Advertisement
Quick Links
Em50 Em50
Quick Start Guide
Introduction
Thank you for purchasing an Em50 series data logger. This data collection device
allows you to collect and store data from up to five sensors. The stored data can be
downloaded using the included USB cable or via radio to a base station (in case of
the Em50R). It is con-figured using either DataTrac ,or ECH
Packing List
Please check to make sure all listed items are present. If any item is missing or
damaged, please contact Decagon or your local distributor.
•
Em50 series data logger (Em50 or Em50 )
•
USB cable
•
Packet with 5 zip-ties and 5 AA alkaline batteries
•
Antenna (Em50R)
•
USB flashdrive with Software, driver and manual.
Note: The DataTrac or ECH2O Utility software and driver is required for
communication with the Em50 series data loggers. The software and driver must be installed
before using the Em50 (see the manual for software and driver installation instructions).
Turning on and Configuring the Em50
Install the 5 AA Alkaline batteries (included with shipment).
Note: Em50 olar logger comes with batteries reinstalled.
activate batteries. Use only Ni H (Nic el
olar logger.
Press the silver reset button located above the batteries.
o
ro
or
r
ir
o
ro
i
o
o
i o
i
io
s sors o
i
i
r
si
r io
io
ro
io or
o
i
Em50 o ar
O software
2
emove battery ull tab to
etal Hydride batteries with the Em50
o r o
r s
or o
i i or
i i
o i so
o
i
ro o
si
i
o
r
si
i
or
s
s
s r
s
io
ro
o orr s o
i
o
i
ro
s i
Em50 Em50
Introduction
Thank you for purchasing an Em50 series data logger. This data collection device
allows you to collect and store data from up to five sensors. The stored data can be
downloaded using the included USB cable or via radio to a base station (in case of
the Em50R). It is con-figured using either DataTrac ,or ECH
Packing List
Please check to make sure all listed items are present. If any item is missing or
damaged, please contact Decagon or your local distributor.
•
Em50 series data logger (Em50 or Em50 )
•
USB cable
•
Packet with 5 zip-ties and 5 AA alkaline batteries
•
Antenna (Em50R)
•
USB flashdrive with Software, driver and manual.
Note: The DataTrac or ECH2O Utility software and driver is required for
communication with the Em50 series data loggers. The software and driver must be installed
before using the Em50 (see the manual for software and driver installation instructions).
Turning on and Configuring the Em50
Install the 5 AA Alkaline batteries (included with shipment).
Note: Em50 olar logger comes with batteries reinstalled.
activate batteries. Use only Ni H (Nic el
olar logger.
Press the silver reset button located above the batteries.
s
o
or
r
i
o
rs o
io
i
r
si
io
io or
Em50 o ar
Quick Start Guide
etal Hydride batteries with the Em50
ro
o r o
r s
r
i i or
ir
o
ro
o
o
i o
i
si
s sors o
i
si
i
r io
s
ro
o orr s o
o
i
o
i
ro
O software
2
emove battery ull tab to
or o
s
i i
o i so
r
i
ro o
i
o
r
rs o
or
s
s
s r
io
ro
i
s i
Advertisement
Related Manuals for Decagon Devices Em50
Summary of Contents for Decagon Devices Em50
- Page 1 Note: The DataTrac or ECH2O Utility software and driver is required for communication with the Em50 series data loggers. The software and driver must be installed communication with the Em50 series data loggers. The software and driver must be installed before using the Em50 (see the manual for software and driver installation instructions).
- Page 2 Installing the Em50 Installing the Em50 Attach the Em50 in an upright position to a firm post or PVC pipe, using Attach the Em50 in an upright position to a firm post or PVC pipe, using the 5 zip ties or similar fasteners.