Table of Contents Operating Instructions (24 – 45) Intended use Important safety instructions Product features Included in the box Unpacking and setting up Operation Startup / Fan speeds Operation Display Air quality indicator Filter replacement indicator only IDEAL AP40 PRO: Remote control (replacing the battery) Remote control (function) App Control...
Important safety instructions Introduction Thank you for choosing a device from IDEAL. Intended use • The device is used exclusively for cleaning the ambient air indoors. • Please read these operating instructions before starting to use the device and please follow the safety instructions. The operating instructions must be kept available with the device at all times.
Page 4
Important safety instructions Important safety instructions • Children being supervised not to play with the appliance. • Do not block the air intake and outlet. technical parameters. Improper usage may pose a threat to life and health. • Disconnect the mains plug prior to any cleaning or maintenance work. •...
Unpacking and setting up Installation guidelines for optimum performance: • Place the device at least 10 cm away from the wall. • Keep the device away from areas subjected to draft (wind). • Make sure that furniture, fabrics or other objects do not come in contact with the air intake/outlet or block them.
Page 7
Unpacking and setting up Take the textile cover (only IDEAL AP40 PRO) component A). tabs into the three recesses provided for this and lock it at the locking component (A) then to the socket. correctly, the switch button (B Note: Safety information complete and secure attachment of the cladding and safety covers...
Operation Startup / Fan speeds 1. Plug in the power cable, press the switch button (B automatic mode . The switch button lights up. 2. Press the switch button to exit automatic fan speed 1 . The switch button flashes once.
Operation / Display Display Air quality indicator The air quality is displayed in 3 colours (in all fan speeds): Switch button (B) green: good air quality Switch button yellow: average air quality Switch button red: poor air quality Filter replacement indicator The switch button (B intervals).
Page 10
Remote control (only IDEAL AP40 PRO) Battery usage • Always use 3V lithium batteries CR2025 for the remote control. • If the remote control is not going to be used for a long time, please remove the battery. Unsuitable location •...
Remote control (only IDEAL AP40 PRO) Replacing the battery • Open the battery compartment by pressing (A) and pulling out (B) at the same time. • Insert a new battery into the battery compartment, making sure the polarity is correct (+ / -). •...
Remote control (only IDEAL AP40 PRO) On/off button Quiet button Automatic button Turbo Auto Timer buttons Fan speed buttons Locking button Function Select the required fan speed Select the required timer time Visualisation only in the app (smartphone / tablet). Press the locking button again to unlock.
Filter replacement Filter replacement Note: Take the mains plug out of the socket. mains plug out of the device. component (A) and remove. Remove the textile cover (only IDEAL AP40 PRO). cartridge.
Page 14
Filter replacement Put the textile cover (only IDEAL AP40 PRO) back (locking component A). tabs into the three recesses provided for this and lock it at the locking component (A) then to the socket. installed correctly. Note:...
App Control / WLAN App Control smartphone / tablet (iOS /Android). WLAN Querying the WLAN status: Press the WLAN button the WLAN is enabled when the switch button flashes blue the WLAN is disabled when the switch button flashes white. Enabling/disabling WLAN Press the WLAN button and while the switch button is flashing (blue or white), press the...
Cleaning and maintenance / Accessories Cleaning and maintenance • Do not use any solvents. These could damage the housing surface. • Do not use any substances containing silicone, since this could destroy the air quality sensor. • Do not test the effectiveness of the air quality sensor with high quantities of gas, or alcohol, since this could destroy the air quality sensor.
Troubleshooting Is the power cable securely connected to the back of the device? Make sure that the power cable is not damaged in any way Check both ends of the power cable. Make sure that these are plugged in and that the (page 29).
Page 18
Troubleshooting The switch button is lit up only dimly or not lit up at all. switch button (page 30). If you press the switch button once, the air Disable the Quiet function by selecting a different fan speed via the app or on the remote control (only IDEAL AP40 PRO).
Page 19
Troubleshooting surface? Place the device on an even surface. speed? Use the switch button to set a lower fan speed. with your problem? Contact: Service Service • www.krug-priester.com • service@krug-priester.com...
Technical data IDEAL AP30 PRO: Power supply 200-240V 50/60Hz / 100-120V 50/60Hz Power consumption 30W (200-240V) / 25W (100-120V) Suitable for rooms 20 to 40 m² * Air flow rate (max.) 310 m³/h Dimensions (L × W × H) 298 × 255 × 398 mm...
Page 21
The company Krug + Priester has the • Quality management system according to DIN EN ISO 9001:2015 • Environmental management system according to DIN EN ISO 14001:2015 • Energy management system according to DIN EN ISO 50001:2018 Terms of warranty IDEAL provides a warranty for this device from the date of purchase.
Page 22
Subject to technical changes. EC-declaration of conformity - Herewith we declare that GS-IDENT. No. UL-IDENT. No. IDEAL AP30 PRO Made in Germany 11731002 10731002 IDEAL AP40 PRO Made in Germany 11731001 10731001 - complies with the following provisons applying to it...
Page 23
Supplier‘s Declara on of Conformity 47 CFR § 2.1077 Compliance Informa on This device complies with part 15 of the FCC Rules. Opera on is subject to the following two condi ons: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera on.
Need help?
Do you have a question about the IDEAL AP30 PRO and is the answer not in the manual?
Questions and answers