Page 1
DISHWASHER SERVICE MANUAL NOTE BEFORE SERVICING THE UNIT, PLEASE READ THIS MANUAL CAREFULLY FOR SAFETY AND CORRECT SERVICES. MODEL : D1420W(L,M,T,B,C,D,A)F D1421W(L,M,T,B,C,D,A)F D1422W(L,M,T,B,C,D,A)F D1423W(L,M,T,B,C,D,A)F D14131WF / D14135LF D14138AC / D14121WH LD-4321W / LD-4421M LD-4421PV / LD-4421NV l i t é...
CAUTION ! DISCONNECT POWER CORD BEFORE SERVICING RECONNECT ALL GROUNDING DEVICES IMPORTANT SAFETY NOTICE ! This service information is intended for individuals possessing adequate backgrounds of electrical, electronic and mechanical experience. Any attempt to repair this appliance may result in personal injury and property damage.
2. SPECIFICATION SPECIFICATION ITEM Rated Voltage / Frequency AC 220V/50Hz AC 230V/50Hz AC 240V/50Hz Installation Freestanding Place Settings Product Dimension(mm) 600(W) 600(D) 850(H) Product Weight(Kg) 60kg Color White / Luxury Silver / Titanium / STS Black / ACM / Dark Red / Perl Silver Tub Material Stainless Steel Control...
3. PARTS NAME 1. Control Panel 11. Upper Rack 2. Door Handle 12. Cutlery Rack 3. Front Cover 13. Detergent And Rinse Aid Dispenser 4. Lower Cover 14. Vapor Vent Cover 5. Display Window 15. Upper Spray Arm 6. Power Button 16.
4. FEATURES & TECHNICAL EXPLANATION 4-1 New Technology Introduction 4-1-1. High Temperature Rinsing (Extra Hot function) • During the high temp. Rinse course, water temperature in an dishwasher reaches 80°C, considerably higher than the average rinse temperature in conventional dishwashers(65°C). This is how Rinse 80°C can eliminate some bacteria such as salmonella.
Page 7
4-2 Display Panel � MODEL : D1420 / D1423 Series ① ① Program � MODEL : D1421 / D1422 Series ① ① Program - 8 -...
Page 8
② ② UV ③ ③ Indicator ④ ④ Time Left ⑤ ⑤ Beep On/Off ⑥ ⑥ Rinse ⑦ ⑦ Half Load ⑪ ⑪ Delay Start ⑩ ⑩ Spray ⑨ ⑨ Power ⑧ ⑧ Child Lock ② ② Cool Dry ③ ③ Indicator ④ ④ Time Left ⑤...
Page 9
① ① Program • When you want to select program, press this button. ② ② UV • If you want to sterilize the dishes, press UV button. • After drying cycle, sterilizer will be performed by UV lamp. • At this time, “St” code is displayed in display window. Cool Dry •...
Page 10
4-3 TEST MODE CHECK PROGRAM(START IN THE STATE OF THE CLOSED DOOR) Checking points The number of BUTTON DISPLAY pushing button Load Half Load + Rinse All LEDs are lighting 1 TIME 1n0H : 1U00 + POWER Button Dual Wash Program Button 1 TIME 11 : 11...
7. HOW TO DISASSEMBLE BEFORE DISASSEMBLING THE DISHWASHER ; 1) Remove the plug from electric outlet to avoid electric shock. 2) Close the Water Tap(faucet). 3) Remove all dishes and items in the dishwasher. 4) Remove the Lower Rack and the Upper Rack. 5) In case of the water softner assembly model, open the water softner cap to flow out the water to sump and drain to avoid the floor wet.
Page 14
4. Door Assembly 1) Front Cover Open the door. Remove 4 screws(long Type, stainless). Remove 6 screws(stainless). Close the door slowly and remove front cover downwards. 2) Control Panel Assembly Open the door. Remove 2 screws(stainless). Remove wire connection. Be sure the wiring should not be changed in reassembling.
Page 15
3) Fan Open the door. Remove the wire connections. Turn the Inner Cover counterclockwise. Remove the air duct. 4) Detergent Dispenser Close the door. Remove the wire connections. Remove 6 screws with brackets. Push the Detergent slowly pulling up the Flange by Standard Screwdriver.
Page 16
5. Tub assembly 1) Rack Remove the Upper rack and Lower rack. 2) Air guide Nut and Water softner Cap&Nut Turn the Air guide Nut counterclockwise. (Special tool might be needed.) Be careful the rubber packing of air guide assembly should not be lost. Turn the Water softner Cap counterclockwise.
Page 17
5) Nozzle Holder Disconnect the water guide Remove 4screws and lift it up 6) Sump Holder Remove the Sump Holder(5EA). 7) Base spacer Remove front 2 screws. Remove side 2 screws. Lift the front side of dishwasher and pull the base spacer forward. 8) Lower Frame Remove 2 screws.
Page 18
9) Tub sub Assembly Remove side 4 screws. Remove 3 Earth screw of right side. Remove rear 4 screws. Lift tub assembly upward. (Be sure water softner is not blocked.) Be careful not to be injured or scratch floor by the sharp edge of tub. 6.
