Advertisement
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, & general workshop practice regulations are adhered
to when using this equipment.
WARNING! Disconnect from mains power before changing accessories, servicing or maintenance.
maintain the Stapler/Nailer in good condition (use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous
and will invalidate the warranty.
Use this product in a suitable working area. Keep area clean, tidy and free from unrelated
materials. Ensure there is adequate lighting.
WARNING! Always wear approved eye or face protection when operating the Stapler/Nailer.
Remove ill fitting clothing, ties, watches, rings, other loose jewellery, and contain and/ or tie back long hair.
Wear appropriate protective clothing and keep hands and body clear of working parts.
maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
Keep children and unauthorised persons away from the working area.
DO NOT use this product for a task it is not designed to perform.
DO NOT operate where flammable gases or liquids are present.
DO NOT operate if any parts are damaged or missing. This may cause failure and/or possible injury.
DO NOT carry by the cable.
DO NOT get the Stapler/Nailer wet or use in damp or wet locations.
DO NOT point at other persons or animals.
DO NOT operate if you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT carry the Stapler/Nailer with your finger on the power switch.
When not in use disconnect from the mains power supply, remove the staples/nails from the
magazine and store in a safe, dry, childproof area.
2. INTRODUCTION AND SPECIFICATIONS
GS/TUV approved 230V electric stapler and nailer. Takes nails from 15-30mm and staples from 15-25mm. fires
up to 20 shots per minute. Suitable for fastening a wide range of materials from upholstery to timber. Soft grip
handle for comfort and control. fitted with ASTA/BS approved non-rewirable plug.
Nail Capacity: . . . . . . . . . . . . . . . . . . . . . . . 15-30mm
Staple Capacity: . . . . . . . . . . . . . . . . . . . . . 15-25mm
Replacement Staples: . . . . . . . . AK7063.01 (15mm)
3. OPERATING INSTRUCTIONS
LOADING STAPLES/NAILS
3.1.1 Ensure the stapler/nailer is not plugged into the mains while staples/nails are being loaded.
3.1.2 Always keep stapler/nailer with the exit hole facing away from you, preferably towards the surface to be
stapled/nailed.
3.1.3 Release loading spring by pressing the release button inwards, then downwards (fig 1), always secure
stapler/nailer and be weary of the spring extending from the loading slot.
3.1.4 Once the staples/nails are loaded in the loading slot (with the points facing downwards towards the base)
reinsert the loading spring (fig 2), lining up the grooves and clip the release button back into place.
USING THE STAPLER/NAILER
3.2
Grip the tool firmly and push the stapler exit against the item to be stapled and squeeze the trigger.
Note: The staple exit must be pressed down firmly as this product is fitted with a safety device in the head
which must be fully depressed before the staple will fire. If you are trying to staple a hard material such as
wood you may find pressing down on the head of the tool with your free hand will improve the staple
driving.
AK7063.02 (20mm)
AK7063.03 (25mm)
Original Language Version
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2kg
Replacement Nails: . . . . . . . . . . AK7063.04 (15mm)
AK7063.05 (20mm)
AK7063.06 (25mm)
23/10/09
AK7063
Issue: 2 -
Advertisement
