Download Print this page

Samsung BN68-03005A-01 Quick Setup Manual

Series 5.
Hide thumbs
   

Advertisement

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two persons lift and move the LED TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the LED TV placed down, it may lean to one side.
Screws (M4 X L12)
Guide Stand
Stand
1
Connect the Guide Stand to the
Stand using five screws (M4 X L12)
Rear
as shown.
2
3
With your TV upright, connect the
Fasten two screws (M4 X L8) at
TV to the Stand as shown.
position 1, and then fasten three
screws (M4 X L8) at position 2.
Screws (M4 X L8)
2
Rear
1
Step 2
: Install the Batteries into the Remote
To install batteries into your remote control,
follow these steps:
1. Lift the cover on the back of the remote
upward as shown in the figure to the
right.
2. Install two AAA batteries.
Make sure to match the + and - ends of the batteries to the diagram in
the battery compartment.
3. Replace the cover.
Step 3
: Connect Power and Antenna or Cable
VHF/UHF Antenna
Connect Ant In to
Antenna Cable
(Not Supplied)
• Wall cable jack
• VHF/UHF Antenna
or
• Cable or Satellite box
Ant or Cable Out
Use a 75 ohm (round) cable.
Step 4
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to connect your
TV to an external A/V device.
We recommend using HDMI for the highest picture
quality.
When connecting to
AV IN
on the back of your
TV, attach the video cable (yellow) to the green
jack next to the
AV IN
label. The jack will not
match the color of the video cable (yellow).
Lowest Quality Connection
Top view
Audio/Video connection (480i only)
Using an Audio/Video Cable
Audio Cable (Not Supplied)
AUDIO OUT
Front
Video Cable (Not Supplied)
VIDEO OUT
Rear
Step 5
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the
MENU
button. To turn on your TV, press the
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using your remote control, select
the language for the On Screen
Select Language of the OSD.
Display (OSD), and then press the
ENTERE button.
Menu Language
2
Select Home Use, and then
press the ENTERE button.
If you select Store Demo, the TV will reset your picture and audio settings
every 30 minutes.
3
Select Antenna Source. If Antenna Source is Air, Cable or Auto, you must
select your cable system type. After selecting source, select Search; then
press the ENTERE button on your remote.
Most cable systems are Standard (STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4
The TV memorizes the available channels. This process can take up to 45
minutes.
5
After the TV has memorized the channels, choose the Clock Mode. Select
Auto if you have a digital channel in your area. Select Manual if you don't, or
if you have a cable or satellite box. When done, press the ENTERE button.
If you select Manual, the clock setting screen appears.
HDMI Cable (Not Supplied)
HDMI to DVI Cable (Not Supplied)
Audio Cable (Not Supplied)
Good Connection
Component connection (up to 1080p)
Component Cable (Not Supplied)
DVD, Blu-ray player, cable box,
COMPONENT OUT
STB satellite receiver, VCR
Audio Cable (Not Supplied)
Device
AUDIO OUT
6
Select the daylight savings time setting: Off or On, and then press the
ENTERE button.
This function is only available when the Clock Mode is set to Auto.
7
Select the time zone in which you live, and then press the ENTERE button.
8
After the time zone screen, The connection method for best HD screen
POWER
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
Plug & Play
The Enjoy your TV. screen appears. Then press the ENTERE button.
English
Changing the Screen Size
Español
:
Français
Your TV has several screen size options, each designed to work best with specific
U Move E Enter
types of video input. If you have a cable box or satellite receiver, it may have its own
set of screen sizes as well.
To change the screen size, press the
you press it, your TV displays the current setting. Thereafter, each time you press
the
P.SIZE
button, you change the size of the picture on the screen.
The following sizes are available:
16:9 Wide screen
4:3 Standard screen
Zoom 1
Screen Fit: Displays the full image without any cut-off when HDMI (720p /
1080i / 1080p) or Component (1080i / 1080p) signals are inputted.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other
audio device to enjoy enhanced Sound quality.
Best Connection
HD connection (up to 1080p)
Using an HDMI Cable
HDMI OUT
DVD, Blu-ray player, HD cable box,
HD STB (Set-Top-Box) satellite
receiver
Device
Very Good Connection
HD connection (up to 1080p)
Using an HDMI to DVI Cable
Connecting a PC
DVI OUT
Connect your TV to a PC to use it as a Monitor.
Device
AUDIO OUT
Using a Component Cable
DVD, Blu-ray player, cable box,
STB satellite receiver, VCR
Device
D-Sub Cable (Not Supplied)
Changing the Picture Mode
Your TV has four preset Picture Modes with factory adjusted settings, each
designed to give you an excellent picture under specific conditions.
To change the Picture mode, press the
time you press it, your TV displays the current setting. Thereafter, each time you
press the
P.MODE
The Picture Modes are listed and described in the table below:
Description
Mode
Brightens picture. For a vibrant, enhanced image in brightly lit or
Dynamic
sunny room.
Standard
For a bright, detailed picture in a normally lit room.
For a comfortable, easy-on-the-eyes picture in a normally lit room.
Natural
Movie
For a studio quality cinema picture in a dimly lit or dark room.
To change the Picture Mode, follow these steps:
1. With the TV on, press the
appears.
P.SIZE
button on your remote. The first time
2. Using the ▲ or ▼ on your remote, select Picture Mode.
3. On the Picture Mode menu, use the ◄ or ► on your remote to select the
Picture Mode you want.
4. Press the
EXIT
Setting the Clock
Before you can use your TV's On/Off Timer, you must set the clock. To set the
Wide Fit
clock, follow these steps:
1. Turn on your TV, press the
Time.
2. Select Clock Mode, and then press the ENTERE button.
3. Choose Auto or Manual.
Zoom 2
Screen Fit
x
If you select Auto, the current time will be set automatically using the time
from a digital channel.
x
If you select Manual, you can set the Month, Day, Year, Hour, Minute
and am/pm directly by pressing up, down, left and right arrow button on
your remote.
4. Press the
RETURN
Analog Audio connection
Using an Audio Cable
Amplifier / DVD home theater
AUDIO IN
Audio Cable (Not Supplied)
Digital Audio connection
Using an Optical Cable
Digital Audio System
Optical Cable (Not Supplied)
OPTICAL
HD connection
HDMI to DVI Cable
(Not Supplied)
Using an HDMI to DVI Cable
DVI OUT
AUDIO OUT
Audio Cable (Not Supplied)
Using a D-Sub Cable
Audio Cable (Not Supplied)
AUDIO OUT
PC OUT
P.MODE
button on your remote. The first
button, you change the mode of the picture on the screen.
TOOLS
button on your remote. The Tools menu
button to exit the menu.
button on your remote, then select Setup →
MENU
button on your remote when done.

Advertisement

   Related Manuals for Samsung BN68-03005A-01

   Summary of Contents for Samsung BN68-03005A-01

  • Page 1: Quick Setup Guide

    Quick Setup Guide Step 4 Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.) 1-800-SAMSUNG (1-800-726-7864) STOP Use one of the connections below to connect your Samsung Electronics America, Inc.

  • Page 2

    Sharer) to transmit an encrypted security code called an access key. If Pure High-throughput (Greenfield) 802.11N mode is selected and the Encryption type is set to WEP, TKIP or TKIPAES (WPS2Mixed) for your AP, Samsung TVs will LAN Cable (Not Supplied) not support a connection in compliance with new Wi-Fi certification specifications.

This manual also for:

Un55c5000qf, Un55c5000, Un55c5000qfxza, 5000

Comments to this Manuals

Symbols: 0
Latest comments: