Advertisement
Quick Links
TOILET PRESSURIZED WATER INTAKE KIT
MODEL #TPWK12 (12V DC) - TPWK24 (24V DC) - TPWK32 (32V DC)
MAINTENANCE AND INSTALLATION INSTRUCTIONS
THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND
FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
WARNING:
Raritan Engineering Company, Inc. recommends that a qualified person or electrician install this
product. Equipment damage, injury to personnel or death could result from improper installation.
Raritan Engineering Company, Inc. accepts no responsibility or liability for damage to equipment,
injury or death to personnel that may result from improper installation or operation of this product.
WARNING:
HAZARD OF SHOCK OR FIRE
Always use recommended fuse, circuit breaker and wire size.
WARNING:
HAZARD OF FLOODING - Always shut off seacock(s) before leaving the boat unattended.
Double clamp all below waterline hose fittings and check frequently for integrity.
Water Solenoid Valve
The Toilet Pressurized Water Intake Kit is designed for use with the Crown Head II, SeaEra, Atlantes and
Atlantes Freedom toilets. It can be used to convert a raw water flush toilet to freshwater flush.
1-800-352-5630
www.raritaneng. com
With Atmospheric Vacuum Breaker
Atmospheric Vacuum Breaker
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Raritan TPWK12
Summary of Contents for Raritan TPWK12
- Page 1 TOILET PRESSURIZED WATER INTAKE KIT With Atmospheric Vacuum Breaker MODEL #TPWK12 (12V DC) - TPWK24 (24V DC) - TPWK32 (32V DC) MAINTENANCE AND INSTALLATION INSTRUCTIONS THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
- Page 2 IMPORTANT • Improper winter lay up is a major cause of marine toilet failure. • Use only nontoxic antifreeze. • Flush toilet several times to clear waste from system. • Dispose of all antifreeze in accordance with local and federal regulations. •...
-
Page 3: Specifications
Parts Included SPECIFICATIONS Atmospheric Vacuum Breaker with fittings Vacuum Breaker with fittings Water Solenoid Valve with fittings 4" (10.16cm) 2" Water Solenoid Valve Mounting Bracket (5.08cm) Additional Parts Required • Two stainless steel toilet mounting bolts or 5" lag screws (1/4" [6mm]) (12.70 cm) •... - Page 4 Mounting Water Solenoid Valve 1. Locate valve on a solid flat surface in an area that is dry and well ventilated. 2. Mark and drill holes for water solenoid mounting bracket. NOTE: Hole size will depend on type of bolts/ screws used (1/4"...
- Page 5 PLUMBING WARNING: Hazard of potable water contamination. The vacuum breaker must be Vacuum Breaker installed with any installation using a potable water source. Min. 6" (15.24cm) Water Solenoid IMPORTANT Toilet Valve Ù • Fittings and 90° bends should be kept to a Toilet minimum.
-
Page 6: Troubleshooting
WIRING WARNING: Hazard of Shock and Fire Toilet Pressurized Water Intake Kit Wiring Wall Mounted • Always use proper wire, wire connectors and Blue Momentary Flush POS (+) fuse/circuit breaker. See Specification Chart Control Panel on page 3. Orange • Secure wire properly. - Page 7 WATER SOLENOID VALVE AND ATMOSPHERIC VACUUM BREAKER EXPLODED VIEW AND PARTS LIST (Quantities are one unless otherwise indicated) Before ordering, locate required part on exploded parts view to be sure you are ordering the correct part. Item Part No. Description Item Part No.
- Page 8 1. TO OBTAIN WARRANTY SERVICE, Consumer must deliver the product prepaid, together with a detailed description of the problem, to Raritan at 530 Orange St., Millville, N.J. 08332, or 3101 SW 2nd Ave. Ft. Lauderdale, FL 33315. When requesting warranty service, purchaser must present a sales slip or other document which establishes proof of purchase.
Need help?
Do you have a question about the TPWK12 and is the answer not in the manual?
Questions and answers