Related Manuals for elero Combio-868 LI
Summary of Contents for elero Combio-868 LI
- Page 1 Combio-868 LI 28 563.0006 Information for use Keep for future use. 18 111.0703_EN_0321...
-
Page 2: Table Of Contents
Deleting the programmed handheld / wall-mounted transmitter Servicing Cleaning Maintenance General notes on troubleshooting Repairs Decommissioning and disposal Disassembly Disposal Certification and imprint EU Declaration of Conformity Legal Disclosure 2 | EN Ⓒ elero GmbH Ⓒ elero GmbH EN | 3... -
Page 3: Introduction
(ECG, electronic control gear) ATTENTION An elero handheld/wall-mounted transmitter (at least 1) Danger, possibly resulting in damage to property. is also required. The Combio-868 LI can be controlled by several transmitters. Safety instructions Follow the instructions in these manuals to ensure Target group proper and safe use. -
Page 4: Warranty
L blue (N) antenna green- Warranty yellow Connection diagram with/without ballast • The warranty period for Combio-868 LI is in brown accordance with the legal regulations. Damages blue (N) N power grid green- caused due to improper use are excluded. -
Page 5: Preparation
Connection and installation Conformity CE (FCC / IC) Item number 28 563.0006 WARNING Risk of injury, damage to the Combio-868 LI and its surrounding area due to improper electrical connections. 8 | EN Ⓒ elero GmbH Ⓒ elero GmbH EN | 9... -
Page 6: Commissioning
The + sign in the text indicates pressing the buttons simultaneously. • Screw the Combio-868 LI to the surface by means Diagram of programming mode of the ring lug using a suitable screw. • Affix the Combio-868 LI using a self-adherent... -
Page 7: Asynchronous Programming Mode (Standard)
Asynchronous programming mode Asynchronous programming mode (standard) (standard) Start programming mode: Combio-868 LI changes Asynchronous programming mode is the standard pro- Press the [P] programming to asynchronous program- gramming mode. In asynchronous programming mode, button for approx. 1 second. ming mode and the light... -
Page 8: Synchronous Programming Mode
• If more than 10 receivers at once are in programming down for 3 seconds. mode, the transmitter changes to group program- Start programming mode: Combio-868 LI changes to ming mode. Once programming is complete, group Press the [P] programming synchronous programming programming mode has to be terminated manually in button for approx. -
Page 9: General Control Options
[STOP ] button for at [UP ▲] + [STOP ■] Longer Delete maximum user-de- least 6 seconds. than 6 fined brightness value and seconds restore standard value 16 | EN Ⓒ elero GmbH Ⓒ elero GmbH EN | 17... -
Page 10: Adapting An Illuminant
Adapting an illuminant [DOWN ▼] buttons, set value. The factory setting of the Combio-868 LI allows a power the desired brightness setting between 10% and 100%. The power cannot be value and then briefly press the [DOWN ▼] buttons + set below 10%. -
Page 11: Deleting The Programmed Handheld/ Wall-Mounted Transmitter
Restoring the absolute lower dimming limit Servicing Operating procedure Result Cleaning The components of the Combio-868 LI do not require Press the buttons The illuminant goes out. The [OPEN ▲] + [DOWN ▼] absolute lower dimming limit any special cleaning providing they are protected inside for 6 seconds. -
Page 12: Repairs
[OPEN ▲] and [DOWN ▼] program correctly and [DOWN ▼] buttons incorrectly The Combio-868 LI must be disposed of in accordance buttons is in- programmed with the legal regulations for electronic devices. terchanged The packaging must be disposed of separately in accordance with the applicable rules for cardboard and plastic. -
Page 13: Certification And Imprint
Certification and imprint EU Declaration of Conformity elero GmbH hereby declares that the Combio-868 LI is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: www.elero.com/downloads-service/downloads Legal Disclosure elero GmbH Maybachstr.
Need help?
Do you have a question about the Combio-868 LI and is the answer not in the manual?
Questions and answers