Related Manuals for Latham ECLIPSE
Summary of Contents for Latham ECLIPSE
- Page 1 THE E C L I P S E AUTOMAT I C SA F E T Y POOL COV E R ™ DECK MOUNT SYSTEM INSTALLATION GUIDE...
- Page 2 16. Drill (cordless or corded) 33. Pencil or marker 17. Set of drill bits (1/4” down to 1/16”) 34. 6 - 8 clamps Optional Power tools Skill saw with carbide tipped blade, Sawzall, Grinder. © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 3 The parts list at above is typical for most pools up to 20’ x 40’ and includes all parts necessary to install the Coverstar ECLIPSE system, however, parts will vary for longer or wider pools and according to your specific order.
-
Page 4: Table Of Contents
Step By Step Instructions Page/Step Laying out the cover tracks ........5/2 Splicing the tracks together........5/4 Cutting the tracks to length ........5/9 Checking for square ..........6/12 Attaching the tracks to the deck ......6/14 © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 5: Laying Out The Cover Tracks
With tracks extended at least 18” past the waterline at the opposite end of the pool, cut the tracks so they extend 18” past the waterline at the mechanism end. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 6: Checking For Square
Place the track back over the holes in the deck. Fasten the track screws (34) halfway through the tracks into the plastic anchors. The screws will be fastened completely later in the installation. © Latham Pool Products, Inc. 2019. All rights reserved. - Page 7 MECHANISM Step By Step Instructions Page/Step Attaching the roll-up tube ........8/2 Positioning the roll-up tube/mechanism.....8/4 Extending the Pulley brackets .........8/5 Anchoring the mechanism ........9/14 Wiring the electrical switch ........10 © Latham Pool Products, Inc. 2019. All rights reserved.
-
Page 8: Attaching The Roll-Up Tube
This is crucial for a properly operating cover. Adjust the non-motor end as needed to level the roll-up tube. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 9: Anchoring The Mechanism
It is important that the end and non-motor end to the deck. the mounting holes in the mechanism into the mechanism be mounted square to the deck. cover track. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 10: Wiring The Electrical Switch
Wiring the Electrical Switch The control switch must be mounted in an all-weather box, in a location where 100% of the pool is visible. Connect the control switch according the diagram below. © Latham Pool Products, Inc. 2019. All rights reserved. - Page 11 Attaching the ropes to the rope reel ....15/28 Running the cover over the pool .......15/30 Attaching the cover and bonding wire ...15/31 Adjusting the ropes ..........15/34 Adjusting the torque limiter ........16/37 Adjusting the brakes ..........16/40 © Latham Pool Products, Inc. 2019. All rights reserved.
-
Page 12: Opening The Cover
Make the wire that is attached to the rope around sure ALL screws are flush with the top of the the first and second pulleys. tracks. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 13: Attaching The Cover Leading Edge
Make attached to the front corners of the cover to the wheel assemblies. sure they can slide freely inside the leading edge tube. © Latham Pool Products, Inc. 2019. All rights reserved. - Page 14 Be sure the screw does rope. lighter or torch to burn the ends of the rope. In not interfere with the leading edge insert. most cases you will only need to cut one rope. © Latham Pool Products, Inc. 2019. All rights reserved.
-
Page 15: Attaching The Ropes To The Rope Reel
Pull the excess that the cover needed to travel to close all rope off the rope reel. the way. While holding the rope, run the switch in the cover position. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 16: Adjusting The Torque Limiter
Adjust pulled into the track. To adjust this brake, use both brakes equally. two 7/16” wrenches and tightening or loosening the bolts thru in the brake block. © Latham Pool Products, Inc. 2019. All rights reserved. - Page 17 After the cover system is installed, it is critically important to instruct the home owner on how to operate the cover system safely and do routine maintenance. Use the following check list and the ECLIPSE Use & Care Guide as your primary instruction source. Use & Care Guide Page How to use the cover pump ...........4...
- Page 18 © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 19 QUESTIONS? For questions about this installation guide, contact your independent Coverstar distributor. Latham Pool Products 787 Watervleit-Shaker Rd. L9784 Updated 3.8.19 bm Latham, NY 12110 USA © Latham Pool Products, Inc. 2019. All rights reserved.