Related Manuals for Latham Coverstar Atom
Summary of Contents for Latham Coverstar Atom
- Page 1 UNDER TRACK SYSTEM with Aluminum Lid AUTOMATIC SAFETY POOL COVER INSTALLATION GUIDE © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 2 33. Pencil or marker 16. Drill (cordless or corded) Skill saw with carbide tipped blade, 17. Set of drill bits (1/4” down to 1/16”) 34. 6 - 8 clamps Sawzall, Grinder, Angle drill © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 3 Coverstar system; however, parts will vary for longer or wider pools and according to your specific order. Lid Options: Additional instructions are available for different lid options. - Walk-On Tray Lid - Flushmount Lid - Flat Lid © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 4 STANDARD UNDER TRACK Step By Step Instructions Page/Step Step by step installation instructions ....5/1 © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 5 11, step 9). extend into the housing. track. Remove the guide feed. Do this for the track on both sides of the pool. © Latham Pool Products, Inc. 2019. All rights reserved.
-
Page 6: Table Of Contents
Connecting the roll-up tube ......7/2 Adjusting the mechanism height ....7/4 Positioning the roll-up tube/mechanism ..7/7 Anchoring the mechanism feet ....8/12 Anchoring the pulley brackets ..... 8/18 Wiring the electrical switch ......9/20 © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 7: Step By Step Instructions
Adjust height of the non-motor end feet if needed to level the roll-up tube. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 8: Anchoring The Mechanism Feet
Tighten the nylock nuts on the adjustable Use the appropriate screws and anchors brackets. depending on the type of cover box being used. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 9: Wiring The Electrical Switch
Wiring the Electrical Switch The control switch must be mounted in an all-weather box, in a location where 100% of the pool is visible. Connect the control switch according the diagram below. © Latham Pool Products, Inc. 2019. All rights reserved. - Page 10 Attaching the ropes to the reels ....14/30 Running out the cover ........14/34 Attaching the cover and bonding wire ...14/35 Mechanism Adjustments Rope Adjustments ..........15/38 Torque Limiter ..........15/41 Rope Reel and Non-motor end Brake ..15/44 © Latham Pool Products, Inc. 2019. All rights reserved.
-
Page 11: Opening The Cover Box
The spacer needs to are already installed. end at the inside edge of the cover box. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 12: Routing The Ropes
Continue pulling the excess rope through Insert the second rope in the same way into should now look like this. the pulleys. the other vertical pulley. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 13: Inserting The Leading Edge
(If the encapsulation was cut flush is used to keep the track from being pulled to the inside of the cover box, secure the into the cover box. track using a track retainer bracket (20)). © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 14: Attaching The Ropes To The Reels
(28). The first screw on each end of the track. tube needs to be 3 inches from the end of the tube. As the cover rolls up on the tube, the webbing will be rolling up over the cone. © Latham Pool Products, Inc. 2019. All rights reserved. -
Page 15: Mechanism Adjustments Rope Adjustments
If they do not, they should be tightened enough to prevent the rope from spooling off the reel as the cover is opening. © Latham Pool Products, Inc. 2019. All rights reserved. - Page 16 To adjust this brake, use two 7/16” Adjust both brakes equally. wrenches to tighten or loosen the bolts in the brake block. © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 17 CLASSIC ALUMINUM LID Step By Step Instructions Page/Step Installing the lid brackets ........18/1 Assembling the aluminum lid ....... 18/4 Attaching the lid to the deck ......... 18/7 © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 18 Fasten the lid to the deck with #12 pan is attached to the deck. The pool cover drill through these holes and into the head screws (23). installation is now complete. concrete deck using a 1/4” masonry bit. © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 19 Who is authorized to operate the cover system ....6 Pool chemicals and cover life ..........8 Proper maintenance and care of the cover system ..8-9 Inform the customer on pool safety ....Back cover © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 20 © Latham Pool Products, Inc. 2019. All rights reserved.
- Page 21 QUESTIONS? For questions about this installation guide, contact your Independent Coverstar Distributor. Latham Pool Products 787 Watervleit-Shaker Rd. Latham, NY 12110 USA L3532 3.13.19 bm © Latham Pool Products, Inc. 2019. All rights reserved.