Page 19
3) UV Lamp(Limited on some models.) Remove the wire connections. Remove side 4 screws. Push the UV Lamp slowly. 4) Door Bracket Remove 4 screws. Lift up ward. 7. Air Guide Assembly Lift it upward to disconnect from Water Softner. Disconnect the wiring connection.
Page 20
8. C-Base Assembly Remove the wire connections. Lift them upward. Be careful not to wet the floor by the water left in the sump Pull out the float switch with pressing downward softly.(not on all models) Detach the washing motor and heater assembly by pulling opposite direction to sump.
Page 21
3) Vario Motor & Soil sensor Remove the wire connections. Remove 2 screws for Vario Motor. Pull the Vario Motor, Soil Sensor and Micro switch. 4) Impeller & Washing Motor Remove the wire connections. Remove 10 screws to disassemble the Impeller and Check valve.
Page 22
5) Power cord assembly & Noise Filter Turn the power cord assembly 90 and take it off. Remove 2 screw. 6) Aquastop Press the holder hook as shown in figure. Pull the hose assembly. 7) Drain Hose Press the rear side hook. Pull the holder forward.
Page 23
7-2. DISASSEMBLE C-BASE ASSEMBLY Be careful not to be injured by the sharp edge of tub. 1. Top Plate See 7-1. 1. (Page 16) 2. Low Cover See 7-1. 2. (Page 16) 3. Cabinet-R/L See 7-1. 3. (Page 16) 4. Put the Dishwasher upside down. Be careful not to wet the floor by the water left in the air guide.
Page 24
6. Disconnect the wire Remove the wire from the wire hook at the base. Remove 3 Earth screws of right side. Remove the Float switch. 7. Base spacer Remove front 2 screws. Remove side 2 screws. Lift the front side of dishwasher and pull the base spacer forward.
Page 25
9. Remove the side screws Remove side 4 screws. Remove rear 4 screws. Remove 3 Earth screws of right side. Lift base upward slightly (You can’t lift up base perfectly because of some parts connecting to base.) 10. Disconnect the connecting points between tub and base Disconnect noise filter.
8.TROUBLE SHOOTING METHODS A. TROUBLE SHOOTING ACCORDING TO DISPLAYED ERROR MESSAGE POSSIBLE CAUSE ERROR MESSAGE REMEDY FOR ERROR OCCURRENCE The Water Tap is not opened. Open the Water Tap. INLET ERROR The Inlet Hose is kinked. Repair the Inlet Hose. The Filter of inlet valve clogged a) Close the Water Tap.
Page 27
POSSIBLE CAUSE ERROR MESSAGE REMEDY FOR ERROR OCCURRENCE EXCESS ERROR The Inlet Valve is troubled. Replace the Inlet Valve. displayed The Air Break is troubled. Replace the air breaker. Condition The Sensor Assembly is troubled. Replace the sensor assembly. Excessive water is sup- The Controller is troubled.
B. TROUBLE DIAGNOSES AND REPAIR BY SYMPTOM No Power on when the power button pressed. • Insert the Plug Correctly. The plug is correctly inserted in the • Check the electricity is failed or not. Socket-Outlet? The Fuse or • Replace the Fuse or Circuit Breaker of house. Circuit Breaker of house is O.K? The Thermal Fuse...
Page 29
The Wash Pump/Motor does not run. • Close the Door Tightly. The Door is tightly • Check the Door Switch in Latch Handle. closed? The Pump/Motor is • Remove the cause of block or replace the Pump/Motor. not blocked? The circuit of Pump/ •...
Page 30
Washing Results are not Satisfactory After washing, are there still Reduce the amount of Rinse-Aid White deposits or streaks on (for Streak) the dishes? Does salt refill lamp blink? (Refill salt) After washing, are there still food soils on the dishes? Check that : - the amount of detergent Correctly used or not - Filters clogged or not.
Page 31
Power Button not automatically off after operation. Check the button is blocked by foreign materials. Check the Power Switch.(Replace it, if necessary.) Check the Controller.(Replace it, if necessary.) - 32 - - 32 -...
9. INSTALLATION INSTRUCTION Step1: Prepare Cupboard opening 1. This dishwasher is designed to fit to the size shown as below. 2. Select a location as close to sink as possible for easy connections to water and drain lines. 3. The dishwasher should not be installed more than 3 meters from sink for proper drainage. 4.
Page 33
Step 2 : PREPARE ELECTRICAL WIRING CAUTION For personal safety, remove house fuse or open circuit breaker before installation. Do not use an extension cord or adapter plug with this appliance. Electrical and grounding connections must comply with the national electrical code/provincial and municipal code and/or other local codes.
Page 34
Step 5 : DRAIN LINE CONNECTION 1. If the end drain hose does not fit to the drain line, use a piece of rubber connector (not supplied) that must be resistant to heat and detergent and may be obtained from a plumbing shop. 2.
Page 35
Drain Hose Extension Drain Hose extension kits are available from through your local service centre. Extend drain Hose as shown below. 200 mm Max. Sink Copper pipe fl 20mm flared at drain nose and other end if required. Use the couplings for connections when you extend drain hose.