Lokshop LS4801 Assembly Instructions

Item No LS4801
Signal Kit
Semaphore Home Signal, 1:220 (Z)
Hp0/Hp2 two arms
Dieses Produkt ist
D
kein Spielzeug.
Nicht geeignet für
Kinder unter 14
Jahren!
This product is not
GB
a toy.
Not suitable for
children under 14
years!
Ce produit n'est
F
pas un jouet.
Ne convient pas
aux enfants de
moins de 14 ans!
Made for:
Lokshop eK
Froschhöhle 9
D - 76229 Karlsruhe
Tel.: +49721/490350
Fax: +49721/4903520
E-Mail: mail@lokshop.de
10 - 16 V, DC/AC
The following instructions should be
read carefully!
Congratulations!
You have bought a high-quality product, supposed to give pleasure during
assembly and use. Please read these instructions carefully before assemb-
ling or using the product and check if the content of the packaging is com-
plete.
Safety advices
This kit contains small parts which can easily be swallowed by children. Not
suitable for children under 14 years!
The electric and electronic components may only be run with approved
low-voltage transformers. The components are sensitive to heat and may
only be exposed to high temperatures for a short time. Do not "roast"!
A soldering iron develops temperatures up to 400°C. Do not leave it unat-
tended! Keep distance to combustible materials and use a heat-resistant
base-pad for work. Any electrical connection-work may only be done when
disconnected from the main power supply.
All sources of current must be secured against short-cut in order to prevent
fire. Resistors are necessary for regular function. Lamps run without resis-
tors will be destroyed. Resistors may not be covered with insulating materi-
als in order to guarantee sufficient cooling.
Please check at first if the kit is complete. In case of damaged or
missing parts due to the sellers improper packing, please send
back the whole package.
3
1
16 17 18
8
10
19
20 21
7
for
29
5
6
1
signal mast
1
1
base plate
2
1
3 mast top
1
imitation of lantern-winch
4
1
imitation of drive casing,
5
front wall
1
imitation of drive casing,
6
back wall
1
post plate, long
7
1
post plate, short
8
1
socket of positioning-wire
9
1
signal arm, long
10
1
positioning mechanism
11
2
front of lantern-case.
12
2
13 back part of lantern-case
2
base of lantern-case
14
2
15 filter-lens, white
The following tools are required:
Small edge cutter
Flat pliers and pointed tweezers
Soldering iron with thin tip, solder (pref. Ø 0,5 mm)
Superglue
Assembly:
For a better control, you can tick each finished work-step in a box at the
left side of the text.
1.
Cut the cable (27) into two pieces of equal length (30 cm), then
remove the insulation of both ends of both parts (approx. 3 mm) and
tin-plate it. Prepare another piece (length: 3 cm) the same way. Be
careful, the cable can easily be torn!
2.
Shorten that lead of the diode (24) where the black ring is tending to
up to a length of approx. 3 mm. Solder one of the cables of 30 cm of
length on the diode. Black ring should tend to the cable. Then insula-
te the junction with black shrink-tube (29). Shrink on with hair-drier
or hot-air-gun. [Fig. 1]
Content:
9
15
13
12 14
15
13
24
12
14
4
2
f
ilter-lens, green
1
16
filter-lens, red
17 1
lantern-screen, two holes
18 1
signal arm, short
1
19
filter-lens, yellow
20 1
lantern-screen, one hole
21 1
circuit-board with 2 LED,
1
22
green/red
circuit-board with 1 LED,
1
23
yellow
diode 1N4148 or similar
1
24
resistor, 820Ω
1
25
(grey-red-brown-gold)
Without illustration:
positioning wire
1
26
cable
1
27
labels
1
28
shrink-tube, black
1
29
shrink-tube, yellow
1
30
11
25
22
23