Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Extreme Networks ES660B
Summary of Contents for Extreme Networks ES660B
- Page 1 ES660B USER’S MANUAL V.01.17.SZ ...
-
Page 2: Important Voltage Information
WARING: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a buzzard. This appliance is not intended for use by persons (including children) with reduces physical, sensory or mental capabilities, or lack of experience and know ledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. -
Page 3: Target Heart Rate Zone
– Remove the SAFETY KEY when not in use. – Inspect the treadmill for worn or loose components before each use. – Do not operate the treadmill if: – 1. The power cord is damaged. – 2. The treadmill is not working properly _ 3. - Page 4 HOW LONG SHOULD YOU EXERCISE? Sustained exercise conditions your heart, lungs and muscles. The longer you are able to sustain exercise within your target heart range, the greater the aerobic benefits. To begin maintain 2~3 minutes of steady, rhythmic exercise, then check your heart rate. BEGINNER TREADMILL PROGRAM EXERTION LEVEL WEEK 1...
- Page 5 WARNING! : Use extreme caution when assembling the treadmill. Failure to do so could result in injury NOTE: Each step number in the assembly instructions tells you what you will be doing. Read and understand all instructions thoroughly before assembling the treadmill. 1.
- Page 6 Power switch Incline motor Controller Overload protector Air shock Cushion Frame Frame move wheels...
- Page 8 Motorized Treadmill Installing Sketch Map...
- Page 9 Motorized Treadmill Installing Sketch Map screw M8x15 screw M8x15 washerφ8 screw M8x15 screw M8x15 washerφ8 screw M8x80 screw M8x80 washerφ8 nut M8 screw M8x15 screw M8x15 washerφ8 screw ST4x15 screw ST4x15...
-
Page 10: Function Instruction
Operation Manual I. Function instruction： 1.1 25 preset mode P1-P25, every mode 30 minutes; 1.2 Can set time countdown, distance countdown and calorie countdown workout modes; 1.3 Speed: 1-16 km/h 1.4 Incline: 0—15%; 1.5 Each 7 fast keys of speed and incline ; 1.6 Hear rate handle function;... -
Page 11: Engineer Mode
2.1 “MODE”: mode selection key, in stop position, cyclical select (P1-P25-P1). 2.2 “SELECT”: SET KEY, in manual position, cyclical select countdown time, countdown distance, countdown calorie workout mode, under every mode set workout time. 2.5 “STOP”: Stop key, in running position press to pause, in setting mode press to standby position; 2.6 “START”: Start key, in stop position press to start. -
Page 12: Error Information
V. Error information 3.1 E0 means safety key is off, put on the safety key. 3.2 E1 means can not get speed signal in 10 S automatic stop. 3.3 E2 overcurrent error, the controller continuous 3s over rated current. 3.5 E4 motor voltage saltation or motor line not connected. 3.6 E5 interruption of communication 3.7 E6 breakdown of power valve BELT ADJUSTMENT... - Page 13 c. If the belt is still not at centre, repeat the above steps until the running belt is on centre. C). After the belt is centered, increase the speed to 16kph (or highest speed) and verify that it is running smoothly.
- Page 14 HOW TO SPRAY SILICONE ON DECK? A). Find the silicone bottle. It is located in the hardware kit package included with this treadmill. B). Find a straw and put it onto the silicone bottle as the drawing shows. C). Spray silicone evenly on treadmill deck as the drawing shows. (ATTENTION: The treadmill MUST BE STOPPED before applying the silicone lubricant.