1. Manuals
  2. Brands
  3. Pace Technologies Manuals
  4. Grinder
  5. PENTA 5000
  6. Instruction manual

Pace Technologies PENTA 5000 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲
3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1-520-882-6598 Fax +1-520-882-6599 email: pace@metallographic.com
Equipment Type:
Model:
Electrical Requirements:
Frequency:
Motor Horsepower:
Manual Revision Date:
Please read this instruction manual carefully and follow all installation, operating and safety guidelines.
PENTA 5000 Hand Grinder
Five station hand grinder
PENTA 5000
N/A
N/A
N/A
April 24, 2022
I
M
NSTRUCTION
ANUAL
Web: https://www.metallographic.com

Advertisement

Table of Contents
loading

Related Manuals for Pace Technologies PENTA 5000

Summary of Contents for Pace Technologies PENTA 5000

  • Page 1 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...

  • Page 2: Table Of Contents

    PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...

  • Page 3: Warranty

    Terms and Conditions applying to all PACE Technologies Products 1. LIMITED WARRANTY AND DISCLAIMER: PACE Technologies Products are warranted for two years from the purchase date to be free from defects in material and workmanship under correct use, normal operating conditions, and proper application.
  • Page 4 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...

  • Page 5: Safety Guidelines

    Careful attention to this instruction manual and the recommended safety guidelines is essential for the safe operation of the PENTA 5000. Proper operator training is required for operation of the PENTA 5000. Any unauthorized mechanical and electrical change, as well as improper operation, voids all warranty claims.

  • Page 6: Product Description

    Water valve Grinding surfaces The PENTA 5000 is a 5-station hand-grinder for manual wet grinding of metallographic specimens. With 5 stations for coarse to fine grinding papers (240, 360, 400, 600, 800 and 1200 grit), specimens can be prepared to a near-polished surface. The surface quality after 1200 grit is typically acceptable for heat-treated and weld analysis specimens.
  • Page 7 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...

  • Page 8: Unpacking, Shipping And Installation

    PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...
  • Page 9 Web: https://www.metallographic.com 3.3 Installation Install unit carefully! Improper installation voids warranty. The PENTA 5000 should be placed on a flat stable surface. Connect to water supply and drain. After water and drain are connected, the system is ready for operation.

  • Page 10: Start-Up And Operation

    ANUAL 3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1-520-882-6598 Fax +1-520-882-6599 email: pace@metallographic.com Web: https://www.metallographic.com 4.0 Start-up and Operation 4.1 General The PENTA 5000 is a hand-grinding/polishing machine. Water valve Grinding surfaces 4.2 Loading Rolls Load pin into roll and...
  • Page 11 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...
  • Page 12 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...

  • Page 13: Maintenance

    Web: https://www.metallographic.com 5.0 Maintenance 5.1 Introduction The PENTA 5000 requires very minimal maintenance. However, to increase the life of the polisher, it is suggested that the unit be rinsed after use. 5.2 Cleaning outside cabinet The cabinet should be cleaned occasionally with a moistened cloth. Do not use any chemicals or cleaning abrasives.

  • Page 14: Troubleshooting

    PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...

  • Page 15: Metallographic Consumables

    PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...

  • Page 16: List Of Spare Parts

    PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...
  • Page 17 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...
  • Page 18 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...
  • Page 19 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...
  • Page 20 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...

  • Page 21: Mechanical Drawing

    PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...
  • Page 22 PENTA 5000 Hand Grinder - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲...

Table of Contents