Intended Use; Technical Data - BorMann PRO BBP3900 Manual

EN
18. DO NOT use hot melt glue to take the place of structural fasteners.
19. The glue sticks used with this glue gun will begin to soften at about 60 °C. Don't use the glue on objects or materials that are subjected to heat.
20. Avoid accidental glue discharge. Forcing glue sticks into an unheated tool may damage the tool or cause hot glue to be unexpectedly expelled from nozzle
when the operating temperature is achieved. Glue may discharge from a heated tool without pressure applied to the trigger (1). Use a heat resistant material
to protect the work surface.
21. This tool is not a toy. Keep out of the reach of children.
Safety of others
1. This tool can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the tool in a safe way and understand the hazards involved. Children shall not
play with the tool. Cleaning and user maintenance shall not be made by children without supervision.
2. Children should be supervised to ensure that they do not play with the tool.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product.
MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
Important safety instructions for battery cartridge
1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial transports e.g. by third parties, for-
warding agents, special requirement on cartridge aging and labelling must be observed. For preparation of the item being shipped, consulting an expert for
hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and cartridge up the battery in
such a manner that it cannot move around in the cartridge aging.
11. Follow your local regulations relating to disposal of battery.
CAUTION: Only use genuine Bormann batteries. Use of non-genuine Bormann batteries, or batteries that have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will also void the Bormann warranty for the Bormann tool and charger.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at 5°C - 45 °C . Let a hot battery cartridge cool down before charging it.

Intended use

The glue gun is intended to be used only by adults who have read and understood the instructions and warnings in this manual, and can be considered respon-
sible for their actions. The glue gun is intended for solvent-free gluing of materials such as paper, cardboard, cork, wood, leather, textiles,foam materials, plastic
(except PE, PP, PTFE, Styrofoam® and plasticised PVC), ceramics, porcelain, metal, glass and stone.
Description of main parts (Picture Α)
1. Nozzle
2. Glue stick chamber
Battery and charger are not included among the items
3. LED indicator
of standard delivery. They are sold separately.
4. On/Off switch
5. Switch trigger
6. Soft handle
7. Glue stick
8. Battery Cartridge
9. Button of Battery Cartridge

Technical Data

Voltage: 20V
Glue stick diameter: 10-12mm
5
WWW.BORMANNTOOLS.COM