Subscribe to Our Youtube Channel
Related Manuals for Schertler ARTHUR PRIME
Summary of Contents for Schertler ARTHUR PRIME
- Page 1 ARTHUR • U S E R • M A N U A L P R I M E S E R I E S - A N A L O G D E S K T O P M I X E R V1 EN W W W .
- Page 2 I’m delighted that you have purchased a SCHERTLER® ARTHUR PRIME mixer. It is our pleasure to welcome you to a growing family of musicians and technicians, including many of the world’s leading soloists and sound engineers, who have chosen to work with SCHERTLER® products.
- Page 3 INTRODUCTION The PRIME mixer series is based on the same technology used in SCHERTLER’s ARTHUR Format 48 mixer, guaranteeing best possible sound quality. The same high-quality preamps are found on the input channels, the same hi-voltage (48 V) power supply offers superior headroom, and the same No Negative Feedback (NNFB) structure gives a fast response and natural attack.
-
Page 4: Important Safety Information
Unplug your mixer during lightning storms, or if it is not going to be used for a while. (Remove the plug from the mains socket to completely disconnect the mixer.) Your mixer does not contain any “user serviceable” parts. Servicing and/or repairs should only be carried out by qualified personnel. See MAINTENANCE AND REPAIR (below). MIXERS ARTHUR PRIME... -
Page 5: Operational Safety
SCHERTLER technical assistance center. (For more information, contact us at the address on the last page of this manual.) -
Page 6: Power Supplies
ART48-PS12: Compact switching power supply provided with the mixer ART48-PS36: Optional 3.6 A high-end linear power supply ART48-PSPRO: Optional 10 A high-end linear power supply (this can power up to 3 ARTHUR PRIME mixers together) Linear power supplies better suit the noise level needed in professional environments such as recording studios, and offer an even wider dynamic range than the switching power supply. -
Page 7: Starting The Mixer
STARTING THE MIXER Plug the power supply’s connection cable into the ARTHUR PRIME’s DC IN connector (see page 10). ARTHUR has no on/off switch: when your mixer is not in use, its power supply should be disconnected. Note: The linear power supplies can be switched on or off using the on/off switch on the power supply itself. - Page 8 (interrupted.) Blue light = not depressed (bypassed). 6. 10V: This delivers the necessary 10 V supply for all SCHERTLER electrostatic pickups (STAT and BASiK Series). It enables the pickup to be directly connected to the YELLOW instrument input without using its original preamp.
- Page 9 8. HI: This lets you tune the high range of the audio spectrum (4.5 kHz upwards) from +/- 15 dB with a slope of 18 dB / octave. The 3rd order structure “keeps” the circle of influence within the filter’s audio band so as not to overlap with the MID filters.
- Page 10 “line level” devices might be connected to the line inputs. The AUX SENDS are the same as on the microphone input channel 3. AUX 1: Postfade, for controlling the amount of signal sent to the internal reverb and to the master section’s MIXERS ARTHUR PRIME...
-
Page 11: Line Channels
AUX 1 OUT for the use of external effects (see Master Section, 2). 4. AUX 2: Prefade and useful for setting the amount of signal sent to a stage monitor connected to the master section’s AUX 2 OUT (see Master Section, 4). 5. - Page 12 MAIN LEFT/RIGHT outputs (1) and subsequently to a PA system or recording device. Note: ARTHUR PRIME has 30 dB of headroom, so its electronics and output amps are rarely likely to clip. The main purpose of these meters is to monitor the level of signal flow to successive audio devices.
-
Page 13: Master Section
8. DECAY L and 9. REV LEFT: These controls let you regulate the reverb and its decay on the left channel. Note: Very useful if you want to set the reverb following the room acoustics, or use the effect in a more creative or unusual way. -
Page 14: Signal Flow
SIGNAL FLOW MIXERS ARTHUR PRIME... -
Page 15: Technical Information
TECHNICAL INFORMATION Weight 2.2 kg Dimensions (LxDxH) 22.6 x 37 x 6 cm Construction Anodized aluminum assembled box Total gain 73 dBu Pad (attenuation) Max input level +4 dBu (mic) +21 dBu (Yellow input) Mic In connector Mic In sensitivity -59 to -15 dBu Mic In impedance 4.7 kΩ... - Page 16 Spring-type digital reverb - LR separate adjustments Preamp Class-A, no negative feedback, no integrated circuits Audio transformer Power consumption 22 W Supply 50 VDC input - w/ power supply Modular Available versions With wood or black metal side panels PRIME 9 MIXERS ARTHUR PRIME...
- Page 17 Weight 4.2 kg Dimensions (LxDxH) 42 x 37 x 6 cm Construction Anodized aluminum assembled box Total gain 73 dBu Pad (attenuation) Max input level +4 dBu (mic) +21 dBu (Yellow input) Mic In connector Mic In sensitivity -59 to -15 dBu Mic In impedance 4.7 kΩ...
- Page 18 Where can I buy a case for my ARTHUR PRIME? ARTHUR PRIME cases, along with other SCHERTLER product accessories, are available from the online web shop at www.schertler.com. You can buy the product itself and/or its accessories from the relevant product page. Various cases are available for the ARTHUR range of fixed-channel and modular mixers.
-
Page 19: Warranty
COPYRIGHT This manual is the property of SCHERTLER SA and, as such, is subject to Swiss copyright law. No part of this manual should be reproduced, edited or distributed without prior consent from SCHERTLER. - Page 20 VIA BEROLDINGEN 18 A C O U S T I C 6850 MENDRISIO SWITZERLAND · A U D I O · T +41 (0) 91630 0710 F +41 (0) 91630 0711 P R O D U C T S INFO@SCHERTLER.SWISS WWW.SCHERTLER.COM...
Need help?
Do you have a question about the ARTHUR PRIME and is the answer not in the manual?
Questions and answers