Related Manuals for Lang Quick-Point 85720
Summary of Contents for Lang Quick-Point 85720
- Page 1 Original Instructions Quick•Point Modular Plates ® I t e m n u m b e r 8 5 7 2 0 / 8 5 7 1 0 LANG Technik GmbH • Albstraße 1-6 • D-73271 Holzmaden • www.lang-technik.de • Version 2021/10...
- Page 2 This documentation is subject to errors and omissions. LANG Technik GmbH reserves all rights to this documentation. Product modifications: Modifications to the product by the customer void the warranty. No modifications may be made to the product without the manufacturer‘s consent.
-
Page 3: Table Of Contents
Contents Chapter 1 Product Description Page Unit Versions Dimensions Chapter 2 Technical Data General Data Material Scope of Supply Repair Chapter 3 Design and Function Assembly Maintenance Chapter 4 Servicing Malfunctions/Errors Chapter 5 Warnings Intended Use Personnel Requirements Protective Equipment and Safety Chapter 6 Decommissioning Disposal Chapter 7 Explanation of Symbols... -
Page 4: Unit
Product Description Unit The Quick•Point Modular Plates are an enhancement to the well-established variants ® with improved pull-down force and the option to use connectors to connect and align them without an alignment gauge. An added bonus for the customer is that these connected plates can be used with only one tightening screw. -
Page 5: Chapter 2 Technical Data
The conversion kits for connecting multiple plates and the cover plug remover must be ordered separately and in the correct quantity. 2.4 Repairs Please contact LANG Technik GmbH directly if any item is damaged or malfunctioning. LANG Technik GmbH • Albstraße 1–6 • D-73271 Holzmaden, Germany • Phone: +49 7023 9585-0... -
Page 6: Assembly
Design and Function Assembly If several Quick•Point Modular Plates are interconnected, the corresponding mounting ® holes must be available for the particular machine table and the relevant covers must be removed on the connection ends. Plate 1 (pos. 1) includes the caps for the connectors (pos. 2) as well as the cover of the through-hole (pos. - Page 7 Design and Function A conversion kit is needed in order to connect them in series. This includes an actuation bolt (pos. 7) inserted in the through-hole between the plates, as well as two connectors (pos. 8). If the plates are attached with these, they must be secured with the enclosed cap screws (pos.
-
Page 8: Use
Double plate Double plate 50 Nm (85720) (85720) Double plate Double plate Single plate 60 Nm 85720 (85720) (85710) LANG TECHNIK NOTE If the modular plates are used without connecting them, do not exceed a tightening torque of 30 Nm. -
Page 9: Maintenance
® make sure that all unused clamping points are capped off with the enclosed cover plugs (pos. 12). pos. 12 LANG TECHNIK NOTE Clean the Quick•Point Modular Plates after use and protect them from corrosion. No ® maintenance by the customer is required. -
Page 10: Chapter 4 Servicing
Servicing Malfunctions/Errors Do not to exceed the 30 Nm tightening torque. In addition, clean the Modular Plates, as well as all other components, and protect from corrosion. The manufacturer assumes no liability for any damage in this regard. Warnings Intended Use The operating company is responsible for using the product as intended, with caution and under the appropriate conditions. -
Page 11: Chapter 6 Decommissioning
Specified in EU Directive 2018/851 Comply with country-specific disposal regulations when disposing of equipment. LANG Technik products are not considered household waste. Failure to comply with disposal requirements is a regulatory offense. Accessories and packaging are recycled in an environmentally friendly manner. -
Page 12: Chapter 7 Explanation Of Symbols
Explanation of Symbols Symbols Please pay attention to the following warning symbols Read all the operating instructions carefully before commissioning for the first time and keep it in a safe place for future use Please read and follow the technical and safety instructions The use of protective gloves made of tough, resistant material is recommended A helmet and safety goggles are recommended for personal safety... - Page 13 LANG Technik GmbH Albstraße 1–6 D-73271 Holzmaden Phone: +49 7023 9585-0 Fax: +49 7023 9585-100 Internet: www.lang-technik.de General e-mail: info@lang-technik.de Sales e-mail: sales@lang-technik.de...