Sealey AK7064 Quick Start Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
ELECTRICAL SAFETY.
WARNING! It is the owner's responsibility to read, understand and comply as follows:

You must check all electrical equipment and appliances to ensure they are safe before using.
You must inspect power supply leads, plugs and all electrical connections for wear and damage.
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An
RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also
recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly important
to use an RCD together with portable products that are plugged into an electrical supply not protected by an
RCCB. If in doubt consult a professional electrician. You may obtain a Residual Current Device by contacting
your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1 The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be
tested by a qualified electrician at least once a year by using a Portable Appliance Tester (PAT).
1.1.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition
of the appliance, and the safety of the appliance operator. If in doubt about electrical safety, contact a qualified
electrician.
1.1.3 Ensure the insulation on all cables and the product itself is safe before connecting to the mains power
supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4 Ensure that cables are always protected against short circuit and overload.
1.1.5 Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, especially
power connections, to ensure that none are loose.
1.1.6 Important: Ensure the voltage marked on the product is the same as the electrical power supply to be used, and
that plugs are fitted with the correct capacity fuse.
1.1.7 DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8 DO NOT pull power plugs from sockets by the power cable.
1.1.9 DO NOT use worn or damaged leads, plugs or connections.
Immediately replace or have repaired by a qualified electrician.
A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage,
cut off and fit a new plug according to the following instructions
(discard old plug safely). (UK only - see diagram at right).
Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the green/yellow earth wire to the earth terminal 'E'.
b) Connect the brown live wire to live terminal 'L'.
c) Connect the blue neutral wire to the neutral terminal 'N'.
After wiring, check there are no bare wires, that all wires have been correctly
connected and that the wire restraint is tight. Double insulated products are
often fitted with live(BROWN) and neutral (BLUE) wires
only. Double insulated products are always marked with this symbol
Check you model carefully to see which type of product your have. To re-wire
a double insulated item connect the brown and blue wires as indicated above.
DO NOT connect brown or blue to the earth terminal.
1.1.10 Cable extension reels. When a cable extension reel is used it should be fully
unwound before connection. A cable reel with an RCD fitted is recommended
since any product which is plugged into the cable reel will be protected. The section of the cable on the cable
reel is important. This should be at least 1.5mm
cable reel is suitable for this product and for others that may be used in the other output sockets, we recommend
the use of 2.5mm section cable.
²
Original Language Version
INSTRUCTIONS fOR:
ELECTRIC NAILER
15-32MM
mODEL:
Blue
Neutral
Wire
section cable but to be absolutely sure that the capacity of the
²
AK7064
Yellow & Green
Earth Wire
.
FUSE RATING
THIS PRODUCT MUST
BE FITTED WITH A:
13 AMP FUSE
AK7064
Brown
Live
Wire
Wire
Restraint
Issue: 2 - 23/10/09