Black & Decker bev BEHB101 Instruction Manual page 8

English
Tall glass:
1. Push the glass shelf up so it hides away in the tower.
2. Ensure the drip tray cover
3. Place a tall glass on the drip tray cover.
shaker:
The shaker LED 19 will light when a drink needs to be
shaken. In this case, use a shaker instead of a tall glass.
1. Push the glass shelf up so it hides away in the tower.
2. Ensure the drip tray cover is in place.
3. Place a shaker on the drip tray cover.
Inserting a Capsule (Fig. H, I)

WARNING: Cut Hazard. Do not probe capsule holder
area with fingers.

WARNING: Pinch point. Keep away from capsule
holder when closing capsule holder lid.

WARNING: Use only Bartesian capsule. Use with any
other capsule may result in damage to the appliance.
iMPORTAnT: Do not open capsule
iMPORTAnT: Once the capsule is punctured, it may drip
liquid. To avoid this, place a capsule in the capsule holder
just before mixing a drink.
1. Before inserting a capsule, place a glass or shaker on the
glass shelf 17 or drip tray
GLASS TRAY section
2. Select the capsule you wish to use.
3. To open the capsule holder, lift the capsule holder lid
until it clicks into place.
4. Ensure the bar code
debris. Wipe your thumb across the bar code before
inserting capsule into capsule holder.
5. Place the capsule in the capsule cup
holder. Ensure the capsule tab
cocktail maker will not operate if the capsule is inserted
any other way.
6. Ensure the capsule sits fully in the capsule cup.
nOTE: The scanner inside the capsule holder scans the code
on top of the capsule. This allows the cocktail maker to pull
from the correct bottles so it dispenses the correct drink.
7. Push the capsule holder lid down to close the capsule holder
until it clicks. Ensure the lid is fully closed before operating.
nOTE: If the capsule code is successfully read, the bottle
LEDs 16 will light under the bottles that are being used.
Ensure each bottle is in its correct place.
nOTE: If lights do not turn on, lift the capsule holder lid and
use a clean, dry towel to wipe the barcode scanner
capsule barcode 32 as shown in Fig. I. Then, repeat step 6.
Select Alcohol Strength (Fig. J)
To select the amount of alcohol to be dispensed into the
drink, turn the strength selector dial
left: less alcohol
•
• Right: more alcohol
The strength LEDs 15 will turn on and off as you turn the
selector, indicating the strength of the drink.
• ‑ mocktail (no alcohol)
6
4 is in place.
20 .
3 as described in the CHOOSE A
32 is clean from liquid and
23 located in the
24 faces to the left. The
31
25 .
• ‑ light alcohol content
• ‑ regular alcohol content
• ‑ strong alcohol content
Making a Drink (Fig. F–J)

WARNING: To ensure liquor is not dispensed while
making a mocktail, lift straw locks
bottles and keep the water bottle straw lock down.
1. Turn the cocktail maker on as described in the ON/
OFF section.
2. Place a glass or shaker on the glass shelf
depending on its height as described in the CHOOSE A
GLASS TRAY section.
3. Insert the desired capsule
as described in the INSERTING CAPSULE section.
4. Turn the strength selector dial
content as described in the SELECT ALCOHOL
STRENGTH section.
5. Bottles used for the drink recipe will light up. Ensure
bottles are installed in all locations illuminated.
6. Push the mix button
21
7. The bottle LED will light under the bottle whose liquid is
being dispensed.
8. It is complete when all the LEDs become solid.
9. Remove the capsule before removing the glass. The
capsule may drip when it is being removed and if left in
the holder.
22
nOTE: While making a drink, if the power button is turned off, the
appliance is unplugged, or after one minute in pause mode, the
mixing process will be reset, ending the mixing of the current drink.
If this happens, a small amount of alcohol may remain in the internal
lines. To ensure the next drink is not mixed with this remaining
alcohol, clean the lines as described in the CLEANING MODE section
before mixing another drink. To resume making the drink while in
pause mode, refer to the PAUSE MODE section.
nOTE: If the cocktail maker continues to dispense to the
point of overflow, turn the appliance off, lift the straw lock, or
lift the capsule holder lid
Bottle Runs Out During Mixing (Fig. F, J)
If a bottle runs out of liquid while the cocktail maker is
mixing a drink:
• The cocktail mixer will enter pause mode for 2 minutes to
allow you to replace the empty bottle. Refer to the PAUSE
MODE section for more information.
• Do not turn the power switch
reset the mixing process and the cartridge will no longer
and the
be able to be used.
nOTE: The unit will not flush the lines while the capsule
holder lid 22
To replace the empty bottle:
1. Remove the bottle as described in the REMOVING
BOTTLES section.
2. Install the a new bottle as described in the INSTALLING
BOTTLES section.
3. Press the mix button
from where it left off.
into the capsule holder
20
25 to set the alcohol
26 to begin making a drink.
22 .
14 off. Turning it off will
is lifted.
26 to resume mixing the drink
8 for the alcohol
17 or drip tray 3
21