủ...
Page 70
NGUỒN MỞ Để gửi truy vấn và yêu cầu đối với các câu hỏi liên quan đến nguồn mở, hãy liên hệ với Samsung Open Source (http://opensource.samsung.com) Dolby, Dolby Atmos, and the double-D symbol are registered 15 LƯU Ý QUAN TRỌNG VỀ...
Page 71
210 W LƯU Ý • Samsung Electronics Co., Ltd có quyền thay đổi các thông số kỹ thuật mà không có thông báo. • Trọng lượng và các kích thước đều ở mức xấp xỉ. Thận trọng: Soundbar sẽ tự động khởi động lại nếu bạn bật/tắt Wi-Fi.
Page 72
** Sản phẩm được bảo hành trong các trường hợp sau: 5. Các sản phẩm do SAMSUNG sản xuất và phân phối chính thức tại thị 1. Sản phẩm còn trong thời hạn Bảo hành dựa vào tin nhắn từ tổng đài trường Việt Nam sẽ...
Page 107
低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 前述合法通信,指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 應避免影響附近雷達系統之操作。 • For Taiwan Only HW-Q990B : AC 100-240 V ~ 50/60 Hz, 41 W PS-WB99B : AC 100-240 V ~ 50/60 Hz, 32 W PS-RB99B : AC 100-240 V ~ 50/60 Hz, 19 W 注意事項:若您開啟/關閉 Wi-Fi,有源音箱將會自動重新啟動。 Wi-Fi 按住有源音箱遙控器上的...