Page 2
Magigoo Coater, 3D Printer or its peripherals. To make the most out of the Magigoo Coater, study the manual carefully and make sure that anyone using Magigoo Coater understands instructions laid out in this user manual.
Recommendations for use 3.2.1 Before Coating 3.2.2 Coating 3.2.3 After Coating 3.2.4 Cleaning the manifold 3.2.5 Cleaning Build Plate from Magigoo Adhesive compatibility Maintenance Warranty General Exclusions Conditions & Limitations Lodging Claims Applicable law and competent court Table of Contents...
Magigoo or Magigoo Pro bed adhesive to increase the reliability of 3D print, reduce 1.4 Health and Safety warping and provide easy release. Best Do not point The Coater at a person and/ results are achieved on glass build plates. or animal. 1.3 General Safety The Coater components may have sharp edges –...
Contents of the Starter Kit Parts Magigoo Original Adhesive x1 Bottle – empty bottle for water x1 Cleaning cloth Spray Head x1 Pump Head x1 Thin Film Applicator x1 Manifold Cover x1 Valves x20 Manifold Frame Bolts (M4) x2 for Thin Film Applicator...
The Case dimensions 30,5*35*11,5 cm Approximately The Coater 240mm wide thin film applicator 15cm high Bottle 250ml Compatible with Suitable to use with: Magigoo Original Magigoo Pro PP Magigoo Pro PA Magigoo Pro PC Warranty 12 months Magigoo Coater User Manual...
Straw for Spray Head (long) Cleaning Cloth Scraper Handle for Scraper Plastic Blades for Manifold assembly, size M3 Square Nuts Bolts for Manifold assembly, size M3 Bolts for Thin Film Applicator, size M4 Allen/Hex Keys for tightening bolts Magigoo Coater User Manual...
3.1.2 Assembling the manifold Read through all the steps before following step-by-step instructions. Assemble the manifold by attaching the valves and installing the thin film applicator. Take the manifold. Place one valve over each of the 13 nozzles present on the manifold frame. Insert 6 square nuts (size M3) into manifold cover.
Page 12
Do not over tighten to prevent rupture of the manifold structure. The thin film applicator is static bar and does not roll. Attempting to make the thin film applicator bar roll may cause irreversible damage. Magigoo Coater User Manual...
Page 13
Screw on the assembled manifold until it is slightly tightened and the manifold is perpendicular to the trigger. Do not over tighten to prevent rupture of the manifold. Attach the short straw to the pump. Screw on the assembled system to the Magigoo bottle. Instructions for Use...
Find a surface that can be easily cleaned. For the first time use, the Coater system needs to be primed by pumping several times until the glue starts coming out of the valves consistently. You should see 13 glue dots form on the surface.
Page 15
3.2.2 Coating Magigoo Coater is designed and built for use in FDM/FFF 3D printing to cover the build plate of a 3D print with a thin layer of Magigoo and Magigoo Pro bed adhesive to increase the reliability of 3D print, reduce warping and provide easy release. Best results are achieved on glass build plates.
Manifold needs to be cleaned thoroughly whenever a glue type is changed, to remove residue of previous glue. If the Magigoo Coater was not is use over longer period of time, manifold would need to be cleaned for better performance.
Pump at least 15 times or until the water coming out looks clean. Water may spray in different directions. If the Coater will not be in use for longer period of time, clean the thin film applicator, valves and the manifold properly, dismantle and store away in its case.
The Magigoo Coater should be used only with adhesives produced by Thought3D under the brand Magigoo or other Thought3D approved adhesives. Magigoo Coater has been designed to work with Magigoo and Magigoo Pro 3D printing build plate adhesives. For more information on how to get the best performance out of Magigoo adhesive products refer to User Manual for Magigoo Products (www.magigoo.com/tested-...
Page 20
4 Maintenance The Coater is designed to be used on a daily basis. The components like thin film applicator, valves and pump may lose original functionality with normal wear and tear. If the glue dots do not form a consistent row of 13 dots, check if valves need to be cleaned or replaced.
In the event repair or replacement is not Magigoo Coater product (the “Product”), possible the Manufacturer may elect to including all accessories supplied with it offer an appropriate refund.
5.3 Conditions & Limitations By offering this warranty, the Manufacturer Since warranty claims are conditional on accepts no liability for providing any the submission of the original purchase additional services or for any damages invoice and packaging, the Manufacturer or compensation for losses or injury of advises purchasers to store the invoice and any kind resulting from product failure or official packaging in a safe place.